gt-s5260 error - GSM-Forum

dozda2005 · 04-07-2011, 23:19

Who has the Samsung S5260 in working condition, consider the full please. contact me ICQ: 486-026-203
P.S. Sorry for my english =)

dozda2005 · 04-09-2011, 22:43

People, help me please

dozda2005 · 04-13-2011, 17:22

up thread. help please

ZetMen · 04-19-2011, 19:06

i have use the pinout and i dont see vcc but my phone is not connecting with battery and usb cable i try to connect power supplie and it doesnt show that takes any power when i press power it comes 0,05a but riff says cannot find rtck :
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.22, JTAG Manager Version: 1.30
Selected Resurrector: [Samsung S5260]

Connecting to the dead body...ERROR
ERROR: The RTCK Signal does not respond.
i connect all from one to 8 i try also the 9 as vcc and not working

bigstarfirst · 05-08-2011, 16:44

same problem I have can you help me riffbox team

rahul_rocks3 · 05-08-2011, 20:32

pls insert the charger to the charging connector and then try connecting ur handset

bigstarfirst · 05-09-2011, 11:29

thanks for answer but same problem
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.23, JTAG Manager Version: 1.32
Selected Resurrector: [Samsung S5260]

Connecting to the dead body...ERROR
ERROR: The RTCK Signal does not respond.

I tried with charger

rahul_rocks3 · 05-09-2011, 19:22

contact me on yahoo...i will try to solve

bigstarfirst · 05-10-2011, 17:15

hi I dont have yahoo can we contact from msn?

dozda2005 · 05-11-2011, 10:33

up again thread. HELP!!!!

linjie · 05-14-2011, 16:45

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.23, JTAG Manager Version: 1.32
Selected Resurrector: [Samsung S5260]
Connecting to the dead body...ERROR
ERROR: The RTCK Signal does not respond.

linjie · 05-14-2011, 18:22

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.23, JTAG Manager Version: 1.32
Selected Resurrector: [Samsung S5260]
Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - IGNORED!
Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0040 (256MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB
Flashing the dead body...
ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...

error!!!!!!!

**legija** · 05-19-2011, 17:53

Hi,

There is error with S5260 pinout in RIFF DLL.
You need to use pinout as for 5230 (9 pin).

There appears to be some more bugs, related to NAND access, which is going to be fixed in following days.

senis · 06-16-2011, 10:21

same eror
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.23, JTAG Manager Version: 1.32
Selected Resurrector: [Samsung S5260]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0040 (256MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Flashing the dead body...
ERROR: DCC Loader has reported Error Code = 0x2E (0x000000). Trying to recover...OK
ERROR: DCC Loader has reported Error Code = 0x2E (0x000000). Trying to recover...OK
ERROR: DCC Loader has reported Error Code = 0x2E (0x000000). Trying to recover...OK
ERROR: Stopped due to multiple communication errors. Terminating at 0x00000000
br senis

Vanga · 08-23-2011, 23:23

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [Samsung S5260]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 12 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Flashing the dead body...OK
Resurrection complete!

04-07-2011, 23:19	#1 (permalink)
dozda2005 Junior Member Join Date: Dec 2005 Posts: 20 Member: 208883 Status: Offline Thanks Meter: 3	Samsung S5260 Who has the Samsung S5260 in working condition, consider the full please. contact me ICQ: 486-026-203 P.S. Sorry for my english =)

04-19-2011, 19:06	#4 (permalink)
ZetMen Freak Poster Join Date: Sep 2002 Location: Cyprus Age: 42 Posts: 429 Member: 15149 Status: Offline Thanks Meter: 61	gt-s5260 cannot connect i have use the pinout and i dont see vcc but my phone is not connecting with battery and usb cable i try to connect power supplie and it doesnt show that takes any power when i press power it comes 0,05a but riff says cannot find rtck : Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.22, JTAG Manager Version: 1.30 Selected Resurrector: [Samsung S5260] Connecting to the dead body...ERROR ERROR: The RTCK Signal does not respond. i connect all from one to 8 i try also the 9 as vcc and not working

05-14-2011, 16:45	#11 (permalink)
linjie Freak Poster Join Date: Jul 2007 Posts: 141 Member: 557753 Status: Offline Thanks Meter: 6	gt-s5260 error Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.23, JTAG Manager Version: 1.32 Selected Resurrector: [Samsung S5260] Connecting to the dead body...ERROR ERROR: The RTCK Signal does not respond.

08-23-2011, 23:23	#15 (permalink)
Vanga Freak Poster Join Date: Dec 2001 Location: Lietuva Age: 55 Posts: 106 Member: 8172 Status: Offline Thanks Meter: 22	S5260 ist okei Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [Samsung S5260] Connecting to the dead body...OK Detected dead body ID: 0x07926F0F - CORRECT! Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 12 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...OK Resurrection complete!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-09-2011, 22:43	#2 (permalink)
dozda2005 Junior Member Join Date: Dec 2005 Posts: 20 Member: 208883 Status: Offline Thanks Meter: 3	People, help me please

04-13-2011, 17:22	#3 (permalink)
dozda2005 Junior Member Join Date: Dec 2005 Posts: 20 Member: 208883 Status: Offline Thanks Meter: 3	up thread. help please

05-08-2011, 16:44	#5 (permalink)
bigstarfirst Freak Poster Join Date: Aug 2003 Age: 39 Posts: 163 Member: 37577 Status: Offline Thanks Meter: 7	same problem I have can you help me riffbox team

05-08-2011, 20:32	#6 (permalink)
rahul_rocks3 No Life Poster Join Date: May 2010 Location: <:D-R-E-A-M-S:> Posts: 2,814 Member: 1312746 Status: Offline Thanks Meter: 766	pls insert the charger to the charging connector and then try connecting ur handset

05-09-2011, 11:29	#7 (permalink)
bigstarfirst Freak Poster Join Date: Aug 2003 Age: 39 Posts: 163 Member: 37577 Status: Offline Thanks Meter: 7	thanks for answer but same problem Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.23, JTAG Manager Version: 1.32 Selected Resurrector: [Samsung S5260] Connecting to the dead body...ERROR ERROR: The RTCK Signal does not respond. I tried with charger

05-09-2011, 19:22	#8 (permalink)
rahul_rocks3 No Life Poster Join Date: May 2010 Location: <:D-R-E-A-M-S:> Posts: 2,814 Member: 1312746 Status: Offline Thanks Meter: 766	contact me on yahoo...i will try to solve

05-10-2011, 17:15	#9 (permalink)
bigstarfirst Freak Poster Join Date: Aug 2003 Age: 39 Posts: 163 Member: 37577 Status: Offline Thanks Meter: 7	hi I dont have yahoo can we contact from msn?

05-11-2011, 10:33	#10 (permalink)
dozda2005 Junior Member Join Date: Dec 2005 Posts: 20 Member: 208883 Status: Offline Thanks Meter: 3	up again thread. HELP!!!!

05-14-2011, 18:22	#12 (permalink)
linjie Freak Poster Join Date: Jul 2007 Posts: 141 Member: 557753 Status: Offline Thanks Meter: 6	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.23, JTAG Manager Version: 1.32 Selected Resurrector: [Samsung S5260] Connecting to the dead body...OK Detected dead body ID: 0x07926F0F - IGNORED! Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0040 (256MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body... ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover... error!!!!!!!

05-19-2011, 17:53	#13 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, There is error with S5260 pinout in RIFF DLL. You need to use pinout as for 5230 (9 pin). There appears to be some more bugs, related to NAND access, which is going to be fixed in following days.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
where to find a working program all they have some errors ??	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	12-12-2012 13:26
My 5110 v5.11 have a strange error.., it resets it self every 60second	luuk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	24	08-11-2006 15:29
Avoid 3 times error code in Nokia 6185	X-plot	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	05-08-2000 20:24
The multiple errors of Winlock ... ???	Genata	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	09-20-1999 19:12
error (1002) simlock3.dll winopen	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	08-28-1999 15:57

06-16-2011, 10:21	#14 (permalink)
senis Freak Poster Join Date: Jul 2003 Location: Lithuania Age: 50 Posts: 200 Member: 35964 Status: Offline Thanks Meter: 3	same eror Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.23, JTAG Manager Version: 1.32 Selected Resurrector: [Samsung S5260] Connecting to the dead body...OK Detected dead body ID: 0x07926F0F - CORRECT! Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0040 (256MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body... ERROR: DCC Loader has reported Error Code = 0x2E (0x000000). Trying to recover...OK ERROR: DCC Loader has reported Error Code = 0x2E (0x000000). Trying to recover...OK ERROR: DCC Loader has reported Error Code = 0x2E (0x000000). Trying to recover...OK ERROR: Stopped due to multiple communication errors. Terminating at 0x00000000 br senis