huawei c5320 blinking - GSM-Forum

gsmsikar · 04-12-2011, 14:49

in a huawei c5320 the set is in blinking condition , i am unable to do force download so i try to connect it with JTAG

but when i try to connect it in DCC read tab it says

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.22, JTAG Manager Version: 1.30
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the dead body...ERROR
ERROR: The RTCK Signal does not respond.

when i read in JTAG tab then i get these details

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.22, JTAG Manager Version: 1.30
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.59V, TCK Frequency is 4 MHz
Model selected: QUALCOMM (NOR) - QSC60XX L20 D08

Detected dead body ID: 0x3F0F0F0F

analyze jtag chain

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.22, JTAG Manager Version: 1.30
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the target...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is 4 MHz

Following devices are found on the JTAG chain:
  Device on TAP #0: ID = 0x3F0F0F0F, IR Length = 0x04 bits
Total IR length: 0x0004 bits

please help ..

lalitgvarshney · 04-12-2011, 16:22

[QUOTE=gsmsikar;7190306]in a huawei c5320 the set is in blinking condition , i am unable to do force download so i try to connect it with JTAG

but when i try to connect it in DCC read tab it says

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.22, JTAG Manager Version: 1.30
Selected Resurrector: [QSC60XX L20 D08]
 
Connecting to the dead body...ERROR
ERROR: The RTCK Signal does not respond.

It means RTCK does not connect on Jtag Pads Kindly Check Ur Jtag connection

wbr
lalitg

gsmsikar · 04-12-2011, 18:58

if RTCK is not connected then

a ) how can JTAG TAB shows set is connected ?
b ) is RTCK not used for JTAG TAB connection ?

amit_deswal22 · 06-11-2011, 11:24

i m also getting same problem

ranagaurav · 06-11-2011, 16:26

Quote:

Originally Posted by gsmsikar

if RTCK is not connected then

a ) how can JTAG TAB shows set is connected ?
b ) is RTCK not used for JTAG TAB connection ?

yes u r right i also face this problem in any models

amit kanpur · 06-12-2011, 10:02

check ur cable.....................i am connecting this model in 5330 cable.....no errors show

amit_deswal22 · 06-21-2011, 15:23

Quote:

Originally Posted by jagritisharma

check ur cable.....................i am connecting this model in 5330 cable.....no errors show

yes bro connecting ok but have u flashed in dcc tab?

{X-MAN} · 07-05-2011, 14:49

HELP ME C5320
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.25, JTAG Manager Version: 1.33
Selected Resurrector: [QSC60XX L24 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x3F0F0F0F - IGNORED!
Set I/O Voltage reads as 2.60V, TCK Frequency is 4 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: Memory access timed out.

gb2qaz · 07-05-2011, 15:38

can u post c5320 dump i wll test

MOHIT_THAREJA · 09-02-2011, 16:08

huawei c5320 dump need plz upload if anyone have

gsmsikar · 09-03-2011, 06:57

i also didnt get the dump yet , can anyone provide me that too ?

rahul_rocks3 · 09-03-2011, 07:04

will 5330 dump for 5320

nainosoft · 06-15-2012, 10:20

Sir, plz give me solution, how to connect huawei c5320 between riff box & jtag jig?
thanks in advance

04-12-2011, 16:22	#2 (permalink)
lalitgvarshney Freak Poster Join Date: Jan 2007 Location: DELHI,INDIA Posts: 376 Member: 427627 Status: Offline Thanks Meter: 160	[QUOTE=gsmsikar;7190306]in a huawei c5320 the set is in blinking condition , i am unable to do force download so i try to connect it with JTAG but when i try to connect it in DCC read tab it says Code: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.22, JTAG Manager Version: 1.30 Selected Resurrector: [QSC60XX L20 D08] Connecting to the dead body...ERROR ERROR: *The RTCK Signal does not respond*. It means RTCK does not connect on Jtag Pads Kindly Check Ur Jtag connection wbr lalitg

06-15-2012, 10:20	#13 (permalink)
nainosoft Freak Poster Join Date: Jan 2012 Location: I /\/ D ! /_\ Posts: 259 Member: 1713692 Status: Offline Sonork: 1637132, QQ-2486154669 Thanks Meter: 187	How to connect huawei c5320 between riff box & jtag jig? Sir, plz give me solution, how to connect huawei c5320 between riff box & jtag jig? thanks in advance

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Where can i download program for blinking sms	Ari	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	15	01-29-2009 17:47
please help "in c25 v10 light automatically blinks and switches off "	sidharthaharish	x1x to x45/x50	2	12-29-2001 22:40
a1018s blink only	eureka8888	Old Ericsson Phones & Sony Phones	2	10-04-2001 09:39
Help need 3330 Ver.305 double blink CS repairer	ced1298	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	08-29-2001 18:13
A 36 Blink and off	pez8210	x1x to x45/x50	0	08-05-2001 22:23

04-12-2011, 18:58	#3 (permalink)
gsmsikar No Life Poster Join Date: May 2003 Posts: 5,667 Member: 28004 Status: Offline Sonork: 100.1601142 Thanks Meter: 770	if RTCK is not connected then a ) how can JTAG TAB shows set is connected ? b ) is RTCK not used for JTAG TAB connection ?

06-11-2011, 11:24	#4 (permalink)
amit_deswal22 Freak Poster Join Date: May 2008 Posts: 348 Member: 778346 Status: Offline Thanks Meter: 34	i m also getting same problem

06-12-2011, 10:02	#6 (permalink)
amit kanpur No Life Poster Join Date: May 2009 Location: kanpur Age: 35 Posts: 2,443 Member: 1033905 Status: Offline Sonork: amitsharma Thanks Meter: 892	check ur cable.....................i am connecting this model in 5330 cable.....no errors show

07-05-2011, 14:49	#8 (permalink)
{X-MAN} Freak Poster Join Date: Nov 2009 Location: I.N.D.I.A Posts: 180 Member: 1169043 Status: Offline Sonork: 100.1586033 Thanks Meter: 58	HELP ME C5320 Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.25, JTAG Manager Version: 1.33 Selected Resurrector: [QSC60XX L24 D08] Connecting to the dead body...OK Detected dead body ID: 0x3F0F0F0F - IGNORED! Set I/O Voltage reads as 2.60V, TCK Frequency is 4 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...FAILED ERROR: Memory access timed out.

07-05-2011, 15:38	#9 (permalink)
gb2qaz No Life Poster Join Date: Jan 2007 Posts: 582 Member: 441202 Status: Offline Thanks Meter: 120	can u post c5320 dump i wll test

09-02-2011, 16:08	#10 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	huawei c5320 dump need plz upload if anyone have

09-03-2011, 06:57	#11 (permalink)
gsmsikar No Life Poster Join Date: May 2003 Posts: 5,667 Member: 28004 Status: Offline Sonork: 100.1601142 Thanks Meter: 770	i also didnt get the dump yet , can anyone provide me that too ?

09-03-2011, 07:04	#12 (permalink)
rahul_rocks3 No Life Poster Join Date: May 2010 Location: <:D-R-E-A-M-S:> Posts: 2,814 Member: 1312746 Status: Offline Thanks Meter: 766	will 5330 dump for 5320