V36xx power-off when connect net - GSM-Forum

sjakie · 09-29-2002, 12:08

Hi,

Had this problem before, but never got into it.
Now i want to try it
Could someone tell me what to check first ?

Maybe PA, problem is i dont know name off this.
I have pictures but no code for PA.

Could be PA ?

Thanks
Sjakie

**Bert** · 09-30-2002, 10:58

yes, mostly is 1800 p.a faulty , it's marking code is ap119

***Pandemonio100*** · 09-30-2002, 11:29

Or probably there is one little resistor bad on the RF area. first to change Pa control all resistors.

sjakie · 09-30-2002, 11:43

Thanks for reply.
I discoverd removing U300, makes phone work on 1800mhz without power off.
replaced it with otherone, but again phone switches off wenn connecting to network.
Maybe i destroyed it by soldering ?

Thanks
Sjakie

sjakie · 09-30-2002, 13:54

Problem found

With closer look i saw C485 was sticking to another resistor.
Resoldered, all now ok.

thanks for the help

Regards
Sjakie

sjakie · 10-07-2002, 21:23

Hi, sorry for reopening but have again same problem

(

I desolder 900Mhz PA, phone worked good on 1800mhz.
Second i replaced PA 900, same problem.
Removed 1800 PA, same problem.
Put again another PA 900Mhz, phone seems Ok.
So i closed it up.
After 10 minutes 900 Mhz band getting no RX.
Power off and on phone, 3 seconds 900Mhz RX than Zero RX.
After that sometimes 2 seconds RX on 900Mhz.
Manual search gives all providers including 900Mhz.
When trying to get manual login 900Mhz its say registering than nothing.
Could it be FL470-460 problem ?

Thanks
Sjakie

xmobile · 10-08-2002, 23:13

Try to Flash phone with Full FLash.
Maybe help

09-29-2002, 12:08	#1 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	V36xx power-off when connect net(PART 2) Hi, Had this problem before, but never got into it. Now i want to try it Could someone tell me what to check first ? Maybe PA, problem is i dont know name off this. I have pictures but no code for PA. Could be PA ? Thanks Sjakie Last edited by sjakie; 10-07-2002 at 21:16.

10-07-2002, 21:23	#6 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	Part 2 Hi, sorry for reopening but have again same problem ( I desolder 900Mhz PA, phone worked good on 1800mhz. Second i replaced PA 900, same problem. Removed 1800 PA, same problem. Put again another PA 900Mhz, phone seems Ok. So i closed it up. After 10 minutes 900 Mhz band getting no RX. Power off and on phone, 3 seconds 900Mhz RX than Zero RX. After that sometimes 2 seconds RX on 900Mhz. Manual search gives all providers including 900Mhz. When trying to get manual login 900Mhz its say registering than nothing. Could it be FL470-460 problem ? Thanks Sjakie

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
T639 Power off when I connect	-luigi-	Easy-Unlocker	2	08-30-2008 00:02
Power Off When Connect Smart Moto	BCcommunication	Smart-Clip	2	04-04-2006 15:54
C55 powers off when leds off	sjakie	Siemens Hardware Repair Area	0	05-01-2003 13:07
mot t180 power off when login to net	david Sig	Motorola Hardware Repair Section	2	02-19-2003 08:40
Motorola V2288 and V51 Power off when i connect...	DrMobile	Old Legacy Motorola (EMMI)	1	09-14-2002 11:15

09-30-2002, 10:58	#2 (permalink)
Bert Product Manager Join Date: Oct 1999 Location: Hong Kong Posts: 1,463 Member: 596 Status: Offline Sonork: 100.33096 Thanks: 53 Thanked 352 Times in 47 Posts	yes, mostly is 1800 p.a faulty , it's marking code is ap119

09-30-2002, 11:29	#3 (permalink)
*Pandemonio100* Super Moderator Join Date: Feb 2001 Location: ITALY Age: 40 Posts: 3,598 Member: 3381 Status: Offline Thanks: 133 Thanked 1,007 Times in 264 Posts	Or probably there is one little resistor bad on the RF area. first to change Pa control all resistors.

09-30-2002, 11:43	#4 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	Thanks for reply. I discoverd removing U300, makes phone work on 1800mhz without power off. replaced it with otherone, but again phone switches off wenn connecting to network. Maybe i destroyed it by soldering ? Thanks Sjakie

09-30-2002, 13:54	#5 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	Problem found With closer look i saw C485 was sticking to another resistor. Resoldered, all now ok. thanks for the help Regards Sjakie

10-08-2002, 23:13	#7 (permalink)
xmobile Major Poster Join Date: Sep 2002 Location: Novi Sad,YU Posts: 43 Member: 15650 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Try to Flash phone with Full FLash. Maybe help