huawei 2607 blink problam sholved but white display - GSM-Forum

prabash007 · 02-19-2011, 08:49

2607 blink problam sholved but white display
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.18, JTAG Manager Version: 1.25
Selected Resurrector: [Huawei C2806M]
Connecting to the dead body...OK
Detected dead body ID: 0x220B10E1 - IGNORED!
Set I/O Voltage reads as 2.63V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x00EC/0x257E (4MB)
Flashing the dead body...OK
Resurrection complete!

**legija** · 02-19-2011, 13:40

Hi,
You need to write full backup from working phone, this should help if there is not some HW problem.

prabash007 · 02-19-2011, 15:42

any bady pls uplode 2607 dump file

gsmsikar · 02-20-2011, 07:39

use this file ..

it works ..

http://forum.gsmhosting.com/vbb/6975653-post62.html

prabash007 · 02-20-2011, 11:33

Quote:

Originally Posted by gsmsikar

use this file ..

it works ..

http://forum.gsmhosting.com/vbb/6975653-post62.html

same problam pls send tested file

gsmsikar · 02-20-2011, 15:22

Quote:

Originally Posted by prabash007

same problam pls send tested file

it is tested by me and its working ..

prabash007 · 02-21-2011, 08:35

Quote:

Originally Posted by gsmsikar

it is tested by me and its working ..

i am secend time test this file but same problam

02-19-2011, 08:49	#1 (permalink)
prabash007 Crazy Poster Join Date: Feb 2011 Posts: 59 Member: 1517185 Status: Offline Sonork: [email protected] Thanks Meter: 3	huawei 2607 blink problam sholved but white display 2607 blink problam sholved but white display Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.18, JTAG Manager Version: 1.25 Selected Resurrector: [Huawei C2806M] Connecting to the dead body...OK Detected dead body ID: 0x220B10E1 - IGNORED! Set I/O Voltage reads as 2.63V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x257E (4MB) Flashing the dead body...OK Resurrection complete!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
NOKIA 5110 5.29 all locks OPEN but SIM CARD NOT ACCEPTED	elektron code ECS	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	01-10-2001 17:40
FBUS works but MBUS not! PLS Help!	Upo	Nokia Hardware & Hardware Repair	5	09-12-2000 14:54
Blue LEDs in your Display SUPER!	GM	Nokia Hardware & Hardware Repair	0	06-25-2000 12:47
6110 unlocked but wont give reception	KingOfKingston	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	04-10-2000 22:15
blue Display in Nokia Cellphones	TheDon	Nokia Hardware & Hardware Repair	0	10-29-1999 18:28

02-19-2011, 13:40	#2 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, You need to write full backup from working phone, this should help if there is not some HW problem.

02-19-2011, 15:42	#3 (permalink)
prabash007 Crazy Poster Join Date: Feb 2011 Posts: 59 Member: 1517185 Status: Offline Sonork: [email protected] Thanks Meter: 3	any bady pls uplode 2607 dump file

02-20-2011, 07:39	#4 (permalink)
gsmsikar No Life Poster Join Date: May 2003 Posts: 5,667 Member: 28004 Status: Offline Sonork: 100.1601142 Thanks Meter: 770	use this file .. it works .. http://forum.gsmhosting.com/vbb/6975653-post62.html