Samsung SM-J700F/H/K/M/P/8 BOOT Repair via eMMC Flashing - Page 17 - GSM-Forum

>>PakFones<< · 05-04-2016, 11:27

Thanks for reporting the file link can be found below Remove space from link.

w w w . s a m m o b i l e.com/firmwares/download/70263/J700FXXU2APD6_J700FOJV2APD1_TUR/

zulfqarali · 05-05-2016, 16:11

Quote:

Originally Posted by allumts

@zulfqarali,

Where's the second resistor?

sir i cant underrstant about 2nd resistor

In Adapter are 2 Resistor of 100 Ohms

sir i cannt understand also these 2 resister of 100 ohms in adapter please help me step by step
From V.3.3 to Data0 and CMD, you connection is WRONG.

sir on my board resistance between data and v2.8 is misssing then iput 100ohms resistance between cmd and v2.8 then i write file of diffrent versions writing is succes but set is still dead if im wrong then plzzzz kindly help me

Why you write all these partition lol? Only Cm.bin and Sboot.bin as Boot1 and Boot2 are enough.

Why not read carefully prvious page?...Modific all and report here you Success.

BR
allumts

sir please tell me about this it is right or wrong ??

(When i Press Power Button Continously Then File Write Properly And When i Release Power Button Then file writing Process is Stoped)

i tried also v2.8 & v3.3 set conecting is ok

v2,8 write file done this ver file-J700HXXU1AOK5_J700HOJV1AOK6_J700HXXU1AOK8_HOME.tar

& use this ver file..

SM-J700Hver 5.1.1--1_20160115111040_vrbiyt9hvt_fac
SM-J700H_ 1_20160115111040_vrbiyt9hvt_fac
J700HXXU1AOG9_J700HOJV1AOGA
J700HXXU1AOFG_OXY1AOFG
J700HXXU1AOK5_J700HOJV1AOK6_J700HXXU1AOK8_HOME.tar
J700HXXU1AOJ5_J700HOJV1AOI1_J700HXXU1AOJ5_HOME.tar
BL_J700HXXU1APA3

Plz Sir Corrcet Ver & Guide Me Step By Step

Br.
JAMIL MOBILE

hema2222 · 05-07-2016, 22:09

sam problem with me any solution

hema2222 · 05-07-2016, 22:33

when i try to repair sm-j700f dead boot repair showing pit error.

================================================== ===
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010034303030373300A35A25EFA22F
CSD : D07E00320F5903FFFFFFFFE78A4000D1

eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 400073
Product Rev : 0.0
Product SN : A35A25EF
Manufactured : January 1999

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 8000 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...
ERROR: PIT Partition NOT FOUND!
Please Provide a PIT File via Selecting "Re-Partition"

when i try with pit again show another error
Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...

Start Writing Flash Images...

Flash Image: MBR + PGPT
Start Writing 0x00000032 Blocks at 0x00000000
Partition Selected: USER AREA
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!

hema2222 · 05-07-2016, 22:34

when i try to repair sm-j700f dead boot repair showing pit error.

================================================== ===
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010034303030373300A35A25EFA22F
CSD : D07E00320F5903FFFFFFFFE78A4000D1

eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 400073
Product Rev : 0.0
Product SN : A35A25EF
Manufactured : January 1999

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 8000 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...
ERROR: PIT Partition NOT FOUND!
Please Provide a PIT File via Selecting "Re-Partition"

when i try with pit again show another error
Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...

Start Writing Flash Images...

Flash Image: MBR + PGPT
Start Writing 0x00000032 Blocks at 0x00000000
Partition Selected: USER AREA
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
Report Post

any solution plzplzplz

allumts · 05-07-2016, 23:07

Quote:

Originally Posted by hema2222

when i try to repair sm-j700f dead boot repair showing pit error.

================================================== ===
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010034303030373300A35A25EFA22F
CSD : D07E00320F5903FFFFFFFFE78A4000D1

eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 400073
Product Rev : 0.0
Product SN : A35A25EF
Manufactured : January 1999

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 8000 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...
ERROR: PIT Partition NOT FOUND!
Please Provide a PIT File via Selecting "Re-Partition"

when i try with pit again show another error
Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...

Start Writing Flash Images...

Flash Image: MBR + PGPT
Start Writing 0x00000032 Blocks at 0x00000000
Partition Selected: USER AREA
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
Report Post

any solution plzplzplz

Try with this PIT: EXYNOS_7_OCTA_7580

Br
allumts

muhammad.arif09 · 05-08-2016, 09:52

where is emmc master
mr
chand_gee theise days any one now he is offline sincs 2 month
i need to talk

hema2222 · 05-08-2016, 22:21

sam proplem
help plz plz plz

hema2222 · 05-09-2016, 16:10

when i try to repair sm-j700f dead boot repair showing pit error.

================================================== ===
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010034303030373300A35A25EFA22F
CSD : D07E00320F5903FFFFFFFFE78A4000D1

eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 400073
Product Rev : 0.0
Product SN : A35A25EF
Manufactured : January 1999

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 8000 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...
ERROR: PIT Partition NOT FOUND!
Please Provide a PIT File via Selecting "Re-Partition"

when i try with pit again show another error
Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...

Start Writing Flash Images...

Flash Image: MBR + PGPT
Start Writing 0x00000032 Blocks at 0x00000000
Partition Selected: USER AREA
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
Report Post

any solution plzplzplz

hema2222 · 05-09-2016, 18:49

when i try to repair sm-j700h dead boot repair showing pit error.

================================================== ===
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010034303030373300A35A25EFA22F
CSD : D07E00320F5903FFFFFFFFE78A4000D1

eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 400073
Product Rev : 0.0
Product SN : A35A25EF
Manufactured : January 1999

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 8000 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...
ERROR: PIT Partition NOT FOUND!
Please Provide a PIT File via Selecting "Re-Partition"

when i try with pit again show another error
Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...

Start Writing Flash Images...

Flash Image: MBR + PGPT
Start Writing 0x00000032 Blocks at 0x00000000
Partition Selected: USER AREA
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
Report Post

any solution plzplzplz

uiuiy · 05-09-2016, 21:58

Quote:

Originally Posted by hema2222

when i try to repair sm-j700h dead boot repair showing pit error.

================================================== ===
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 11010034303030373300A35A25EFA22F
CSD : D07E00320F5903FFFFFFFFE78A4000D1

eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB

eMMC Device Information
Manufacturer ID: TOSHIBA
Device Type : Embedded BGA
Application ID : 00
Product Name : 400073
Product Rev : 0.0
Product SN : A35A25EF
Manufactured : January 1999

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 8000 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...
ERROR: PIT Partition NOT FOUND!
Please Provide a PIT File via Selecting "Re-Partition"

when i try with pit again show another error
Extended CSD Saved:
11010034303030373300A35A25EFA22F.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

MBR is Corrupted...

Start Writing Flash Images...

Flash Image: MBR + PGPT
Start Writing 0x00000032 Blocks at 0x00000000
Partition Selected: USER AREA
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
R1b Timeout Error!
Report Post

any solution plzplzplz

hi
used latest firmware in live.samsung-updates.com and set speed on 2.5mh

uiuiy · 05-09-2016, 22:04

hi
i direct my j700h and repair with sboot and cm only with this firmware "SER-J700HXXU2APC5-20160406233018_2" my phone powerd on and came downloading screen i flash it with same firmware it came on samsung logo and dead again and never powerd on and i can not direct again (in first time after power my phone amper was 25/100 and second time is 25/100)
please hellp me
thx

hema2222 · 05-10-2016, 22:55

sam proplem
plas help
plz plz plz

aleksa55 · 05-11-2016, 16:44

Quote:

Originally Posted by alamgir80

can i use this pinout ?
or must need ATF JTAG PLUS ATF 4 IN 1 ADAPTOR
I have only atf big box. don't have adapter.

I have only atf big box

can u help me wit connections

allumts · 05-11-2016, 18:24

And not see that this connection is for Atf Big from RJ45 cable?

More clear of this @X-Shadow cannot post, and you ask for connection...

05-04-2016, 11:27	#241 (permalink)
>>PakFones<< No Life Poster Join Date: Jul 2007 Location: My Computer Posts: 1,308 Member: 553178 Status: Offline Sonork: 100.1592454 Thanks Meter: 957	Thanks for reporting the file link can be found below Remove space from link. w w w . s a m m o b i l e.com/firmwares/download/70263/J700FXXU2APD6_J700FOJV2APD1_TUR/

05-07-2016, 22:09	#243 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	sam problem with me any solution

05-07-2016, 22:33	#244 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	when i try to repair sm-j700f dead boot repair showing pit error. ================================================== === ================================================== ==== eMMC Test Point Connection Module ================================================== ==== ================================================== ==== 1. DO NOT USE THE PHONE"S BATTERY 2. Connect the Soldered TP Connections to ATF Box 3. Disconnect the USB Cable and Wait until the the ATF Software will tell you to Connect the USB. Interface Reset OK! eMMC Access Type: SECTOR MODE eMMC Supported Voltage Range: 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V 3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V CID : 11010034303030373300A35A25EFA22F CSD : D07E00320F5903FFFFFFFFE78A4000D1 eMMC Boot Information Revision 1.0 (for MMC v4.0) BOOT PARTITION : NOT BOOT ENABLED PARTITION ACCESS : R/W USER PARTITION PERM_BOOT_CFG_PROT : DISABLED PWR_BOOT_CFG_PROT : DISABLED BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED RESET BUS WIDTH : ENABLED eMMC FirmW UPDATE : DISABLED EMMC CACHE SIZE : 0 KB SUPER PAGE SIZE : 0 KB HC ERASE GROUP SIZE: 0 KB USER AREA SIZE : 0 BYTES BOOT PARTITION SIZE: 0 KB RPMB PARTITION SIZE: 0 KB eMMC Device Information Manufacturer ID: TOSHIBA Device Type : Embedded BGA Application ID : 00 Product Name : 400073 Product Rev : 0.0 Product SN : A35A25EF Manufactured : January 1999 Card Specific Data CSD_STRUCTURE : Extended SPEC_VERS : Version 4.1/4.2/4.3 TAAC : 8000 ns TRAN_SPEED : 4000000 KHz READ_BL_LEN : 512 Bytes C_SIZE : HIGH CAPACITY WP_GRP_ENABLE : YES WRITE_BL_LEN : 512 Bytes CONTENT_PROT_APP : NO PERM_WRITE_PROTECT: NO TMP_WRITE_PROTECT : NO Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... ERROR: PIT Partition NOT FOUND! Please Provide a PIT File via Selecting "Re-Partition" when i try with pit again show another error Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... Start Writing Flash Images... Flash Image: MBR + PGPT Start Writing 0x00000032 Blocks at 0x00000000 Partition Selected: USER AREA R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! R1b Timeout Error!

05-07-2016, 22:34	#245 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	when i try to repair sm-j700f dead boot repair showing pit error. ================================================== === ================================================== ==== eMMC Test Point Connection Module ================================================== ==== ================================================== ==== 1. DO NOT USE THE PHONE"S BATTERY 2. Connect the Soldered TP Connections to ATF Box 3. Disconnect the USB Cable and Wait until the the ATF Software will tell you to Connect the USB. Interface Reset OK! eMMC Access Type: SECTOR MODE eMMC Supported Voltage Range: 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V 3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V CID : 11010034303030373300A35A25EFA22F CSD : D07E00320F5903FFFFFFFFE78A4000D1 eMMC Boot Information Revision 1.0 (for MMC v4.0) BOOT PARTITION : NOT BOOT ENABLED PARTITION ACCESS : R/W USER PARTITION PERM_BOOT_CFG_PROT : DISABLED PWR_BOOT_CFG_PROT : DISABLED BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED RESET BUS WIDTH : ENABLED eMMC FirmW UPDATE : DISABLED EMMC CACHE SIZE : 0 KB SUPER PAGE SIZE : 0 KB HC ERASE GROUP SIZE: 0 KB USER AREA SIZE : 0 BYTES BOOT PARTITION SIZE: 0 KB RPMB PARTITION SIZE: 0 KB eMMC Device Information Manufacturer ID: TOSHIBA Device Type : Embedded BGA Application ID : 00 Product Name : 400073 Product Rev : 0.0 Product SN : A35A25EF Manufactured : January 1999 Card Specific Data CSD_STRUCTURE : Extended SPEC_VERS : Version 4.1/4.2/4.3 TAAC : 8000 ns TRAN_SPEED : 4000000 KHz READ_BL_LEN : 512 Bytes C_SIZE : HIGH CAPACITY WP_GRP_ENABLE : YES WRITE_BL_LEN : 512 Bytes CONTENT_PROT_APP : NO PERM_WRITE_PROTECT: NO TMP_WRITE_PROTECT : NO Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... ERROR: PIT Partition NOT FOUND! Please Provide a PIT File via Selecting "Re-Partition" when i try with pit again show another error Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... Start Writing Flash Images... Flash Image: MBR + PGPT Start Writing 0x00000032 Blocks at 0x00000000 Partition Selected: USER AREA R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! Report Post any solution plzplzplz

05-08-2016, 09:52	#247 (permalink)
muhammad.arif09 Freak Poster Join Date: Jun 2013 Location: Dubai UAE Posts: 374 Member: 1951379 Status: Offline Sonork: 100.1647567 Thanks Meter: 148	where is emmc master mr chand_gee theise days any one now he is offline sincs 2 month i need to talk

05-08-2016, 22:21	#248 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	sam proplem help plz plz plz

05-09-2016, 16:10	#249 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	when i try to repair sm-j700f dead boot repair showing pit error. ================================================== === ================================================== ==== eMMC Test Point Connection Module ================================================== ==== ================================================== ==== 1. DO NOT USE THE PHONE"S BATTERY 2. Connect the Soldered TP Connections to ATF Box 3. Disconnect the USB Cable and Wait until the the ATF Software will tell you to Connect the USB. Interface Reset OK! eMMC Access Type: SECTOR MODE eMMC Supported Voltage Range: 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V 3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V CID : 11010034303030373300A35A25EFA22F CSD : D07E00320F5903FFFFFFFFE78A4000D1 eMMC Boot Information Revision 1.0 (for MMC v4.0) BOOT PARTITION : NOT BOOT ENABLED PARTITION ACCESS : R/W USER PARTITION PERM_BOOT_CFG_PROT : DISABLED PWR_BOOT_CFG_PROT : DISABLED BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED RESET BUS WIDTH : ENABLED eMMC FirmW UPDATE : DISABLED EMMC CACHE SIZE : 0 KB SUPER PAGE SIZE : 0 KB HC ERASE GROUP SIZE: 0 KB USER AREA SIZE : 0 BYTES BOOT PARTITION SIZE: 0 KB RPMB PARTITION SIZE: 0 KB eMMC Device Information Manufacturer ID: TOSHIBA Device Type : Embedded BGA Application ID : 00 Product Name : 400073 Product Rev : 0.0 Product SN : A35A25EF Manufactured : January 1999 Card Specific Data CSD_STRUCTURE : Extended SPEC_VERS : Version 4.1/4.2/4.3 TAAC : 8000 ns TRAN_SPEED : 4000000 KHz READ_BL_LEN : 512 Bytes C_SIZE : HIGH CAPACITY WP_GRP_ENABLE : YES WRITE_BL_LEN : 512 Bytes CONTENT_PROT_APP : NO PERM_WRITE_PROTECT: NO TMP_WRITE_PROTECT : NO Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... ERROR: PIT Partition NOT FOUND! Please Provide a PIT File via Selecting "Re-Partition" when i try with pit again show another error Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... Start Writing Flash Images... Flash Image: MBR + PGPT Start Writing 0x00000032 Blocks at 0x00000000 Partition Selected: USER AREA R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! Report Post any solution plzplzplz

05-09-2016, 18:49	#250 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	when i try to repair sm-j700h dead boot repair showing pit error. ================================================== === ================================================== ==== eMMC Test Point Connection Module ================================================== ==== ================================================== ==== 1. DO NOT USE THE PHONE"S BATTERY 2. Connect the Soldered TP Connections to ATF Box 3. Disconnect the USB Cable and Wait until the the ATF Software will tell you to Connect the USB. Interface Reset OK! eMMC Access Type: SECTOR MODE eMMC Supported Voltage Range: 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V 3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V CID : 11010034303030373300A35A25EFA22F CSD : D07E00320F5903FFFFFFFFE78A4000D1 eMMC Boot Information Revision 1.0 (for MMC v4.0) BOOT PARTITION : NOT BOOT ENABLED PARTITION ACCESS : R/W USER PARTITION PERM_BOOT_CFG_PROT : DISABLED PWR_BOOT_CFG_PROT : DISABLED BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED RESET BUS WIDTH : ENABLED eMMC FirmW UPDATE : DISABLED EMMC CACHE SIZE : 0 KB SUPER PAGE SIZE : 0 KB HC ERASE GROUP SIZE: 0 KB USER AREA SIZE : 0 BYTES BOOT PARTITION SIZE: 0 KB RPMB PARTITION SIZE: 0 KB eMMC Device Information Manufacturer ID: TOSHIBA Device Type : Embedded BGA Application ID : 00 Product Name : 400073 Product Rev : 0.0 Product SN : A35A25EF Manufactured : January 1999 Card Specific Data CSD_STRUCTURE : Extended SPEC_VERS : Version 4.1/4.2/4.3 TAAC : 8000 ns TRAN_SPEED : 4000000 KHz READ_BL_LEN : 512 Bytes C_SIZE : HIGH CAPACITY WP_GRP_ENABLE : YES WRITE_BL_LEN : 512 Bytes CONTENT_PROT_APP : NO PERM_WRITE_PROTECT: NO TMP_WRITE_PROTECT : NO Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... ERROR: PIT Partition NOT FOUND! Please Provide a PIT File via Selecting "Re-Partition" when i try with pit again show another error Extended CSD Saved: 11010034303030373300A35A25EFA22F.ext_csd Backup Directory: C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\ MBR is Corrupted... Start Writing Flash Images... Flash Image: MBR + PGPT Start Writing 0x00000032 Blocks at 0x00000000 Partition Selected: USER AREA R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! R1b Timeout Error! Report Post any solution plzplzplz

05-09-2016, 22:04	#252 (permalink)
uiuiy Insane Poster Join Date: Apr 2012 Location: IRAN-Yazd Posts: 94 Member: 1743808 Status: Offline Thanks Meter: 6	hi i direct my j700h and repair with sboot and cm only with this firmware "SER-J700HXXU2APC5-20160406233018_2" my phone powerd on and came downloading screen i flash it with same firmware it came on samsung logo and dead again and never powerd on and i can not direct again (in first time after power my phone amper was 25/100 and second time is 25/100) please hellp me thx

05-10-2016, 22:55	#253 (permalink)
hema2222 Junior Member Join Date: May 2008 Posts: 20 Member: 777714 Status: Offline Thanks Meter: 0	sam proplem plas help plz plz plz

05-11-2016, 18:24	#255 (permalink)
allumts No Life Poster Join Date: Apr 2011 Age: 58 Posts: 16,408 Member: 1564612 Status: Offline Thanks Meter: 12,343	And not see that this connection is for Atf Big from RJ45 cable? More clear of this @X-Shadow cannot post, and you ask for connection...