e1550 problem - GSM-Forum

Triminity · 09-08-2011, 07:01

I have new e1550 for unlock , tried to ressurection but fail. here is log.

open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [USB Modem E1550]

Connecting to the dead body...OK
Detected dead body ID: 0x401200E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at
Resurrection sequence started.
Establish communication with the phone...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x00A1 (128MB)
Detected: 128MB Revision.
Flashing the dead body...
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Stopped due to multiple communication errors. Terminating at 0x0000200000
[FINISH OPERATION_ID = RESURRECT]

always stops at 12%.
help needed.

ren77 · 09-08-2011, 07:21

Try to change Adaptive Clocking RTCK Sampling to 1Mhz to 5MHz and post results here.

Triminity · 09-08-2011, 07:23

thanks for reply.

same problem for every option.

ren77 · 09-08-2011, 08:39

Usually if this error occurs is because the frequency is so high, so you need to lower down the frequency. Please try again with lower frequency and post full log here.

09-08-2011, 07:01	#1 (permalink)
Triminity Registered User Join Date: Jun 2005 Location: jamnagar gujarat india Posts: 904 Member: 149938 Status: Offline Thanks Meter: 47	e1550 problem I have new e1550 for unlock , tried to ressurection but fail. here is log. open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [USB Modem E1550] Connecting to the dead body...OK Detected dead body ID: 0x401200E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at Resurrection sequence started. Establish communication with the phone...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x00A1 (128MB) Detected: 128MB Revision. Flashing the dead body... ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Stopped due to multiple communication errors. Terminating at 0x0000200000 [FINISH OPERATION_ID = RESURRECT] always stops at 12%. help needed.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	10-16-2013 08:16
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-21-1999 19:43
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

09-08-2011, 07:21	#2 (permalink)
ren77 Product Supporter Join Date: May 2001 Posts: 672 Member: 4566 Status: Offline Sonork: 100.112355 Thanks Meter: 503	Try to change Adaptive Clocking RTCK Sampling to 1Mhz to 5MHz and post results here.

09-08-2011, 07:23	#3 (permalink)
Triminity Registered User Join Date: Jun 2005 Location: jamnagar gujarat india Posts: 904 Member: 149938 Status: Offline Thanks Meter: 47	thanks for reply. same problem for every option.

09-08-2011, 08:39	#4 (permalink)
ren77 Product Supporter Join Date: May 2001 Posts: 672 Member: 4566 Status: Offline Sonork: 100.112355 Thanks Meter: 503	Usually if this error occurs is because the frequency is so high, so you need to lower down the frequency. Please try again with lower frequency and post full log here.