htc desire after riff dead - GSM-Forum

2049567 · 06-12-2011, 10:36

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [HTC Desire]
Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB
Flashing the dead body...FAILED
ERROR: Resurrection is not Completed due to Error: 0x3901

mobile. · 06-12-2011, 10:39

set your RTCK sample rate to a very low number ...

Sent from my xxx using Tapatalk

2049567 · 06-12-2011, 10:54

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [HTC Desire]
Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 800 kHz]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB
Flashing the dead body...FAILED
ERROR: Resurrection is not Completed due to Error: 0x3901

mobile. · 06-12-2011, 11:12

6 or 8

Sent from my xxx using Tapatalk

2049567 · 06-12-2011, 11:16

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [HTC Desire]
Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 6 MHz]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB
Flashing the dead body...FAILED
ERROR: Resurrection is not Completed due to Error: 0x3901

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [HTC Desire]
Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 8 MHz]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB
Flashing the dead body...FAILED
ERROR: Resurrection is not Completed due to Error: 0x3901

mobile. · 06-12-2011, 11:35

I would say it maybe a hardware problem but what was the state of the phone before hand ? Or are you just changing the CID or unlocking ?

Sent from my xxx using Tapatalk

mobile. · 06-12-2011, 11:37

Some times with this phone it error outs at about 40 percent but the phone will still get in Hboot after . How far do you get ?

Sent from my xxx using Tapatalk

2049567 · 06-12-2011, 12:41

it finshes 100% and no boot
i have 5 phones same thing
all after last update prior to update all was 100%

**legija** · 06-13-2011, 09:02

Quote:

Originally Posted by 2049567

it finshes 100% and no boot
i have 5 phones same thing
all after last update prior to update all was 100%

Hi,

You need to rewrite HTC Partition too.

2049567 · 06-14-2011, 07:41

Quote:

Originally Posted by legija

Hi,

You need to rewrite HTC Partition too.

Where are you I am doing this???

**legija** · 06-14-2011, 17:08

Rewrite phone IMEI, this will also rewrite HTC partition. You can also write supercid (11111111).

Repair4u · 06-23-2011, 19:51

Quote:

Originally Posted by legija

Rewrite phone IMEI, this will also rewrite HTC partition. You can also write supercid (11111111).

i did same thng resurrection done? but fone is not going to botloader mode ,phone was ok HTC MOZART ,came to me for rebuild imei.

06-12-2011, 10:36	#1 (permalink)
2049567 Junior Member Join Date: Mar 2008 Posts: 19 Member: 729092 Status: Offline Sonork: 99879 Thanks Meter: 0	htc desire after riff dead Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...FAILED ERROR: Resurrection is not Completed due to Error: 0x3901

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
5110 v 6.0 after unlocking problem with net	cole	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	01-10-2001 16:11
5110/6110 after unlocking see only network to which it was locked and ...	2M	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	07-25-2000 00:51
5110 5.24 locked all 4 locks after unlocking...	MCG	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	03-07-2000 22:24
6150 V5.20 WANTED --- DEAD OR ALIVE --- IT'S BETTER ALIVE ! ;)))	tcamilo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	12-19-1999 22:30
"Menu 11"? after Net monitor	Pyron	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	08-09-1999 10:07

06-12-2011, 10:39	#2 (permalink)
mobile. Freak Poster Join Date: Nov 2010 Location: UK Posts: 449 Member: 1454100 Status: Offline Thanks Meter: 28	set your RTCK sample rate to a very low number ... Sent from my xxx using Tapatalk

06-12-2011, 10:54	#3 (permalink)
2049567 Junior Member Join Date: Mar 2008 Posts: 19 Member: 729092 Status: Offline Sonork: 99879 Thanks Meter: 0	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 800 kHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...FAILED ERROR: Resurrection is not Completed due to Error: 0x3901

06-12-2011, 11:12	#4 (permalink)
mobile. Freak Poster Join Date: Nov 2010 Location: UK Posts: 449 Member: 1454100 Status: Offline Thanks Meter: 28	6 or 8 Sent from my xxx using Tapatalk

06-12-2011, 11:16	#5 (permalink)
2049567 Junior Member Join Date: Mar 2008 Posts: 19 Member: 729092 Status: Offline Sonork: 99879 Thanks Meter: 0	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 6 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...FAILED ERROR: Resurrection is not Completed due to Error: 0x3901 Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.24, JTAG Manager Version: 1.32 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 8 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...FAILED ERROR: Resurrection is not Completed due to Error: 0x3901

06-12-2011, 11:35	#6 (permalink)
mobile. Freak Poster Join Date: Nov 2010 Location: UK Posts: 449 Member: 1454100 Status: Offline Thanks Meter: 28	I would say it maybe a hardware problem but what was the state of the phone before hand ? Or are you just changing the CID or unlocking ? Sent from my xxx using Tapatalk

06-12-2011, 11:37	#7 (permalink)
mobile. Freak Poster Join Date: Nov 2010 Location: UK Posts: 449 Member: 1454100 Status: Offline Thanks Meter: 28	Some times with this phone it error outs at about 40 percent but the phone will still get in Hboot after . How far do you get ? Sent from my xxx using Tapatalk

06-12-2011, 12:41	#8 (permalink)
2049567 Junior Member Join Date: Mar 2008 Posts: 19 Member: 729092 Status: Offline Sonork: 99879 Thanks Meter: 0	it finshes 100% and no boot i have 5 phones same thing all after last update prior to update all was 100%

06-14-2011, 17:08	#11 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Rewrite phone IMEI, this will also rewrite HTC partition. You can also write supercid (11111111).