i900 pda - GSM-Forum

KHALEDGROOZE · 06-09-2012, 13:09

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung i900 PDA V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x2E649013 - CORRECT!
Set I/O Voltage reads as 3.30V, TCK Frequency is 10 MHz

Resurrection sequence started.
Establish communication with the phone...FAILED
ERROR(0x42): Communication is not established. Terminating.

try power on not repon

BABAK NURI · 06-10-2012, 02:25

Hi
Please check:
RIFF JTAG Box FAQ - ERROR(0x42): Communication is not established. Terminating.

KHALEDGROOZE · 06-11-2012, 17:14

now is complet

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung i900 PDA V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x2E649013 - CORRECT!
Set I/O Voltage reads as 3.30V, TCK Frequency is 10 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB)
Flashing the dead body...OK
Resurrection complete!

06-09-2012, 13:09	#1 (permalink)
KHALEDGROOZE Junior Member Join Date: Aug 2010 Posts: 16 Member: 1366785 Status: Offline Thanks: 2 Thanked 1 Time in 1 Post	i900 pda Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung i900 PDA V1.00] Connecting to the dead body...OK Detected dead body ID: 0x2E649013 - CORRECT! Set I/O Voltage reads as 3.30V, TCK Frequency is 10 MHz Resurrection sequence started. Establish communication with the phone...FAILED ERROR(0x42): Communication is not established. Terminating. try power on not repon

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
PDA Unlock	nokiak	Old Ericsson Phones & Sony Phones	4	11-06-2002 18:19
Problem with PDA in 9110	Skoku	Nokia Hardware & Hardware-Repair Area	5	08-24-2002 17:45
9110 PDA Display fault! please help!	drucrew	Nokia Hardware & Hardware-Repair Area	0	03-18-2002 21:29
What software required to sync. T39m with PDA..?	aero69	Old Ericsson Phones & Sony Phones	0	12-31-2001 03:57

06-10-2012, 02:25	#2 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 32 Posts: 5,081 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks: 517 Thanked 1,474 Times in 965 Posts	Hi Please check: RIFF JTAG Box FAQ - ERROR(0x42): Communication is not established. Terminating.

06-11-2012, 17:14	#3 (permalink)
KHALEDGROOZE Junior Member Join Date: Aug 2010 Posts: 16 Member: 1366785 Status: Offline Thanks: 2 Thanked 1 Time in 1 Post	now is complet Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung i900 PDA V1.00] Connecting to the dead body...OK Detected dead body ID: 0x2E649013 - CORRECT! Set I/O Voltage reads as 3.30V, TCK Frequency is 10 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB) Flashing the dead body...OK Resurrection complete!