boot repair problem - GSM-Forum

mobitechnepal · 05-25-2012, 09:12

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung i9100 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - IGNORED!
Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Flashing the dead body...
WARNING: Programming Error (0x25) at 0x000000000000 is handled as Cut Excess.
ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF <> 0x010000) plz help

mobitechnepal · 05-25-2012, 10:09

Detected dead body ID: 0x4BA00477 - IGNORED! means ??????

**legija** · 05-25-2012, 11:14

RIFF JTAG Box FAQ - ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF 0x010000)

05-25-2012, 09:12	#1 (permalink)
mobitechnepal Freak Poster Join Date: Oct 2009 Location: nepal,kathmandu,ason Posts: 420 Member: 1139381 Status: Offline Sonork: 1593399 Thanks: 634 Thanked 178 Times in 103 Posts	boot repair problem Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung i9100 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - IGNORED! Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Flashing the dead body... WARNING: Programming Error (0x25) at 0x000000000000 is handled as Cut Excess. ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF <> 0x010000) plz help

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Sim card sleep mode problem with 6130	ratzfatz	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	4	05-22-2012 11:13
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	3	11-21-1999 18:43
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	09-11-1999 17:39
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	07-16-1999 00:44

05-25-2012, 10:09	#2 (permalink)
mobitechnepal Freak Poster Join Date: Oct 2009 Location: nepal,kathmandu,ason Posts: 420 Member: 1139381 Status: Offline Sonork: 1593399 Thanks: 634 Thanked 178 Times in 103 Posts	Detected dead body ID: 0x4BA00477 - IGNORED! means ??????

05-25-2012, 11:14	#3 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 44 Posts: 4,508 Member: 256342 Status: Offline Sonork: 100.45940 Thanks: 127 Thanked 23,892 Times in 1,926 Posts	RIFF JTAG Box FAQ - ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF 0x010000)