i9100 boot repair help...

[behnam64]

hi friends
i have a new dead i9100.i try to repair it with riff

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung i9100 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Flashing the dead body...OK
Resurrection complete!

but it doesn't go on bootloader state.plz help and shre ur experiences.

[BABAK NURI]

Hi
I Thinnk You Need Check HW...Like Power Circuite
But,Please Tell Me About Phone History.....

[behnam64]

bazam hamvatanaye golam....

during update procedure its died,phone is likely new and fresh.may not be HW

[behnam64]

any body help me????

[borjan_vujic2]

Originally Posted by behnam64

bazam hamvatanaye golam....

during update procedure its died,phone is likely new and fresh.may not be HW

i have same problem.....

[BABAK NURI]

Hi
Please Note:

Samsung_I9100.dll (Exynos4210)
-------------------------------------
- Resurrection is full now (FBL, IBL and PBL loaders as was noted in previous version of DLL were not resurrected)
Now complete boot area is resurrected, which guarantees that phone will power on after resurrection (if no h/w damage).

http://forum.gsmhosting.com/vbb/8021074-post244.html
--------------------------------------------------------

Not bad idea if you want test this:
http://forum.gsmhosting.com/vbb/f634...ution-1508808/

[chliki2001]

HI BABAK NURI IN ALL THERE R NO REAL SOLUTION FOR I 9100 DEAD
AFTER ALL JOB IN HOSTING PHONE STEAL DEAD AND WHAT behnam64 SAID R A REALY PROBLEM

[BABAK NURI]

Hi chliki2001
What do you think about this:
i haved 2 set i9100(dead phone Suddenly)....Resurrect/erase/write dump/write boot.bin Rom2..Can't Help...
First phone haved "Error (0x25)...another dead phone not happen after press power key(check via power supply)Also Can't detected by riff

I have another i9100,dead by water damage in sea......i did remove eMMC Chip From phone and put into First Phone(With error 0x25)
------------------
Can You tell me what happened? *** Phone turn on without resurrect or any other via jtag....Just need flash phone via odin,because phone hang on logo
Anyway,after start up phone,i did check "MyFile"....Hehehe,,,i see all old photo.video,etc still here
--------------------
For Another phone i did replace "UCP300" it's Power Managment...This phone turn on without flash or jtag
So,You should know that electronics part can die

[chliki2001]

Originally Posted by behnam64

hi friends
i have a new dead i9100.i try to repair it with riff



but it doesn't go on bootloader state.plz help and shre ur experiences.

BUT FOR behnam64 CAN U TELL HIM WHAT HE DO FACE TO THAT COZ I HV THE SAME PROBLREM
BUT I DONT TRY WITH ORT
I TRY AND ....

[zeljko_c]

I got one dead, water damaged, solved! One capacitor near charge block was damaged!Removed and bot up again But, that`s not mean same for all!