Repaire nokia lumia 610 NFC

[ZiDanRO]

I have tried to flash the firmware but i get errors with AMSS partition (i don't have right now the log but the advice for that errors was repaire boot with TP)

then tried to repaire with TP conection and i get this:

================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.


Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010030303847344200D75A69DB6FB3
CSD : D00E00320F5903FFFFFFFFE79640001F

eMMC Boot Information
Revision 1.5 (for MMC v4.41)
BOOT PARTITION : USER AREA
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 3584 KB
HC ERASE GROUP SIZE: 4096 KB
USER AREA SIZE : 7952400384 BYTES
BOOT PARTITION SIZE: 2048 KB
RPMB PARTITION SIZE: 256 KB

Lumia 610/610C Detected

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 008G4B
Product Rev : 0.0
Product SN : D75A69DB
Manufactured : January 2012

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 3 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010030303847344200D75A69DB6FB3.ext_csd
Backup Directory:
D:\Boxuri\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

Writing MBR...
Write Success!
Writing DBL...
Block Write CRC Error 0x01
5E
Write Block Error
Block Write CRC Error 0x01
5E
ERROR: Block Write Failed at 0x00000007
Check your Test Point Soldering!
ERROR: WRITE FAILED!

Total Elapsed Time 00:00:08

[ZiDanRO]

It is totaly dead or is still hope for him?

This was the error on flashing:

Windows Phone Lumia Flasher
================================================== ====

If the Phone is ALIVE
1. Power On the Phone and Connect it to the USB Port

If the Phone is DEAD
1. Press and Hold the VOLUME UP button
2. Connect it to the USB Port while still Pressing
the VOLUME UP button
3. Continue to Press the VOLUME UP button for 8 more
seconds
================================================== ====


ERROR: Data Rejected at SEQ 0x1

ERROR: Data Rejected at SEQ 0x2

Sending AMSS Certificate
HASH: 0BFDF05E7010650600450D156BFA520A430159E9
Certificate Size: 449 Bytes

ERROR: Data Rejected at SEQ 0x3
Status : WRITE AMSS CERTIFICATE FAILED

[ZiDanRO]

No opinions for this problem?

[ZiDanRO]

Any hope with this problem?

[Advance-Box]

Originally Posted by ZiDanRO

Any hope with this problem?

This phone has damaged KEYSTORE and possible bad IMEI.

You can fix it using Chimera Tool I think...

but you cannot fix it with ATF because we do not touch IMEI part of Lumia 610.