need boot1 boot2 and user area i9060 - GSM-Forum

ranagaurav · 12-23-2015, 15:16

phone dead during wrong flash file
i try to boot repair found emmc pinout but cant found boot1& boot2 or user area file
so plz rewqust to supporter plz provide i w8 kindy relpy

ranagaurav · 12-27-2015, 05:42

i try to connect i9060 show his error
plz tell all connection is ok as pinout

Quote:

================================================== ====
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

ERROR: EMMC IS NOT Ready! (CMD1)
Try to Adjust VCCIO Voltage
CMD1 Reply: 0xFFFFFFFF

Interface Reset OK!
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 2.6-2.7V
2.5-3.6V, 2.4-2.5V, 2.3-2.4V, 2.2-2.3V, 2.1-2.2V
2.0-2.1V, 1.9-2.0V, 1.8-1.9V, 1.7-1.8V, 1.65-1.7V
1.60-1.65V, 1.55-1.60V, 1.50-1.55V, 1.45-1.50V

CID : FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
ERROR: EMMC_ALL_SEND_CID FAILED (CMD2)
Check your Test Point Soldering!
Try to Adjust VCCIO Voltage

ranagaurav · 12-27-2015, 07:10

here is some screen shot

ribut budiono · 12-27-2015, 07:29

look like emmc dead .need remove and repair via test point.

ranagaurav · 12-27-2015, 07:58

Quote:

look like emmc dead .need remove and repair via test point.

how to dead emmc phone is working well before worng flashing
phone i9060 i flash i9082 flash file so phone is dead

ribut budiono · 12-27-2015, 10:40

emmc firmware erased by wrong flashing .you need repair via test point

ranagaurav · 12-28-2015, 07:18

any other solution without remove emmc in board

ranagaurav · 12-28-2015, 07:18

why not reply atf team where r u ?

**chand_gee** · 12-28-2015, 14:56

Quote:

Originally Posted by ranagaurav

why not reply atf team where r u ?

follow this post
all required files are attached
use volts same like i mention in picture
http://forum.gsmhosting.com/vbb/f609...-done-1975650/

ranagaurav · 01-01-2016, 09:18

same i do as u mentiond but not done

12-23-2015, 15:16	#1 (permalink)
ranagaurav No Life Poster Join Date: Nov 2008 Location: gsm hosting Posts: 5,609 Member: 907098 Status: Offline Sonork: 100.1601140 Thanks Meter: 705	need boot1 boot2 and user area i9060 phone dead during wrong flash file i try to boot repair found emmc pinout but cant found boot1& boot2 or user area file so plz rewqust to supporter plz provide i w8 kindy relpy

12-27-2015, 07:10	#3 (permalink)
ranagaurav No Life Poster Join Date: Nov 2008 Location: gsm hosting Posts: 5,609 Member: 907098 Status: Offline Sonork: 100.1601140 Thanks Meter: 705	here is some screen shot

12-27-2015, 07:29	#4 (permalink)
ribut budiono Freak Poster Join Date: Apr 2007 Location: malang indonesia Posts: 133 Member: 480385 Status: Offline Thanks Meter: 16	look like emmc dead .need remove and repair via test point.

12-27-2015, 10:40	#6 (permalink)
ribut budiono Freak Poster Join Date: Apr 2007 Location: malang indonesia Posts: 133 Member: 480385 Status: Offline Thanks Meter: 16	emmc firmware erased by wrong flashing .you need repair via test point

12-28-2015, 07:18	#7 (permalink)
ranagaurav No Life Poster Join Date: Nov 2008 Location: gsm hosting Posts: 5,609 Member: 907098 Status: Offline Sonork: 100.1601140 Thanks Meter: 705	any other solution without remove emmc in board

12-28-2015, 07:18	#8 (permalink)
ranagaurav No Life Poster Join Date: Nov 2008 Location: gsm hosting Posts: 5,609 Member: 907098 Status: Offline Sonork: 100.1601140 Thanks Meter: 705	why not reply atf team where r u ?

01-01-2016, 09:18	#10 (permalink)
ranagaurav No Life Poster Join Date: Nov 2008 Location: gsm hosting Posts: 5,609 Member: 907098 Status: Offline Sonork: 100.1601140 Thanks Meter: 705	same i do as u mentiond but not done