Dits UFC4 problem - GSM-Forum

.:SARCAR:. · 08-18-2011, 11:05

Hello Dits,

today have some problem with my ufc4 . when I plug jaf main cable into my ufs , power light (ufs) became off . & after some seconds a message appear into system tray " usb device not recognized " . I just remove main A to B usb cable from ufs immediately . & also notice ufs became some hot !!

but other cables like mt , atf , cyclone works ok & read info form phone with ufc4.

I already replace main usb cable ( A to B) , replace another 2 ufs but problem remain same.

I think there is shortage . in main jaf cable of ufc4.

please help me dits team.

SMDSAFE · 08-19-2011, 09:08

Please check the connections

RJ48[TO UFC4] _______RJ45[TO JAF]
1...................................YELLOW CLIP
2...................................RED CLIP
3...................................6
4...................................1
5...................................2
6...................................8
7...................................BLACK CLIP
8...................................4
9...................................5
10..................................3

AND GIVE REPLY...

joalbert_ramos · 08-21-2011, 03:28

i thinks need to redesign your cable got difficuty in 3110c and e52 mobile ,v++ ,bs and gnd , are in side clip direction,3110c v++ and gnd ,bsi at reverse position

joalbert_ramos · 08-21-2011, 03:31

@ scsarcar
i got the same problem in HWK micro using dits cable not connected but solve it by turning bsi jaf off if you are using HWK and bsi 1 on

.:SARCAR:. · 08-21-2011, 21:32

@SMDSAFE ,

checked & found ok . RJ-48 to RJ-45 all connections r ok . while in ufc4 jaf main cable unplug from both ends.

but while connecting with hwk pin7 & pin5 of RJ-48 female connector(main ufc4 pcb) became short (in power off condition).

is it any problem?? need help.

08-18-2011, 11:05	#1 (permalink)
.:SARCAR:. No Life Poster Join Date: Jul 2006 Location: Midnapore,West-Bengal,India Posts: 4,271 Member: 322206 Status: Offline Sonork: 100.1594813/.:SARCAR:. Thanks: 17 Thanked 793 Times in 646 Posts	Dits UFC4 problem Hello Dits, today have some problem with my ufc4 . when I plug jaf main cable into my ufs , power light (ufs) became off . & after some seconds a message appear into system tray " usb device not recognized " . I just remove main A to B usb cable from ufs immediately . & also notice ufs became some hot !! but other cables like mt , atf , cyclone works ok & read info form phone with ufc4. I already replace main usb cable ( A to B) , replace another 2 ufs but problem remain same. I think there is shortage . in main jaf cable of ufc4. please help me dits team.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Sim card sleep mode problem with 6130	ratzfatz	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	4	05-22-2012 11:13
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	3	11-21-1999 18:43
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	09-11-1999 17:39
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	07-16-1999 00:44

08-19-2011, 09:08	#2 (permalink)
SMDSAFE Freak Poster Join Date: Jul 2006 Location: MARS Posts: 379 Member: 311990 Status: Offline Thanks: 59 Thanked 143 Times in 86 Posts	Please check the connections RJ48[TO UFC4] _______RJ45[TO JAF] 1...................................YELLOW CLIP 2...................................RED CLIP 3...................................6 4...................................1 5...................................2 6...................................8 7...................................BLACK CLIP 8...................................4 9...................................5 10..................................3 AND GIVE REPLY...

08-21-2011, 03:28	#3 (permalink)
joalbert_ramos Freak Poster Join Date: Jan 2006 Posts: 287 Member: 216705 Status: Offline Thanks: 28 Thanked 42 Times in 35 Posts	i thinks need to redesign your cable got difficuty in 3110c and e52 mobile ,v++ ,bs and gnd , are in side clip direction,3110c v++ and gnd ,bsi at reverse position

08-21-2011, 03:31	#4 (permalink)
joalbert_ramos Freak Poster Join Date: Jan 2006 Posts: 287 Member: 216705 Status: Offline Thanks: 28 Thanked 42 Times in 35 Posts	@ scsarcar i got the same problem in HWK micro using dits cable not connected but solve it by turning bsi jaf off if you are using HWK and bsi 1 on

08-21-2011, 21:32	#5 (permalink)
.:SARCAR:. No Life Poster Join Date: Jul 2006 Location: Midnapore,West-Bengal,India Posts: 4,271 Member: 322206 Status: Offline Sonork: 100.1594813/.:SARCAR:. Thanks: 17 Thanked 793 Times in 646 Posts	@SMDSAFE , checked & found ok . RJ-48 to RJ-45 all connections r ok . while in ufc4 jaf main cable unplug from both ends. but while connecting with hwk pin7 & pin5 of RJ-48 female connector(main ufc4 pcb) became short (in power off condition). is it any problem?? need help.