Reliance zte mf190 How to recovery ?

[satrughna]

zte mf 190

1. no power on

2. nor red light blink

3. nor usb device detect

But there is no problem in detect with Riff box,

1. full dump flash

2. Resurrection

3. boot repair

no solution , any one plz help me on this


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.43
Selected Resurrector: [USB Modem MF190 V1.00]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK

Detected dead body ID: 0x301C00E1




Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.43
Selected Resurrector: [USB Modem MF190 V1.00]

Connecting to the target...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x301C00E1, IR Length = 0x04 bits
Total IR length: 0x0004 bits



Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.43
Selected Resurrector: [USB Modem MF190 V1.00]

Getting EmbeddedICE-RT registers...OK
00 = 0x00000010 08 = 0x00000000 10 = 0x00000000
01 = 0x00000000 09 = 0x00000000 11 = 0x00000000
02 = 0x00000000 0A = 0x00000000 12 = 0x00000000
03 = 0x00000000 0B = 0x00000000 13 = 0x00000000
04 = 0x60000000 0C = 0x00000000 14 = 0x00000000
05 = 0x00000000 0D = 0x000000F7 15 = 0x000000F7
06 = 0x60000000 0E = 0x00000000 16 = 0x00000000
07 = 0x00000000 0F = 0x00000000 17 = 0x00000000



Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.43
Selected Resurrector: [USB Modem MF190 V1.00]



Resetting target...OK
STATUS: Target is halted.

R0 = 0x0000004B R6 = 0x00002A00 R12 = 0x00004321
R1 = 0x80000000 R7 = 0x60000000 R13 = 0x7800FF58
R2 = 0x00000001 R8 = 0x00000236 R14 = 0x60000000
R3 = 0x00000015 R9 = 0x000088B6 R15 = 0xFFFF03F0
R4 = 0x00000200 R10 = 0x78000028 CPSR = 0x800000D3
R5 = 0x00000001 R11 = 0x00000240


there is above some detection result by riff. I tried 64mb full dump


Need soluton , plz help

[~AKSingh~]

First thing > Don't write full dump , as it can damage meid/imei area

Write 10-20% of dump area
replug modem
drivers will be detected
now flash with Official firmware /updater

This is what a resurrection does
so try not to write or erase full region

br,