NEW JTAG JIGS for DESIRE, WILDFIRE, LEGEND....

[Multi-COM]

send me PCB and will be done

[anurag_arora]

sir , who is your reseller in india

[smarttimes]

Any chance of making a postal delivery? 50bucks is way too much for a jig. I only need 3 and i am kinda stuck because of the shipping cost

[huzein]

Originally Posted by smarttimes

Any chance of making a postal delivery? 50bucks is way too much for a jig. I only need 3 and i am kinda stuck because of the shipping cost

choose shippment for about 6-7 euro.

[Multi-COM]

JTAG Samsung i5800 (Galaxy 3)



NOKOUT:
Adapter need to connect to molex connector on phone board - in 90% of cases PCB don't have this connector installed so you need to solder as on shown picture special 10 pin molex into it. It's quite simple and for sure simpler that soldering wries - after this you can install JTAG adapter to repair as shown on video. You can buy additional molex connectors in future

Mounted JIG - ready for rock....



LInk to YouTube video from connection with Riff Box - uploading now.....
LInk to product: JTAG Samsung i5800 (Galaxy 3)
Link to 10 pin Molex to mount in phone: JTAG Molex 10pin

[Multi-COM]

JTAG LG P350 (Swift ME)





NOKOUT:
Adapter need to connect to molex connector on phone board - in 90% of cases PCB don't have this connector installed so you need to solder as on shown picture special 14 pin molex into it. It's quite simple and for sure simpler that soldering wries - after this you can install JTAG adapter to repair as shown on video. You can buy additional molex connectors in future



LInk to YouTube video from connection with Riff Box - LG P350 - JTAG/RIFF connection unbrick (repair dead boot) - YouTube
LInk to product: JTAG LG P350 (Swift ME)
Link to 14 pin Molex to mount in phone: JTAG Molex 14pin

[Multi-COM]

JTAG Samsung i7500 REVO.1 (Galaxy)



NOKOUT:
Adapter need to connect to molex connector on phone board - in 90% of cases PCB don't have this connector installed so you need to solder as on shown picture special 10 pin molex into it. It's quite simple and for sure simpler that soldering wries - after this you can install JTAG adapter to repair as shown on video. You can buy additional molex connectors in future

Mounted JIG - ready for rock....



LInk to YouTube video from unbrick with Riff Box - Samsung i7500 REVO.1 (Galaxy) - JTAG/RIFF connection unbrick (repair dead boot) - YouTube
LInk to product: JTAG Samsung i7500 REVO.1 (Galaxy)
Link to 10 pin Molex to mount in phone: JTAG Molex 10pin

[Multi-COM]

JTAG Samsung N7000 (Galaxy Note)



NOKOUT:
Adapter need to connect to molex connector on phone board - in 90% of cases PCB don't have this connector installed so you need to solder as on shown picture special 20 pin molex into it. It's quite simple and for sure simpler that soldering wries - after this you can install JTAG adapter to repair as shown on video. You can buy additional molex connectors in future


LInk to YouTube video from unbrick with Riff Box - Samsung N7000 (Galaxy Note) - JTAG/RIFF connection unbrick (repair dead boot) - YouTube
LInk to product: JTAG Samsung N7000 (Galaxy Note)
Link to 20 pin Molex to mount in phone: JTAG Molex 20pin

Its Price So High and Most of The Board Need to Sold MOLEX into. So need to lower price and Molexes with it.
Also make is availible on RIFF LOCAL Retailer

[huzein]

for me personally is easier to solder wire to small pins than to solder molex. for me this is not good solution. better do jtags like for i9000, this one is stable and good.

[Sethxp]

Originally Posted by huzein

for me personally is easier to solder wire

i must second that, for me too

[Multi-COM]

please note that Molex are soldered even in official Samsung service point - so if boot are demaged they also apply molex and then repair boot. For my personally soldering molex takes less than 1 minute.... and it's for sure more safe thaty wires... i see plently of phones with demaged pads due somone just take up wire and track (pad) from board goes off...... soldering are very simple: just clean pads, put flux, put molex on it and solder positioning pins... after this just solder pins.... similar as in TQFP chips etc...... if you will solder few then soldering next will be as a peace of cake

but everybody can choose if it's beter to solder wires or solder molex....

[Multi-COM]

JTAG Samsung i897 (Galaxy S Captivate)



NOKOUT:
Adapter need to connect to molex connector on phone board - in 90% of cases PCB don't have this connector installed so you need to solder as on shown picture special 12 pin molex into it. It's quite simple and for sure simpler that soldering wries - after this you can install JTAG adapter to repair as shown on video. You can buy additional molex connectors in future


LInk to YouTube video from unbrick with Riff Box - Samsung i897 (Galaxy S Captivate) - JTAG/RIFF connection unbrick (repair dead boot) - YouTube
LInk to product: JTAG Samsung i897 (Galaxy S Captivate)
Link to 20 pin Molex to mount in phone: JTAG Molex 12pin

[mikele09]

where buy jig jtag for samsung s2 in italy?

[forhike]

I like the new molex cables, but isnt posibly to mount molex connector on flexible cable?
the one used for unlocking htc?

Samsung kit.. 1pcs pcb connected to riff, then some difrent flexi cables with difrent molex connectors to be able to service new samsung phones.

Fit it al in custom plastic housing



B.r