n7000 cant repair - GSM-Forum

santoshniroula · 10-31-2012, 12:21

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung N7000 AP V1.0.4458.16492]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Flashing the dead body...
WARNING: Programming Error (0x25) at 0x000000000000 is handled as Cut Excess.
ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF <> 0x010000)

pablov300 · 10-31-2012, 12:30

///////////////////////////////////

**legija** · 10-31-2012, 13:20

RIFF JTAG Box FAQ - ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF 0x010000)

10-31-2012, 12:21	#1 (permalink)
santoshniroula Freak Poster Join Date: Mar 2009 Posts: 119 Member: 998040 Status: Offline Sonork: 100.151982 Thanks Meter: 33	n7000 cant repair Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.34, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung N7000 AP V1.0.4458.16492] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Flashing the dead body... WARNING: Programming Error (0x25) at 0x000000000000 is handled as Cut Excess. ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF <> 0x010000)

10-31-2012, 12:30	#2 (permalink)
pablov300 Freak Poster Join Date: Jun 2006 Location: argentina Age: 36 Posts: 132 Member: 292644 Status: Offline Thanks Meter: 19	/////////////////////////////////// Last edited by legija; 10-31-2012 at 13:21. Reason: Spam

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-31-2012, 13:20	#3 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	RIFF JTAG Box FAQ - ERROR: DCC Loader has reported Error Code = 0x3E (0x007FFF 0x010000)