GT-P1000M problem - GSM-Forum

hafftrak · 12-07-2010, 23:45

I tried to repair Samsung Galaxy Tab. First time I try it RIFF Box say resurrection complete, when we try to enter boot, nothing. So next we solder cables again but this time checking off Gremlin Zone as per RIFF's instructions. Still nothing, Tab is just blank no response.

We bricked the phone ourselves trying a mod to activate phone. Note this is a Canadian model, GT-P1000M and not the Euro version P1000 but it shouldn't make a difference since we bricked a I9000M and used I9000 setting to resurrect in the past.

Is there any way to fix this Legija, I think you will likely ask me for a complete dump of working TAB right? Unfortunately I don't have one right now.

**legija** · 12-08-2010, 00:05

Hi,
I'll send You message to sonork tomorow.

Datamaxxx · 12-25-2010, 10:53

Hi,
I have the same problem .. Please I need good backup, or how you solved it? thanks

mobisvit · 12-25-2010, 21:25

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.16, JTAG Manager Version: 1.21
Selected Resurrector: [Samsung Galaxy Tab]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.78V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete!

NO FLASH MODE (Power+Volume down+home) AFTER Resurrection
help
and after gremlin zone not help ...

mobisvit · 12-26-2010, 14:58

creators riffbox please help .
Samsung Tab still DEAD ...

**legija** · 12-26-2010, 16:44

Sunday - Wikipedia, the free encyclopedia

mobisvit · 12-27-2010, 19:34

how about some help please

Datamaxxx · 12-27-2010, 19:44

sir pls help meee :-)

Thx

mobisvit · 12-28-2010, 21:51

My Phone NOT P1000M !!! (inside phone on lable GT-P1000 !)

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.16, JTAG Manager Version: 1.21
Selected Resurrector: [Samsung Galaxy Tab]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.78V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete!

after that phone dead - no flash mode !!!

and why You merge topics !?
http://forum.gsmhosting.com/vbb/f634...oblem-1158658/

???

**legija** · 12-29-2010, 17:16

Hi,
Topic is merged because it's same problem.

It seems that there is some bug with SBL which is used right now in TAB DLL.
We're testing it again on our sample and update will be released once everything is retested and fixed.

I am sorry for any troubles You had.

**legija** · 12-30-2010, 15:46

@mobisvit

Please check Your ICQ, I've sent You a message.

mobisvit · 12-30-2010, 21:07

sorry i am lost my ICQ
please PM or e-mail me
senks

**legija** · 12-30-2010, 21:24

Quote:

Originally Posted by mobisvit

sorry i am lost my ICQ
please PM or e-mail me
senks

You also clicked on "pu$$y.zip" ?

If You lost Your ICQ, please install Sonork and register account.
Then PM me Your ID, i will explain You how to repair Your phone.

wsxl · 01-01-2011, 12:55

tell all of ourers, let's all know hot to do ,my t959 also like this

cracker_jack · 01-02-2011, 19:40

Hi Legija, why you always PM me that and I will PM you this? Please make all these fixes public so we can all benefit. No one can learn to fix if its in a PM. Please sir.

12-07-2010, 23:45	#1 (permalink)
hafftrak No Life Poster Join Date: May 2002 Location: Canada Age: 97 Posts: 553 Member: 12270 Status: Offline Thanks Meter: 107	GT-P1000M problem I tried to repair Samsung Galaxy Tab. First time I try it RIFF Box say resurrection complete, when we try to enter boot, nothing. So next we solder cables again but this time checking off Gremlin Zone as per RIFF's instructions. Still nothing, Tab is just blank no response. We bricked the phone ourselves trying a mod to activate phone. Note this is a Canadian model, GT-P1000M and not the Euro version P1000 but it shouldn't make a difference since we bricked a I9000M and used I9000 setting to resurrect in the past. Is there any way to fix this Legija, I think you will likely ask me for a complete dump of working TAB right? Unfortunately I don't have one right now.

12-25-2010, 21:25	#4 (permalink)
mobisvit Insane Poster Join Date: Feb 2005 Location: Ukraine Kyiv Posts: 88 Member: 117432 Status: Offline Thanks Meter: 6	Samsung GT-P1000 Galaxy Tab not alive Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.16, JTAG Manager Version: 1.21 Selected Resurrector: [Samsung Galaxy Tab] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.78V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete! NO FLASH MODE (Power+Volume down+home) AFTER Resurrection help and after gremlin zone not help ...

12-28-2010, 21:51	#9 (permalink)
mobisvit Insane Poster Join Date: Feb 2005 Location: Ukraine Kyiv Posts: 88 Member: 117432 Status: Offline Thanks Meter: 6	GT-P1000 resurrection not work ! please HELP ... My Phone NOT P1000M !!! (inside phone on lable GT-P1000 !) Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.16, JTAG Manager Version: 1.21 Selected Resurrector: [Samsung Galaxy Tab] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.78V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete! after that phone dead - no flash mode !!! and why You merge topics !? http://forum.gsmhosting.com/vbb/f634...oblem-1158658/ ???

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	10-16-2013 08:16
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-21-1999 19:43
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

12-08-2010, 00:05	#2 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, I'll send You message to sonork tomorow.

12-25-2010, 10:53	#3 (permalink)
Datamaxxx Junior Member Join Date: May 2004 Age: 41 Posts: 38 Member: 66620 Status: Offline Thanks Meter: 0	Hi, I have the same problem .. Please I need good backup, or how you solved it? thanks

12-26-2010, 14:58	#5 (permalink)
mobisvit Insane Poster Join Date: Feb 2005 Location: Ukraine Kyiv Posts: 88 Member: 117432 Status: Offline Thanks Meter: 6	creators riffbox please help . Samsung Tab still DEAD ...

12-26-2010, 16:44	#6 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Sunday - Wikipedia, the free encyclopedia

12-27-2010, 19:34	#7 (permalink)
mobisvit Insane Poster Join Date: Feb 2005 Location: Ukraine Kyiv Posts: 88 Member: 117432 Status: Offline Thanks Meter: 6	how about some help please

12-27-2010, 19:44	#8 (permalink)
Datamaxxx Junior Member Join Date: May 2004 Age: 41 Posts: 38 Member: 66620 Status: Offline Thanks Meter: 0	sir pls help meee :-) Thx

12-29-2010, 17:16	#10 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, Topic is merged because it's same problem. It seems that there is some bug with SBL which is used right now in TAB DLL. We're testing it again on our sample and update will be released once everything is retested and fixed. I am sorry for any troubles You had.

12-30-2010, 15:46	#11 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	@mobisvit Please check Your ICQ, I've sent You a message.

12-30-2010, 21:07	#12 (permalink)
mobisvit Insane Poster Join Date: Feb 2005 Location: Ukraine Kyiv Posts: 88 Member: 117432 Status: Offline Thanks Meter: 6	sorry i am lost my ICQ please PM or e-mail me senks

01-01-2011, 12:55	#14 (permalink)
wsxl Junior Member Join Date: Oct 2009 Posts: 24 Member: 1133950 Status: Offline Thanks Meter: 1	tell all of ourers, let's all know hot to do ,my t959 also like this

01-02-2011, 19:40	#15 (permalink)
cracker_jack No Life Poster Join Date: Jul 2004 Posts: 519 Member: 72951 Status: Offline Thanks Meter: 63	Hi Legija, why you always PM me that and I will PM you this? Please make all these fixes public so we can all benefit. No one can learn to fix if its in a PM. Please sir.