proper pinout and cable for E66 - GSM-Forum

josh11 · 11-08-2009, 13:21

i need proper pinout (picture) and cabel (3 or 7?) for e66. selectors shows diferrent pictures and cables.help

sjakie · 11-09-2009, 22:50

Hi, same here, saw lots of wrong pictures off e66.
Tried cable 3 and 7, both can flash, but not get into local mode.
Anyone really got good pinout for unlock, not copied from bad picture?

regards
Sjkaie

hendradoank4000 · 11-10-2009, 16:22

Maybe this helps you.
Translate this was bro ..!
Close the pin which I marked with red tape or anything that could be used to cover these pins,
and use Jig No3 ...!

Tested By me...

sjakie · 11-10-2009, 17:10

Thanks for picture, tried it , flashes ok, but no localmode, i tried several resistance
but no joy

Need simlock.

regards
Sjakie

josh11 · 11-11-2009, 17:11

thanx a lot. but what about unlock?

suskom · 03-12-2011, 12:02

to put phone in local mode just connect + , bsi and ground (resistence 5,1 ) to phone , push the on button, phone goes to local mode, then connect cable number 7 like the picture says. Done

11-08-2009, 13:21	#1 (permalink)
josh11 Junior Member Join Date: Feb 2007 Posts: 3 Member: 453373 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	proper pinout and cable for E66 i need proper pinout (picture) and cabel (3 or 7?) for e66. selectors shows diferrent pictures and cables.help

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Advanced UFS add-on pinout and cable test-point pinout	gopalhot	Nokia Hardware & Hardware-Repair Area	0	06-22-2008 19:29
Advanced UFS add-on pinout and cable test-point pinout	pager12	Nokia Hardware & Hardware-Repair Area	0	06-21-2008 03:02
X65 USB Cable PinOut and Drivers for SST	ednacell	S-Gold Based Phones	12	01-30-2005 11:09
Pinout and cable shematic LG3000	skystar	LG	3	06-03-2003 15:43

11-09-2009, 22:50	#2 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Online Thanks: 30 Thanked 32 Times in 27 Posts	Hi, same here, saw lots of wrong pictures off e66. Tried cable 3 and 7, both can flash, but not get into local mode. Anyone really got good pinout for unlock, not copied from bad picture? regards Sjkaie

11-10-2009, 16:22	#3 (permalink)
hendradoank4000 Junior Member Join Date: Nov 2009 Location: "West Java - South Borneo" Posts: 23 Member: 1151916 Status: Offline Thanks: 2 Thanked 10 Times in 7 Posts	Maybe this helps you. Translate this was bro ..! Close the pin which I marked with red tape or anything that could be used to cover these pins, and use Jig No3 ...! Tested By me...

11-10-2009, 17:10	#4 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Online Thanks: 30 Thanked 32 Times in 27 Posts	Thanks for picture, tried it , flashes ok, but no localmode, i tried several resistance but no joy Need simlock. regards Sjakie

11-11-2009, 17:11	#5 (permalink)
josh11 Junior Member Join Date: Feb 2007 Posts: 3 Member: 453373 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	thanx a lot. but what about unlock?

03-12-2011, 12:02	#6 (permalink)
suskom Junior Member Join Date: Nov 2006 Posts: 1 Member: 402023 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	to put phone in local mode just connect + , bsi and ground (resistence 5,1 ) to phone , push the on button, phone goes to local mode, then connect cable number 7 like the picture says. Done