Help needed for G'five BT01 - GSM-Forum

MTK CHIP · 04-29-2011, 14:52

Hello,

Here is the Log of the operation.

Quote:

COM18 [VCP0] selected
module v3.30
Device: Autodetect 6253 NOR
Checking data, wait...
Action: reset settings ("format ffs") NAND
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6253:8A02:8A00
status: FF
bbchip bl ver: FE
NOR flash id[00C0]: 0098:009E00000000 [TOSHIBA] TC58FYM7T8C
chip size: 16Mb
otp status/size: S_DA_NOR_OTP_EXIST/00020000
NAND flash chip: not installed
internal RAM size: 00020000
external RAM: S_DA_RAM_ERROR
done
Set baudrate (115200)...
done
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===> detect existing firmware structure...
detect ffs...
detect sec ro...
detect custom parameters...
detect project-id...
detect NOR info...
number of areas/bytes to read: 1:00040000
reading (HW_STORAGE_NOR)...
error: can not read memory: 0FAA:S_FT_READBACK_FAIL
can not read memory, errorcode: 0FAA
it may be problem with current operation
error: last error: 0FAA:S_FT_READBACK_FAIL
Disconnect...
done
Finished, time used: 1 min 4 sec
Remove/Install battery now !

phone come to stuck on logo. Now phone is dead
Taken action -
First try to ffs with Autodetected 6205-6239 NOR mode
but is show

Quote:

COM18 [VCP0] selected
module v3.30
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: reset settings ("format ffs")
ffs/eeprom backup enabled, it may takes several minutes !
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6253:8A02:8A00]...
CPU: MT6253
high speed boot On
chip: 0000:0000:000F
status: FF
Select another CPU type [6253] and try again !
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 16 sec
Remove/Install battery now !

PASSIONATE_BOYS · 04-29-2011, 15:02

Try to read detailed info and then flash the phone with same version.

Wr.

MTK CHIP · 04-29-2011, 15:16

Quote:

Originally Posted by PASSIONATE_BOYS

Try to read detailed info and then flash the phone with same version.

Wr.

Read detailed info...

Quote:

COM18 [VCP0] selected
module v3.30
Device: Autodetect 6253 NOR
Checking data, wait...
advanced flash detection disabled
Action: read/check information
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6253:8A02:8A00]...
CPU: MT6253
high speed boot On
chip: 0000:0000:000F
status: FF
boot packet size: 0400
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 11 sec
Remove/Install battery now !

Read firmware

Quote:

COM18 [VCP0] selected
module v3.30
Device: Autodetect 6253 NOR
Checking data, wait...
Action: read firmware NAND
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6253:8A02:8A00
status: FF
bbchip bl ver: FE
NOR flash id[00C0]: 0098:009E00000000 [TOSHIBA] TC58FYM7T8C
chip size: 16Mb
otp status/size: S_DA_NOR_OTP_EXIST/00020000
NAND flash chip: not installed
internal RAM size: 00020000
external RAM: S_DA_RAM_ERROR
done
Set baudrate (115200)...
done
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===> detect existing firmware structure...
detect ffs...
detect sec ro...
detect custom parameters...
detect project-id...
detect NOR info...
number of areas/bytes to read: 1:00040000
reading (HW_STORAGE_NOR)...
error: can not read memory: 0FAA:S_FT_READBACK_FAIL
can not read memory, errorcode: 0FAA
it may be problem with current operation
error: last error: 0FAA:S_FT_READBACK_FAIL
Disconnect...
done
Finished, time used: 1 min 38 sec
Remove/Install battery now !

InfinityHelp · 04-29-2011, 22:05

hello!

which cable/box do you use as interface?

MTK CHIP · 04-30-2011, 07:54

I use Infinity as Interface. and i use manually cable (3 point soldering cable Rx/Tx/Gnd)for connecting.

MTK CHIP · 04-30-2011, 15:03

Infinity team need ur reply ASAP.

InfinityHelp · 04-30-2011, 22:07

hello!

i have no idea what could be reason for this.
Try to slightly heat CPU and Flash IC

MTK CHIP · 05-02-2011, 08:42

Quote:

Originally Posted by InfinityHelp

hello!

i have no idea what could be reason for this.
Try to slightly heat CPU and Flash IC

Problem is not in hardware bro.
I solve the problem using Autodetected 6205-6239 NAND mode.

Here is the successful FFS log & Readed full flash.

Quote:

COM18 [VCP0] selected
module v3.30
Device: Autodetect 6228-6268 NAND
Checking data, wait...
Action: read firmware NAND
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6253:8A02:8A00
status: FF
bbchip bl ver: FE
NOR flash id[00C0]: 0098:009E00000000 [TOSHIBA] TC58FYM7T8C
chip size: 16Mb
otp status/size: S_DA_NOR_OTP_EXIST/00020000
NAND flash chip: not installed
internal RAM size: 00020000
external RAM: S_DA_RAM_ERROR
done
Set baudrate (460800)...
done
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===> detect existing firmware structure...
detect ffs...
ffs offset/size: 00000000/00000000
detect sec ro...
detect custom parameters...
detect project-id...
project-id: L5AMM07.9.52.1.3T05M1126_M700
detect NOR info...
number of areas/bytes to read: 1:00040000
reading (HW_STORAGE_NOR)...
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
startup code area #1 detection done
rom info ver: 07
sw version: JWT_Z900B_002_PCB01_GPRS_MT6253_S00.L5AMM07_9_52_1 _3T05M1126_M700.BIN
project-id: L5AMM07.9.52.1.3T05M1126_M700, 00000000
code offset: 00000000
ffs offset/size [02]: 00E00000/00200000
rom info structure: [standard] type (07)
TCL-ID is absent
===> done
====================
New firmware found (v.3.30, database date: 26.04.2011):
JWT_Z900B_002_PCB01_GPRS_MT6253_S00.L5AMM07_9_52_1 _3T05M1126_M700.BIN

This firmware is missing in support area. If this phone is good and working:

- download latest software from support area and try again, probably this firmware already supported in latest software
- make "Read full flash" operation
- send flash backup files to support: [email protected] or upload files to RapidShare AG, Cham, Switzerland or 4shared.com - free file sharing and storage
- include in your e-mail full text from phone back label (phone name etc.)
====================
area size: 14Mb
number of areas/bytes to read: 1:00E00000
reading (HW_STORAGE_NOR)...
file saved: C:\Documents and Settings\Administrator\Desktop\JWT_Z900B_002_PCB01 _GPRS_MT6253_S00.L5AMM07_9_52_1_3T05M1126_M700__fi rmware_20110502-130446.B0M.bin
Disconnect...
done
Finished, time used: 11 min 20 sec
Remove/Install battery now !

NEW FIRMWARE UPLOADED ON RAPIDSHARE-
JWT_Z900B_002_PCB01_GPRS_MT6253_S00.L5AMM07_9_52_1 _3T05M1126_M700.BIN

https://rapidshare.com/files/4602009...130446.B0M.bin
(Download this file from here i don't send this link to [email protected])

YellowBoss · 05-02-2011, 11:33

As I can understand it's a backup from damaged phone.
Or it is strated to work correctly after format FFS?

MTK CHIP · 05-02-2011, 12:15

Quote:

Originally Posted by YellowBoss

As I can understand it's a backup from damaged phone.
Or it is strated to work correctly after format FFS?

Yes u r right.

After power on the set after 1 hour set goes to dead automatically.
now i heat the phone CPU & flash IC. (may be it work good)

Post result ASAP.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
need ericsson 88 cable	migdamas	Old Ericsson Phones & Sony Phones	2	03-24-2017 16:24
Need software upgrade for Nokia 5110	ptkrf	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	30	02-24-2016 10:21
Help with 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	05-25-2009 16:29
need eeprom photo????	mobileinfo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	05-26-1999 11:35

04-29-2011, 15:02	#2 (permalink)
PASSIONATE_BOYS No Life Poster Join Date: Jul 2007 Location: Infinity-Box Support- Posts: 9,321 Member: 541591 Status: Offline Sonork: 100.1611509 Thanks Meter: 7,361	Try to read detailed info and then flash the phone with same version. Wr.

04-29-2011, 22:05	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! which cable/box do you use as interface?

04-30-2011, 07:54	#5 (permalink)
MTK CHIP Freak Poster Join Date: Mar 2010 Location: In Search of free BB5 rpl Posts: 468 Member: 1248595 Status: Offline Sonork: 100.1607313 Thanks Meter: 99	I use Infinity as Interface. and i use manually cable (3 point soldering cable Rx/Tx/Gnd)for connecting.

04-30-2011, 15:03	#6 (permalink)
MTK CHIP Freak Poster Join Date: Mar 2010 Location: In Search of free BB5 rpl Posts: 468 Member: 1248595 Status: Offline Sonork: 100.1607313 Thanks Meter: 99	Infinity team need ur reply ASAP.

04-30-2011, 22:07	#7 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! i have no idea what could be reason for this. Try to slightly heat CPU and Flash IC

05-02-2011, 11:33	#9 (permalink)
YellowBoss Product Supporter Join Date: Jun 2009 Location: private Posts: 36,458 Member: 1043909 Status: Offline Thanks Meter: 60,926	As I can understand it's a backup from damaged phone. Or it is strated to work correctly after format FFS?