i9100 new emmc - GSM-Forum

Sasha_neo · 03-20-2013, 16:22

hi. help me pls. i replaced faulty emmc by new one (not from donor). by using RIFF erase is ok, resurect ok, but no download mode. I notice when i flash any partition with plugin then check for blank it says that partition is blank. how it can be? help pls, thanks

islamic.tj · 03-20-2013, 19:33

read manual, after replace new emmc other procedur repair

Sasha_neo · 03-20-2013, 21:24

Can you give a link pls?

BABAK NURI · 03-20-2013, 22:12

Hi
For First...Plz Tell Me About New Chip....Where You Find This? I Mean,You Did use from PCB or it's a blank chip?Also if u used from another pcb,,What Model?
----

After replace,,,You Need Only Resurrect
Erase Option Not Work For "eMMC"
No Need Reparition for I9100

Sasha_neo · 03-20-2013, 22:20

I ordered chip from samsung (AUthServCent) same emmc that was on board

Sasha_neo · 03-20-2013, 22:21

It it absolutely new blank chip. Log will be tomorow

Sasha_neo · 03-21-2013, 08:28

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.48
Selected Resurrector: [Samsung I9100 V1.0.4724.60074]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Selected Resurrection Data for the eMMC Chip with Capacity = 14,68GB

Flashing the dead body...OK
Resurrection complete!

Now use plugin, Layout from device

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.48
Selected Resurrector: [Samsung I9100 V1.0.4724.60074]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz
Settings Code: 0x08010B000000000000000003AB3FFFFF

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Looking for the RIFF BOX DCCLoader USB Interface Port...FAILED
The DCCLoader USB Interface is not found. Communication continues over the DCC Interface

Reading FLASH1 address space from 0x000000000000 to 0x0000000001FF
Completed in 00:00:00.015 (Average Transfer Rate: 139810133.27 kB/s)

Reading FLASH1 address space from 0x000000004400 to 0x0000000045FF
Completed in 00:00:00.016 (Average Transfer Rate: 131071999.94 kB/s)

Reading FLASH1 address space from 0x000000000000 to 0x0000000001FF
Completed in 00:00:00.015 (Average Transfer Rate: 1266.67 kB/s)

Reading FLASH1 address space from 0x000000004400 to 0x000000004BFF
Completed in 00:00:00.016 (Average Transfer Rate: 1187.50 kB/s)

Analizing the FullImage File...OK
Current Phone/Image File has PIT Structure.
Total quantity of listed partitions: 18

Layout from file (I use full flash), tick for exm EFS patition and flash into device

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Looking for the RIFF BOX DCCLoader USB Interface Port...FAILED
The DCCLoader USB Interface is not found. Communication continues over the DCC Interface

Writting FLASH1 memory from 0x000000400000 to 0x0000017FFFFF
Completed in 00:03:10.281 (Average Transfer Rate: 107.63 kB/s)

then load from device, and check for blank

Checking which Partition is blank...COMPLETE!
Following partitions are found to be completely blank:
Partition: GANG at 0x000000000000
Partition: BOOT at 0x000000000000
Partition: P09 at 0x000000000000
Partition: EFS at 0x000000400000
Partition: SBL1 at 0x000001800000
Partition: EMPTY at 0x000001940000
Partition: SBL2 at 0x000001A00000
Partition: EMPTY at 0x000001B40000
Partition: PARAM at 0x000001C00000
Partition: KERNEL at 0x000002400000
Partition: RECOVERY at 0x000002C00000
Partition: CACHE at 0x000003400000
Partition: MODEM at 0x000009800000
Partition: FACTORYFS at 0x00000A800000
Partition: DATAFS at 0x00002A800000
Partition: UMS at 0x0000AA800000
Partition: HIDDEN at 0x00038B000000
Thus in total, there are 17 blank partitions.

Why flashed partition (EFS) is still blank? Help pls
PC find device on usb like SEC S5PC210 B/D
How to flash bootloader? Thanks

Sasha_neo · 03-22-2013, 07:13

pls somebody explain me how to flsh bootloader

**legija** · 03-22-2013, 11:58

RIFF JTAG Box FAQ - How to use QUALCOMM/Exynos eMMC EFI/PIT/MBR/EBR Partitioning plugin

This is very useful article You should read.

Partitions are blank because You havent read any. You just read partitions table.
You should also upload phone EFS after replacing eMMC, to get phone working.

Sasha_neo · 03-22-2013, 13:27

Legija, I read this article before, about erased and new chips , tried load image from fullflash file, then repartition and second way - saved from fullflash "Save only eMMC Re-partition info" , then load from this file and repartition

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Writting FLASH1 memory from 0x000000000000 to 0x0000000001FF
Completed in 00:00:00.047 (Average Transfer Rate: 10.64 kB/s)

Partition Sectors are Flashed OK.

then Resurrection

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.48
Selected Resurrector: [Samsung I9100 V1.0.4724.60074]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Selected Resurrection Data for the eMMC Chip with Capacity = 14,68GB

Flashing the dead body...OK
Resurrection complete!

still there is no download mode (
my previous i9100 with new blank chip was with trouble too, it was solved by initiation download mode with jtag manager 1.47. But now in 1.48 there is no such option

Sasha_neo · 03-22-2013, 15:42

yes, partitions is not blank, but still there is no download mode...any ideas? help pls

zenglq2004 · 03-22-2013, 16:36

blank chip Need to write EMMC bottom

zenglq2004 · 03-22-2013, 16:37

JTAG cannot write blank chip

Sasha_neo · 03-22-2013, 20:16

Legija and BABAK NURI I hope for your help

BABAK NURI · 03-23-2013, 12:23

Hi
This is very easy ....
if your chip is fine,,,,phone must power on after "resurrecct"
---
Anyway..i'm in sonork,,for now ...
Plz connect phone to riff and contact me...

Thanks

03-20-2013, 16:22	#1 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	i9100 new emmc hi. help me pls. i replaced faulty emmc by new one (not from donor). by using RIFF erase is ok, resurect ok, but no download mode. I notice when i flash any partition with plugin then check for blank it says that partition is blank. how it can be? help pls, thanks

03-20-2013, 19:33	#2 (permalink)
islamic.tj No Life Poster Join Date: Mar 2011 Location: Tadjikistan, Dushanbe Age: 35 Posts: 552 Member: 1533366 Status: Offline Thanks Meter: 131	read manual, after replace new emmc other procedur repair

03-20-2013, 21:24	#3 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	Can you give a link pls?

03-20-2013, 22:12	#4 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Hi For First...Plz Tell Me About New Chip....Where You Find This? I Mean,You Did use from PCB or it's a blank chip?Also if u used from another pcb,,What Model? ---- After replace,,,You Need Only Resurrect Erase Option Not Work For "eMMC" No Need Reparition for I9100

03-20-2013, 22:20	#5 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	I ordered chip from samsung (AUthServCent) same emmc that was on board

03-20-2013, 22:21	#6 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	It it absolutely new blank chip. Log will be tomorow

03-21-2013, 08:28	#7 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.34, JTAG Manager Version: 1.48 Selected Resurrector: [Samsung I9100 V1.0.4724.60074] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Selected Resurrection Data for the eMMC Chip with Capacity = 14,68GB Flashing the dead body...OK Resurrection complete! Now use plugin, Layout from device Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.34, JTAG Manager Version: 1.48 Selected Resurrector: [Samsung I9100 V1.0.4724.60074] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz Settings Code: 0x08010B000000000000000003AB3FFFFF Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Looking for the RIFF BOX DCCLoader USB Interface Port...FAILED The DCCLoader USB Interface is not found. Communication continues over the DCC Interface Reading FLASH1 address space from 0x000000000000 to 0x0000000001FF Completed in 00:00:00.015 (Average Transfer Rate: 139810133.27 kB/s) Reading FLASH1 address space from 0x000000004400 to 0x0000000045FF Completed in 00:00:00.016 (Average Transfer Rate: 131071999.94 kB/s) Reading FLASH1 address space from 0x000000000000 to 0x0000000001FF Completed in 00:00:00.015 (Average Transfer Rate: 1266.67 kB/s) Reading FLASH1 address space from 0x000000004400 to 0x000000004BFF Completed in 00:00:00.016 (Average Transfer Rate: 1187.50 kB/s) Analizing the FullImage File...OK Current Phone/Image File has PIT Structure. Total quantity of listed partitions: 18 Layout from file (I use full flash), tick for exm EFS patition and flash into device Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Looking for the RIFF BOX DCCLoader USB Interface Port...FAILED The DCCLoader USB Interface is not found. Communication continues over the DCC Interface Writting FLASH1 memory from 0x000000400000 to 0x0000017FFFFF Completed in 00:03:10.281 (Average Transfer Rate: 107.63 kB/s) then load from device, and check for blank Checking which Partition is blank...COMPLETE! Following partitions are found to be completely blank: Partition: GANG at 0x000000000000 Partition: BOOT at 0x000000000000 Partition: P09 at 0x000000000000 Partition: EFS at 0x000000400000 Partition: SBL1 at 0x000001800000 Partition: EMPTY at 0x000001940000 Partition: SBL2 at 0x000001A00000 Partition: EMPTY at 0x000001B40000 Partition: PARAM at 0x000001C00000 Partition: KERNEL at 0x000002400000 Partition: RECOVERY at 0x000002C00000 Partition: CACHE at 0x000003400000 Partition: MODEM at 0x000009800000 Partition: FACTORYFS at 0x00000A800000 Partition: DATAFS at 0x00002A800000 Partition: UMS at 0x0000AA800000 Partition: HIDDEN at 0x00038B000000 Thus in total, there are 17 blank partitions. Why flashed partition (EFS) is still blank? Help pls *PC find device on usb like SEC S5PC210 B/D* *How to flash bootloader? Thanks*

03-22-2013, 07:13	#8 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	pls somebody explain me how to flsh bootloader

03-22-2013, 11:58	#9 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	RIFF JTAG Box FAQ - How to use QUALCOMM/Exynos eMMC EFI/PIT/MBR/EBR Partitioning plugin This is very useful article You should read. Partitions are blank because You havent read any. You just read partitions table. You should also upload phone EFS after replacing eMMC, to get phone working.

03-22-2013, 13:27	#10 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	Legija, I read this article before, about erased and new chips , tried load image from fullflash file, then repartition and second way - saved from fullflash "Save only eMMC Re-partition info" , then load from this file and repartition Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Writting FLASH1 memory from 0x000000000000 to 0x0000000001FF Completed in 00:00:00.047 (Average Transfer Rate: 10.64 kB/s) Partition Sectors are Flashed OK. then Resurrection Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.34, JTAG Manager Version: 1.48 Selected Resurrector: [Samsung I9100 V1.0.4724.60074] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Selected Resurrection Data for the eMMC Chip with Capacity = 14,68GB Flashing the dead body...OK Resurrection complete! still there is no download mode ( my previous i9100 with new blank chip was with trouble too, it was solved by initiation download mode with jtag manager 1.47. But now in 1.48 there is no such option

03-22-2013, 15:42	#11 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	yes, partitions is not blank, but still there is no download mode...any ideas? help pls

03-22-2013, 16:36	#12 (permalink)
zenglq2004 Junior Member Join Date: Mar 2005 Age: 45 Posts: 11 Member: 132340 Status: Offline Thanks Meter: 0	blank chip Need to write EMMC bottom

03-22-2013, 16:37	#13 (permalink)
zenglq2004 Junior Member Join Date: Mar 2005 Age: 45 Posts: 11 Member: 132340 Status: Offline Thanks Meter: 0	JTAG cannot write blank chip

03-22-2013, 20:16	#14 (permalink)
Sasha_neo Major Poster Join Date: Mar 2007 Location: Ukraine, Kharkov Posts: 48 Member: 478835 Status: Offline Thanks Meter: 9	Legija and BABAK NURI I hope for your help

03-23-2013, 12:23	#15 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Hi This is very easy .... if your chip is fine,,,,phone must power on after "resurrecct" --- Anyway..i'm in sonork,,for now ... Plz connect phone to riff and contact me... Thanks