3GS 109B, Wites can you reply to this - GSM-Forum

joeshannallie · 08-07-2012, 08:04

I removed the 109B IC with no problem I thought. I noticed one of the very small ICs directly under came off also with one of the pads. It is R104. Is there a way around this> Please say yes. Wites can you please reply to this with a solution if there may be one. Also can advise on which way does the 109 sit back on the board? Thanks in advance for the help.

joeshannallie · 08-08-2012, 02:59

Come on now, Surely some of you guys have a answer for this. I really need a solution if there is one.

tinner105 · 08-09-2012, 07:43

I think you have to run a wire from the 109 to the lcd connector now.

URL=http://imageshack.us/photo/my-images/259/3gsbcklight.jpg/]

[/URL]

Tinner

and as far as the 109b ic placement..... the picture i posted you would be able to read the markings on it with the board in this position.

joeshannallie · 08-09-2012, 16:25

Thank you Tinner. I think I fried the board. I replaced the coil and 109 and put it back together and thought it may still work without the resistor and the pc recognized it as being in recovery mode and then it would not recognize it anymore. It would say a unrecognized device has been detected down by the clock where it pops up when you connect someting thru USB. Oh well I have another board coming that randomly restarts. Maybe I will get it going soon.

08-07-2012, 08:04	#1 (permalink)
joeshannallie Junior Member Join Date: Jul 2012 Posts: 13 Member: 1792061 Status: Offline Thanks Meter: 0	3GS 109B, Wites can you reply to this I removed the 109B IC with no problem I thought. I noticed one of the very small ICs directly under came off also with one of the pads. It is R104. Is there a way around this> Please say yes. Wites can you please reply to this with a solution if there may be one. Also can advise on which way does the 109 sit back on the board? Thanks in advance for the help.

08-09-2012, 07:43	#3 (permalink)
tinner105 Freak Poster Join Date: Jul 2010 Location: California Posts: 243 Member: 1352483 Status: Offline Thanks Meter: 24	solution I think you have to run a wire from the 109 to the lcd connector now. URL=http://imageshack.us/photo/my-images/259/3gsbcklight.jpg/][/URL] Tinner and as far as the 109b ic placement..... the picture i posted you would be able to read the markings on it with the board in this position.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
How can I do a Welcome note for my 6110 a dosn't have any one ?	Viper	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	06-27-2015 11:57
How to add a language in 51xx/61xx	tati	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	05-21-2013 19:20
How to upload a new firmware...	Brand	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	06-08-2012 18:29

08-08-2012, 02:59	#2 (permalink)
joeshannallie Junior Member Join Date: Jul 2012 Posts: 13 Member: 1792061 Status: Offline Thanks Meter: 0	Come on now, Surely some of you guys have a answer for this. I really need a solution if there is one.

08-09-2012, 16:25	#4 (permalink)
joeshannallie Junior Member Join Date: Jul 2012 Posts: 13 Member: 1792061 Status: Offline Thanks Meter: 0	Thank you Tinner. I think I fried the board. I replaced the coil and 109 and put it back together and thought it may still work without the resistor and the pc recognized it as being in recovery mode and then it would not recognize it anymore. It would say a unrecognized device has been detected down by the clock where it pops up when you connect someting thru USB. Oh well I have another board coming that randomly restarts. Maybe I will get it going soon.