s5360L error

[Mujentujen]

Hi! A Samsung s5360l arrived to my local stuck in the Samsung S5360 Young logo and when i resurrect it says that:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.55
Selected Resurrector: [Samsung S5360 V1.0.4443.1900]

Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 2.99V, TCK Frequency is 4 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB

Flashing the dead body...OK
WARNING: Programming Error (0x24) at 0x00001FF00000 is handled as Cut Excess.
Resurrection complete!

But It keeps stuck, I'll try erase flash and full dump and says the same error, in the phone can enter in download mode only

[bruno santana]

the option of resurrection and dead cell
if so then try one wheel fulldump
believe will solve your problem
good luck

[Mujentujen]

CAn you tell me the process step by step?

[toninhosantos]

Originally Posted by Mujentujen

Hi! A Samsung s5360l arrived to my local stuck in the Samsung S5360 Young logo and when i resurrect it says that:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.55
Selected Resurrector: [Samsung S5360 V1.0.4443.1900]

Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 2.99V, TCK Frequency is 4 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB

Flashing the dead body...OK
WARNING: Programming Error (0x24) at 0x00001FF00000 is handled as Cut Excess.
Resurrection complete!

But It keeps stuck, I'll try erase flash and full dump and says the same error, in the phone can enter in download mode only

It's hardware problem, replace your emmc chip.

[Mujentujen]

But there's any way to get out of loop without that error? The error appears at 99%

[omi17]

Originally Posted by Mujentujen

Hi! A Samsung s5360l arrived to my local stuck in the Samsung S5360 Young logo and when i resurrect it says that:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.55
Selected Resurrector: [Samsung S5360 V1.0.4443.1900]

Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 2.99V, TCK Frequency is 4 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB

Flashing the dead body...OK
WARNING: Programming Error (0x24) at 0x00001FF00000 is handled as Cut Excess.
Resurrection complete!

But It keeps stuck, I'll try erase flash and full dump and says the same error, in the phone can enter in download mode only

Originally Posted by Mujentujen

But there's any way to get out of loop without that error? The error appears at 99%

Hii,
This error cause due to bad blocks in eMMC. Only Replacement is solution



__________________
Best Regards Omi17

[toninhosantos]

Originally Posted by Mujentujen

But there's any way to get out of loop without that error? The error appears at 99%

First change power key button
If not work, replace your emmc chip.

[Mujentujen]

I'll check it. Now i can enter in download mode but not in recovery to reset the phone.
The problem is that in my country it's not easy get eMMC chip