ETS2225 - Successfully connected with riff but not able to flash - GSM-Forum

rahul_rocks3 · 05-22-2011, 21:49

ETS2225 - Successfully connected with riff but not able to flash

I have been able to connect ETS2225 with riff but I am not able to flash it.....

Actually I want to unlock it....can anyone help me out please

amit kanpur · 05-22-2011, 22:23

Quote:

Originally Posted by rahul_rocks3

ETS2225 - Successfully connected with riff but not able to flash

I have been able to connect ETS2225 with riff but I am not able to flash it.....

Actually I want to unlock it....can anyone help me out please

post ur screen shorts. and logs..................

rahul_rocks3 · 05-23-2011, 19:25

Quote:

Originally Posted by jagritisharma

post ur screen shorts. and logs..................

ok brother i will post it tomorrow

rahul_rocks3 · 05-24-2011, 10:27

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [QSC6XXX L36 D08]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
Model selected: QUALCOMM (NAND) - QSC6XXX L36 D08

Detected dead body ID: 0x220B10E1

rahul_rocks3 · 05-24-2011, 10:28

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [QSC6XXX L36 D08]

Restarting target (nRST Low then High)...OK

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [QSC6XXX L32 D08]

Getting EmbeddedICE-RT registers...OK
00 = 0xFFFFFFFF 08 = 0xFFFFFFFF 10 = 0xFFFFFFFF
01 = 0x00080008 09 = 0xFFFFFFFF 11 = 0x00080008
02 = 0x00080008 0A = 0xFFFFFFFF 12 = 0x7FFFDE7D
03 = 0xFFFFFFFF 0B = 0xFFFFFFFF 13 = 0xFFFFFFFF
04 = 0x00000008 0C = 0x00080008 14 = 0x00080008
05 = 0xFFFFFFFF 0D = 0x00080008 15 = 0x9B4FB49A
06 = 0xFFFFFFFF 0E = 0x00080008 16 = 0x0FF802F9
07 = 0xFFFFFFFF 0F = 0xFFFFFFFF 17 = 0xFFFFFFFF

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [QSC6XXX L32 D08]

Resetting target...OK
STATUS: Target is halted.

R0 = 0x00000000 R6 = 0x00002100 R12 = 0x000030E0
R1 = 0x00000C60 R7 = 0x000023A0 R13 = 0x00003350
R2 = 0x00001734 R8 = 0x00002648 R14 = 0x000035C0
R3 = 0x000019A8 R9 = 0x00002904 R15 = 0xFFFFFFEE
R4 = 0x00001C1C R10 = 0x00002BC4 CPSR = 0x00000F28
R5 = 0x00001E8C R11 = 0x00002E50

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [QSC60XX L18 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x220B10E1 - CORRECT!
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...FAILED
ERROR: Wrong response code from the RIFF Box: 0x45

**legija** · 05-24-2011, 10:45

Hi,

Post here pinout which You've used, please.

rahul_rocks3 · 05-24-2011, 15:16

Quote:

Originally Posted by legija

Hi,

Post here pinout which You've used, please.

kindly contact me on yahoo [email protected]

**legija** · 05-24-2011, 16:49

Quote:

Originally Posted by rahul_rocks3

kindly contact me on yahoo [email protected]

Sure, cant wait to contact someone via yahoo.

rahul_rocks3 · 05-24-2011, 17:36

Quote:

Originally Posted by legija

Sure, cant wait to contact someone via yahoo.

ok will wait for you

jaraganahali · 01-14-2013, 04:18

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.43
Selected Resurrector: [Huawei ETS2225 V1.00]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK

Detected dead body ID: 0x220B10E1
.................................................. ................................

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.43
Selected Resurrector: [Huawei ETS2225 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x220B10E1 - IGNORED!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x20010000000000000000000000400000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected a Not Initialized FLASH1 Chip, ID: 0x0000/0x0000 (16MB)

Writting FLASH1 memory from 0x000000000000 to 0x0000003FFFFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

tata indicom smart pco huawei ets 2225...unlock flash file in riff dump is 4 mb but here it is showing 16 mb...how??
plz help me..

M0YAL · 01-14-2013, 08:17

Chip, ID: 0x0000/0x0000

Flash Damage

jaraganahali · 01-14-2013, 11:50

Quote:

Originally Posted by M0YAL

Chip, ID: 0x0000/0x0000

Flash Damage

but sir, first time i flash using unlock dump by selecting huawei ets2225 dll ..how it can be damage? any reason sir..

jaraganahali · 01-18-2013, 14:12

somebody help me to find out the flash chip on huawei ets2225 so that i can change the damage chip . if possible kindly help me with picture..

jaraganahali · 01-18-2013, 17:51

Quote:

Originally Posted by jaraganahali

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.43
Selected Resurrector: [Huawei ETS2225 V1.00]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK

Detected dead body ID: 0x220B10E1
.................................................. ................................

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.43
Selected Resurrector: [Huawei ETS2225 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x220B10E1 - IGNORED!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x20010000000000000000000000400000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected a Not Initialized FLASH1 Chip, ID: 0x0000/0x0000 (16MB)

Writting FLASH1 memory from 0x000000000000 to 0x0000003FFFFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

tata indicom smart pco huawei ets 2225...unlock flash file in riff dump is 4 mb but here it is showing 16 mb...how??
plz help me..

dear sir, my above problem may be because of this? kindly check the attchment ( photo)

05-22-2011, 21:49	#1 (permalink)
rahul_rocks3 No Life Poster Join Date: May 2010 Location: <:D-R-E-A-M-S:> Posts: 2,814 Member: 1312746 Status: Offline Thanks Meter: 766	ETS2225 - Successfully connected with riff but not able to flash ETS2225 - Successfully connected with riff but not able to flash I have been able to connect ETS2225 with riff but I am not able to flash it..... Actually I want to unlock it....can anyone help me out please

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
How to add a language in 51xx/61xx	tati	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	05-21-2013 19:20
How to upload a new firmware...	Brand	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	06-08-2012 18:29
Help with 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	05-25-2009 16:29

05-24-2011, 10:27	#4 (permalink)
rahul_rocks3 No Life Poster Join Date: May 2010 Location: <:D-R-E-A-M-S:> Posts: 2,814 Member: 1312746 Status: Offline Thanks Meter: 766	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [QSC6XXX L36 D08] Connecting to the dead body...OK Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK Model selected: QUALCOMM (NAND) - QSC6XXX L36 D08 Detected dead body ID: 0x220B10E1

05-24-2011, 10:28	#5 (permalink)
rahul_rocks3 No Life Poster Join Date: May 2010 Location: <:D-R-E-A-M-S:> Posts: 2,814 Member: 1312746 Status: Offline Thanks Meter: 766	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [QSC6XXX L36 D08] Restarting target (nRST Low then High)...OK Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [QSC6XXX L32 D08] Getting EmbeddedICE-RT registers...OK 00 = 0xFFFFFFFF 08 = 0xFFFFFFFF 10 = 0xFFFFFFFF 01 = 0x00080008 09 = 0xFFFFFFFF 11 = 0x00080008 02 = 0x00080008 0A = 0xFFFFFFFF 12 = 0x7FFFDE7D 03 = 0xFFFFFFFF 0B = 0xFFFFFFFF 13 = 0xFFFFFFFF 04 = 0x00000008 0C = 0x00080008 14 = 0x00080008 05 = 0xFFFFFFFF 0D = 0x00080008 15 = 0x9B4FB49A 06 = 0xFFFFFFFF 0E = 0x00080008 16 = 0x0FF802F9 07 = 0xFFFFFFFF 0F = 0xFFFFFFFF 17 = 0xFFFFFFFF Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [QSC6XXX L32 D08] Resetting target...OK STATUS: Target is halted. R0 = 0x00000000 R6 = 0x00002100 R12 = 0x000030E0 R1 = 0x00000C60 R7 = 0x000023A0 R13 = 0x00003350 R2 = 0x00001734 R8 = 0x00002648 R14 = 0x000035C0 R3 = 0x000019A8 R9 = 0x00002904 R15 = 0xFFFFFFEE R4 = 0x00001C1C R10 = 0x00002BC4 CPSR = 0x00000F28 R5 = 0x00001E8C R11 = 0x00002E50 Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [QSC60XX L18 D08] Connecting to the dead body...OK Detected dead body ID: 0x220B10E1 - CORRECT! Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...FAILED ERROR: Wrong response code from the RIFF Box: 0x45

05-24-2011, 10:45	#6 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, Post here pinout which You've used, please.

01-14-2013, 04:18	#10 (permalink)
jaraganahali Insane Poster Join Date: Nov 2011 Posts: 70 Member: 1682879 Status: Offline Thanks Meter: 1	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.34, JTAG Manager Version: 1.43 Selected Resurrector: [Huawei ETS2225 V1.00] Connecting to the dead body...OK Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Detected dead body ID: 0x220B10E1 .................................................. ................................ Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.34, JTAG Manager Version: 1.43 Selected Resurrector: [Huawei ETS2225 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x220B10E1 - IGNORED! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Settings Code: 0x20010000000000000000000000400000 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected a Not Initialized FLASH1 Chip, ID: 0x0000/0x0000 (16MB) Writting FLASH1 memory from 0x000000000000 to 0x0000003FFFFF ERROR: Selected FLASH Chip was not initialized by the DCC Loader. tata indicom smart pco huawei ets 2225...unlock flash file in riff dump is 4 mb but here it is showing 16 mb...how?? plz help me..

01-14-2013, 08:17	#11 (permalink)
M0YAL No Life Poster Join Date: May 2011 Location: india Posts: 1,679 Member: 1583254 Status: Offline Sonork: 100.1602320 Thanks Meter: 4,792	Chip, ID: 0x0000/0x0000 Flash Damage

01-18-2013, 14:12	#13 (permalink)
jaraganahali Insane Poster Join Date: Nov 2011 Posts: 70 Member: 1682879 Status: Offline Thanks Meter: 1	somebody help me to find out the flash chip on huawei ets2225 so that i can change the damage chip . if possible kindly help me with picture..