if anyone wants to get help with new models - GSM-Forum

gsmsikar · 12-05-2010, 20:54

if anyone wants to get help with new models with RIFF then, please post these details :-

1. details if the CPU and Flash
2. JTAG pinout details
3. Good quality board image
4. if connected then error log .
5. if connected then original dump

all this can make the process fast and easy for the supporters ..

littmanr · 12-05-2010, 21:53

What about ZTE F188? Box not detect any, on Jtag Tab only OK with Register, wait I´ll post log...Thanks.

littmanr · 12-05-2010, 22:03

ZTE F188 reading Register:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.15, JTAG Manager Version: 1.19
Selected Custom Target: [ARM926, 2.60V, TAP0]

Getting EmbeddedICE-RT registers...OK
00 = 0x00000FFF 08 = 0xFC000000 10 = 0x007FFFFF
01 = 0x00000000 09 = 0x3FFFFFFE 11 = 0x00000000
02 = 0xFFFFF000 0A = 0x0000003F 12 = 0xFFF00000
03 = 0x00000FFF 0B = 0x00000000 13 = 0x00FFFFFF
04 = 0x00000000 0C = 0xFFFFF800 14 = 0x00000000
05 = 0xFFFE0000 0D = 0x0000FFFF 15 = 0xFF000000
06 = 0x003FFFFF 0E = 0x00000000 16 = 0x007FFFFF
07 = 0x00000000 0F = 0xFFE00000 17 = 0x00000000

ZTE F188 Connect ID:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.15, JTAG Manager Version: 1.19
Selected Custom Target: [ARM926, 2.60V, TAP0]

Connecting to the ARM926 target...ERROR
Set I/O Voltage reads as 2.60V, TCK Frequency is 5 kHz

None is detected.

ZTE F188 Analyze Jtag Chain

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.15, JTAG Manager Version: 1.19
Selected Custom Target: [ARM926, 2.60V, TAP0]

Connecting to the target...ERROR
None was found.

Same Error Without RTCK Signal and Changing Different Frecuency Oscillator
Its possible repair?

littmanr · 12-05-2010, 22:09

365520DSC00396.jpg - HostingPics.net - Hébergement d'images gratuit

JTAG PINOUT

http://www.hostingpics.net/viewer.ph...98DSC00399.jpg

gsmsikar · 12-06-2010, 12:18

i think this cpu msm6245 is not supported by riff yet..

littmanr · 12-10-2010, 00:24

How to build loader & script for that cpu?

12-05-2010, 20:54	#1 (permalink)
gsmsikar No Life Poster Join Date: May 2003 Posts: 5,667 Member: 28004 Status: Offline Sonork: 100.1601142 Thanks Meter: 770	if anyone wants to get help with new models if anyone wants to get help with new models with RIFF then, please post these details :- 1. details if the CPU and Flash 2. JTAG pinout details 3. Good quality board image 4. if connected then error log . 5. if connected then original dump all this can make the process fast and easy for the supporters ..

12-10-2010, 00:24	#6 (permalink)
littmanr No Life Poster Join Date: Oct 2005 Posts: 668 Member: 190377 Status: Offline Thanks Meter: 61	How to build loader & script for that cpu? Last edited by littmanr; 12-10-2010 at 00:33.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
New Nokia Software!!!!!!!	Jefferson	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	52	12-30-2016 08:17
How to add a language in 51xx/61xx	tati	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	05-21-2013 19:20
Help with 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	05-25-2009 16:29
Tdb4 emulator wanted	Fk2	Wanted Products	0	06-01-1999 09:45

12-05-2010, 21:53	#2 (permalink)
littmanr No Life Poster Join Date: Oct 2005 Posts: 668 Member: 190377 Status: Offline Thanks Meter: 61	What about ZTE F188? Box not detect any, on Jtag Tab only OK with Register, wait I´ll post log...Thanks.

12-05-2010, 22:03	#3 (permalink)
littmanr No Life Poster Join Date: Oct 2005 Posts: 668 Member: 190377 Status: Offline Thanks Meter: 61	ZTE F188 reading Register: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.15, JTAG Manager Version: 1.19 Selected Custom Target: [ARM926, 2.60V, TAP0] Getting EmbeddedICE-RT registers...OK 00 = 0x00000FFF 08 = 0xFC000000 10 = 0x007FFFFF 01 = 0x00000000 09 = 0x3FFFFFFE 11 = 0x00000000 02 = 0xFFFFF000 0A = 0x0000003F 12 = 0xFFF00000 03 = 0x00000FFF 0B = 0x00000000 13 = 0x00FFFFFF 04 = 0x00000000 0C = 0xFFFFF800 14 = 0x00000000 05 = 0xFFFE0000 0D = 0x0000FFFF 15 = 0xFF000000 06 = 0x003FFFFF 0E = 0x00000000 16 = 0x007FFFFF 07 = 0x00000000 0F = 0xFFE00000 17 = 0x00000000 ZTE F188 Connect ID: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.15, JTAG Manager Version: 1.19 Selected Custom Target: [ARM926, 2.60V, TAP0] Connecting to the ARM926 target...ERROR Set I/O Voltage reads as 2.60V, TCK Frequency is 5 kHz None is detected. ZTE F188 Analyze Jtag Chain Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.15, JTAG Manager Version: 1.19 Selected Custom Target: [ARM926, 2.60V, TAP0] Connecting to the target...ERROR None was found. Same Error Without RTCK Signal and Changing Different Frecuency Oscillator Its possible repair?

12-06-2010, 12:18	#5 (permalink)
gsmsikar No Life Poster Join Date: May 2003 Posts: 5,667 Member: 28004 Status: Offline Sonork: 100.1601142 Thanks Meter: 770	i think this cpu msm6245 is not supported by riff yet..