N7000 Write emmc done, but detected as SEC S5PC210 Test B/D

[MVNDOzone]

I change Emmc And Write Emmc



log

================================================== ====
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.


Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 15010056594C30304D19ED6D36118E21
CSD : D02701320F5903FFF6DBFFEF8A404067

eMMC Boot Information
Revision 1.5 (for MMC v4.41)
BOOT PARTITION : BOOT PARTITION 1
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x4 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 3584 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE : 15753805824 BYTES
BOOT PARTITION SIZE: 2048 KB
RPMB PARTITION SIZE: 128 KB


eMMC Device Information
Manufacturer ID: SAMSUNG
Device Type : Embedded BGA
Application ID : 00
Product Name : VYL00M
Product Rev : 1.9
Product SN : ED6D3611
Manufactured : January 2011

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 13 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
15010056594C30304D19ED6D36118E21.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

Start Writing 0x00000400 Blocks at 0x00000000
Partition Selected: BOOT 1

Total Elapsed Time 00:00:02
Write Success!
Start Writing 0x00000400 Blocks at 0x00000000
Partition Selected: BOOT 2

Total Elapsed Time 00:00:01
Write Success!
Start Writing 0x00020000 Blocks at 0x00000000
Partition Selected: USER AREA

Total Elapsed Time 00:01:48
Write Success!

i just write from working phone but phone cannot live

please help
whats wrong?

[malka4u]

share pinouts please

[argo1976]

EMMC is new? try to program jtag

[argo1976]

boot partition size is incorrect

[toninhosantos]

try change boot partition for user area partition and try again.

[MVNDOzone]

Originally Posted by argo1976

EMMC is new? try to program jtag

yes new emmc
i have try riff and medusa but not connected

boot size incorect?
please guide me

Originally Posted by toninhosantos

try change boot partition for user area partition and try again.

i have set boot partition to boot 1

eMMC Boot Information
Revision 1.5 (for MMC v4.41)
BOOT PARTITION : BOOT PARTITION 1
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x4 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 3584 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE : 15753805824 BYTES
BOOT PARTITION SIZE: 2048 KB
RPMB PARTITION SIZE: 128 KB

[syahdacell]

ANY ONE HAVE DONE??? some problem and no solution

[MVNDOzone]

I have done
Change emmc
Change clk

Sent from my MI 5 using Tapatalk