๑۩۞۩๑ SETOOL Updates And News๑۩۞۩๑

[SHIJILFONOTLY]

-  from now on, unlock by altbypass method for qsd8250,msm7227 phones will also "unlock" semcboot.
-  qsd8250,msm7227 phones with "unlocked" bootloader can flash custom firmwares now
-  added few models to model list, so users don't get confused
-  different bugfixes, some are important.

Download Link

MIRROR LINK

[xxxman]

WARNING !!!

As there is too much "blocked" setool2 GEMALTO TOP cards,we investigated issue and found problem.

due to errors in controller firmware
( or due to incompatibility between smartcard/controller firmware/motherboard usb controller )
all smartcard readers i know, which are based on CY7C63001 are failed to send long data packet to/from smartcard.
it happens on some systems only, it can happen not immediately, but on "affected" system it happens always, earlier or later.

due to that, smartcard will receive WRONG command and SETOOL2 WILL BE "BLOCKED".
THAT IS NOT RELATED TO "BLOCKED CARDMANAGER" ISSUE ( ERROR #6982 )

i can not find ANY solution to that problem, other than NOT using Cypress CY7C63001-based readers with setool2 cards.


here is few pictures of AFFECTED readers:


you can also identify such reader by smartcard reader name and driver name:


if you will use that readers, your setool2 smartcard WILL BE BLOCKED - and i will unblock such card ONLY ONCE.

my strong recommendation is use om****y-based readers, like that:

they are working 100% on any system.


of course, usage of latest setool2 version is ABSOLUTE requirement.

[xxxman]

v1.12

- added altbypass support for xperia arc_s model, in other words, phones with 8255T chipset fully supported.
- added resurrection support for s1 qualcomm-based phones with totally damaged security zone.
resurrection procedure will be described in FAQ later,
however, in short it is standard "recovery+write gdfs+unlocking" chain.

7227,8250-based phones require special uart cables ( pinout included in docs ),
however it is highly recommended to use special GPG cables
8x55-based phones does not require any special cables.

as side effect, imei change possible now for s1 qualcomm-based phones.
for 7227,8250-based phones need select COM as interface, options are:
( signed mode, altbypass mode, do full unlock, allow to change imei when unlocking, use testpoint (gnd type) )
for 8x50-based phones need select USB as interface, options are:
( signed mode, altbypass mode, do full unlock, allow to change imei when unlocking )

cost of imei change 5 credits, please take in mind, that if you change imei, phone need to be unlocked,
so add another 5 credits for unlock procedure.
if you have calculated signature for some imei, then you can save 5 credits for unlocking

- added few models to model list, so users don't get confused
- different bugfixes

RapidShare Link

[Danish Shafiq]

Setool Latest Update Released v1.1201

-  resurrection procedure will now work for totally erased s1 qualcomm-based phones
   FAQ now have  resurrection procedure example.

-  forgot to post, that starting from v1.12 setool2 will check for faulty cypress-based reader and refuse to run,  
   if setool2 smartcard installed in such reader. 
   There is no any workaround. 
   Use om****y-based reader or other normal reader.

RapidShare Link

[xxxman]

extremely important message !!!

seems most of lately produced msm7227-based phones have chipset with FIXED security hole, which used to altbypass unlock.
( that is not 100% confirmed, we only have few reports, however better be warned )
such phones will DIE after successful unlock procedure.
such dead phones CAN NOT be recovered. ( perhaps, jtag can fix that, perhaps, qualcomm fixed jtag security hole too )

there is NO WAY to determine if phone has fixed chipset or chipset with security hole.

the ONLY safe way is to use unlock by resurrection cables.
if phone can be connected and booted by resurrection cables, phone is safe to unlock.
if phone can not be booted by resurrection cables, phone has fixed chipset and could not be unlocked.

you have been warned.
get and use resurrection cables.

update:

  e16 phone with manufacture date 11w38 affected, i think we should care about phones which produced after 11w26

[xxxman]

v1.1202

-  no testpoint altbypass unlock procedure will work now for msm7227-based phones,which using MCUs with fixed security bug.   
  resurrection cables will NOT work for MCUs with fixed security bug. Because of this,  
   phones, which are already dead should be recovered using jtag box, which can write ORIGINAL semc boot. 
   big thanks for help and testing to electrolandgsm.
 -  switch to usb interface was broken for DB200x phones, fixed.
 -  added few models to list, so users can use profiles for them.

RapidShare Link

[xxxman]

v1.1203

-  testpoint altbypass method will work now for msm7227-based phones,which using MCUs with fixed security bug.
   that means, resurrection cables will work for MCUs with fixed security bug.  
-  fixed problem with FOTA upgrade for msm8x55-based phones, unlocked by altbypass

RapidShare Link

[xxxman]

Starting from 25.12.2011 cost of unlock procedure, using alternative security bypass for semc phones,
based on msm7227,qsd8250,qsd8x55 chipsets will be 0 ( zero ) credits.

Such terms will be in effect until another announcement.

[xxxman]

SETool news: Starting from 03.01.2012 cost of unlock procedure, using alternative security bypass for semc phones,
based on msm7227,qsd8250,qsd8x55 chipsets will be 2 ( two ) credits.

We will watch closely on market situation with semc qualcomm solution and react correspondingly.

[Danish Shafiq]

v1.1204

- fixed "dead phone after unlock" for some latest j20 phones.
- x10 with android firmware 2.3.3 supported for altbypass unlock
- msm8x60 sony phones supported ( lt26,lt28,is12s,so-03d ). Standard operations supported - flash,trim area read/write.
  Network unlock only supported using s1 signature server, which is offline for us.
- added support for one interesting activation.

RapidShare Link

[Danish Shafiq]

smartcard update released for v1.1204 software.

after smartcard update, setool2 no more require internet connection or any credits to unlock any qualcomm-based semc phone.
all settings and procedures are same as usual, but internet connection no more required, if card is updated.

update is paid, cost 20 setool2 credits.
it is DOES NOT matter, if card was already activated or updated to work with >1.107 version.

LGTool will be activated and uploaded automatically during process.

for update procedure please read that thread.

[Danish Shafiq]

Quick Fix For Android 4 Firmware For Old Xperia Phones

Just Paste updated executable To v1.1204 Folder

[Danish Shafiq]

v1.1280

- fixed m1_aspen flashing
- fixed flashing of ICS firmwares for 8x55 phones
- removed java-based altbypass method for all a1 phones,except pnx5230-based phones.
- reset-based unlock method is now standard altbypass unlock method for a1 phones.
  you can not use usb as interface for altbypass unlock on db2000,db2010-based phones anymore.
  you do not need restoration files,bypass files ( still need them for pnx5230-based phone ).
  and ... altbypass unlock is much quicker and quite "one-buttoned" now ;)
- added x1 unlock via codes, all you need  -  enter IMEI on locks tab and press "request". Cost is 1 credit.

due to major core rewrite, some bugs can appear in a1 phone service patterns, despite i checked all supported phones in different modes.
if you will find problems, feel free to report them on forum.

RapidShare Link

[Danish Shafiq]

DB2020 Brown Phones Support Was Broken By Accident.
Please Use that quickfix.

Please note, that there NO NEED to use RESET operation for unlock anymore - use it ONLY when GDFS area totally trashed.
for any A1 unlock cases, just check signed mode +altbypass and press unlock/repair.

[Danish Shafiq]

v1.1286

- added quite complex, but working procedure to unlock last SEMC A2 phone, j108 cedar from network locks.
  beginners, stay away from this procedure. 
  other users, welcome to faq for details.
- STE U8500 sony phones supported ( lt22,mt26,st25 ). Standard operations supported - flash,trim area read/write.
  Network unlock only supported using s1 signature server, which is offline for us.
  STE U8500 support was done blindly, should work, but need to be tested.

RapidShare Link

4 Shared LINK

CLICK HERE