Repaired/Unlocked GSM/UMTS/CDMA phones By RIFF JTAG - Page 90 - GSM-Forum

Imran Bhatti · 07-22-2012, 12:17

Htc Dream (G1) OK.
[7/22/2012 3:05:09 PM] [START OPERATION_ID = RESURRECT]
[7/22/2012 3:05:47 PM] Open serial port...OK
[7/22/2012 3:05:47 PM] Connecting to the RIFF Box...OK
[7/22/2012 3:05:47 PM] Firmware Version: 1.32, JTAG Manager Version: 1.43
[7/22/2012 3:05:47 PM] Selected Resurrector: [HTC Dream (G1) V1.00]
[7/22/2012 3:05:47 PM]
[7/22/2012 3:05:47 PM] Connecting to the dead body...OK
[7/22/2012 3:05:47 PM] Detected dead body ID: 0xA01700E1 - CORRECT!
[7/22/2012 3:05:47 PM] Set I/O Voltage reads as 2.60V, TCK Frequency is 4 MHz
[7/22/2012 3:05:47 PM]
[7/22/2012 3:05:47 PM] Resurrection sequence started.
[7/22/2012 3:05:47 PM] Establish communication with the phone...OK
[7/22/2012 3:05:47 PM] Initializing internal hardware configuration...OK
[7/22/2012 3:05:47 PM] Uploading resurrector data into memory...OK
[7/22/2012 3:05:47 PM] Starting communication with resurrector...OK
[7/22/2012 3:05:47 PM]
[7/22/2012 3:05:47 PM] Detected an Initialized FLASH1 Chip, ID: 0x00AD/0x55BA (256MB)
[7/22/2012 3:05:47 PM] Flashing the dead body...OK
[7/22/2012 3:05:47 PM] Resurrection complete!
[7/22/2012 3:05:47 PM] [FINISH OPERATION_ID = RESURRECT]

specas220 · 07-23-2012, 15:13

Hi, i would like to ask one question:
How can i unlock htc phone with Riff? Is it Posible with Riff unlock HTC sensation or other new model connected with USB cable or i need take it to pieces? thanks

louka · 07-24-2012, 00:18

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung I9003 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x0B6D602F - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)

Flashing the dead body...OK
Resurrection complete!

Nadoui · 07-24-2012, 13:37

Samsung S5560i

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung S5560i V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Flashing the dead body...OK
Resurrection complete!

dimityr.milev · 07-27-2012, 09:57

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [SE E15i V1.0.4463.41118]

Connecting to the dead body...OK
Detected dead body ID: 0x203C00E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x55BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Backup Important Zones...OK
Preparing data. Please wait...OK
Unlocking the Phone...OK
Unlock complete!

umoner · 07-27-2012, 16:03

Htc explorer repair ok

KIKO_GSM · 07-31-2012, 08:39

samsung s5360 white screen done via riff box

here help

Quote:

Resurrecting Samsung S5360 is easy. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5360:
Ø Solder JTAG cable to Samsung S5360 JTAG pads;
Ø Connect USB cable to phone and PC;
Ø Insert battery;
Ø Make sure Samsung S5360 is selected in the list of models;
Ø Click Resurrect button;
Ø Wait till software signals a successful operation completion;
Ø Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:
v Disconnect PC cable;
v Insert battery;
v Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
v If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

Most common errors:
v The NRST signal is not connected. Pease ALWAYS SOLDER THE NRST SIGNAL whenever it is present on the schematics. In case you have JIG please make sure NRST is routed, if not - solder wire manually.
v Connection is unstable or cannot be established at all. Please make sure JTAG wires are of the SAME LENGTH and total length of each wire not exceeds ~10...15 cm; make sure a fixed TCK frequency is selected (since device has no RTCK signal)

here working

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung S5360 V1.0.4443.1900]

Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 3.00V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB

Flashing the dead body...OK
Resurrection complete!

done

.::AZEEM::. · 08-01-2012, 12:37

MicroMax c100 blinking Successfully repaired in riff

Quote:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Micromax C100 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x122CE0E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0020/0x88C0 (8MB)
Selected Resurrection Data for the NOR Chip with IDs: 0x0020/0x88C0

Flashing the dead body...OK
Resurrection complete!

farodriguez · 08-03-2012, 04:54

Samsung Galaxy Ace Plus S7500L

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung S7500 V1.0.0.0]

Connecting to the dead body...OK
Detected dead body ID: 0x106230E1 - CORRECT!
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0000 (SJS00M, 0x0000E9000000 Bytes = 3.64 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0000 (SJS00M, 0x000000100000 Bytes = 1.00 MB)

Flashing the dead body...OK
Resurrection complete!

..::Afridi::.. · 08-03-2012, 07:57

Samsung SHV-E160K Galaxy Note LTE Dead Boot Repair Successfully by Riff Box. Thanks Riff and Teams.

Testpiont

-----------------------------------------------------------------------
Ruslt Screen short

Benhure · 08-04-2012, 11:55

i9100:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung i9100 V1.0.4582.4854]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 1 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Flashing the dead body...OK
Resurrection complete!

cellcare prasad · 08-06-2012, 08:31

ZTE S1602 SUCESSFULLY FLASHED

By prasadak2811 at 2012-08-06

HaNiNi Gsm · 08-07-2012, 08:18

thanks 2 riffbox team....after hard work in soldering JTAG i9000 and 2 i9003 boot repaired succefflly

this is logger

for i9000
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I9000 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete!

i9003

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung I9003 (via IRAM) V1.0.4464.49936]

Connecting to the dead body...OK
Detected dead body ID: 0x0B6D602F - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)

Flashing the dead body...OK
Resurrection complete!

dhiet · 08-07-2012, 15:19

Pantech (Verizon) PX-500/ PC5750 Modem Successfully read by Riff JTAG (many tanks to Legija for help)

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [MSM6XXX L06 D02 NAND V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x200720E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x04010009000000000000000004000000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00AD/0x0076 (64MB)

Reading FLASH1 address space from 0x000000000000 to 0x000003FFFFFF
Completed in 00:17:25.004 (Average Transfer Rate: 64.67 kB/s)

JTAG Pinout:

farodriguez · 08-08-2012, 00:20

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung P1000N V1.0.0.0]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete!

07-24-2012, 00:18	#1338 (permalink)
louka Temporary banned !! Join Date: Nov 2005 Posts: 2,945 Member: 198016 Status: Offline Sonork: 100.1602918 Thanks: 416 Thanked 11,879 Times in 2,325 Posts	I9003 ok Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.33, JTAG Manager Version: 1.44 Selected Resurrector: [Samsung I9003 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x0B6D602F - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete!

08-03-2012, 07:57	#1345 (permalink)
..::Afridi::.. Insane Poster Join Date: May 2012 Posts: 92 Member: 1756895 Status: Offline Thanks: 8 Thanked 8 Times in 8 Posts	..::Successfully Repair Boot Of Samsung E160K::.. Samsung SHV-E160K Galaxy Note LTE Dead Boot Repair Successfully by Riff Box. Thanks Riff and Teams. Testpiont ----------------------------------------------------------------------- Ruslt Screen short

08-06-2012, 08:31	#1347 (permalink)
cellcare prasad Product Supporter Join Date: Oct 2007 Location: VIZAG,A.P, INDIA Posts: 1,737 Member: 602547 Status: Offline Sonork: 100.1621466 Thanks: 172 Thanked 668 Times in 380 Posts	ZTE S1602 SUCESSFULLY FLASHED By prasadak2811 at 2012-08-06 By prasadak2811 at 2012-08-06

08-07-2012, 15:19	#1349 (permalink)
dhiet Freak Poster Join Date: Dec 2006 Location: indonesia Posts: 234 Member: 422015 Status: Offline Thanks: 113 Thanked 65 Times in 47 Posts	Pantech (Verizon) PX-500/ PC5750 Modem Successfully read by Riff JTAG (many tanks to Legija for help) Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.33, JTAG Manager Version: 1.44 Selected Resurrector: [MSM6XXX L06 D02 NAND V1.00] Connecting to the dead body...OK Detected dead body ID: 0x200720E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x04010009000000000000000004000000 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00AD/0x0076 (64MB) Reading FLASH1 address space from 0x000000000000 to 0x000003FFFFFF Completed in 00:17:25.004 (Average Transfer Rate: 64.67 kB/s) JTAG Pinout: Last edited by dhiet; 08-07-2012 at 15:26.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-23-2012, 15:13	#1337 (permalink)
specas220 Junior Member Join Date: Jul 2012 Posts: 3 Member: 1788555 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Hi, i would like to ask one question: How can i unlock htc phone with Riff? Is it Posible with Riff unlock HTC sensation or other new model connected with USB cable or i need take it to pieces? thanks

07-24-2012, 13:37	#1339 (permalink)
Nadoui Product Supporter Join Date: Jan 2010 Location: Paris Age: 37 Posts: 2,308 Member: 1202782 Status: Offline Sonork: 100.1608261 Thanks: 495 Thanked 501 Times in 467 Posts	Samsung S5560i Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung S5560i V1.00] Connecting to the dead body...OK Detected dead body ID: 0x07926F0F - CORRECT! Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...OK Resurrection complete!

07-27-2012, 09:57	#1340 (permalink)
dimityr.milev No Life Poster Join Date: Sep 2007 Location: Bulgaria,Assenovgrad Age: 35 Posts: 820 Member: 591325 Status: Offline Thanks: 38 Thanked 146 Times in 119 Posts	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [SE E15i V1.0.4463.41118] Connecting to the dead body...OK Detected dead body ID: 0x203C00E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x55BC (512MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Backup Important Zones...OK Preparing data. Please wait...OK Unlocking the Phone...OK Unlock complete!

08-04-2012, 11:55	#1346 (permalink)
Benhure Freak Poster Join Date: Oct 2001 Location: Earth Age: 28 Posts: 124 Member: 6884 Status: Offline Sonork: 100.1621477 Thanks: 98 Thanked 68 Times in 19 Posts	i9100: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.33, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung i9100 V1.0.4582.4854] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.80V, TCK Frequency is 1 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Flashing the dead body...OK Resurrection complete!

08-07-2012, 08:18	#1348 (permalink)
HaNiNi Gsm No Life Poster Join Date: Oct 2005 Location: Sousse /trockadero/TUNISIA Posts: 692 Member: 193003 Status: Offline Thanks: 26 Thanked 46 Times in 32 Posts	thanks 2 riffbox team....after hard work in soldering JTAG i9000 and 2 i9003 boot repaired succefflly this is logger for i9000 Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung I9000 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete! i9003 Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.33, JTAG Manager Version: 1.44 Selected Resurrector: [Samsung I9003 (via IRAM) V1.0.4464.49936] Connecting to the dead body...OK Detected dead body ID: 0x0B6D602F - CORRECT! Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete!

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	23	09-16-2012 23:57
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	16	02-01-2012 05:18
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	6	12-18-2011 11:00
need software for 5161 by cable	mln2000	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	6	08-29-2010 20:17