S7230E error restore

[wins13]

S7230E dead after flash.
Analyze jtag:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung S7230E V1.00]

Connecting to the target...OK
Set I/O Voltage reads as 2.80V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x07926F0F, IR Length = 0x04 bits
Device on TAP #1: ID = 0x07B3617F, IR Length = 0x05 bits
Total IR length: 0x0009 bits

Repair as S7230E

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung S7230E V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 4 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...FAILED
ERROR: Wrong response code from the RIFF Box: 0x4E


Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 2.78V, TCK Frequency is 12 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...FAILED
ERROR: Wrong response code from the RIFF Box: 0x4E

Connect as BCM2156

Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 2 MHz]
Settings Code: 0x1501000A000000000000000000000000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0054 (512MB)

Reading FLASH1 address space from 0x000000000000 to 0x00001FFFFFFF

[wins13]

Restore OK.
Flashed full S7230E as BCM2156:

Connecting to the dead body...OK
[27.07.2012 14:05:01] Detected dead body ID: 0x07B3617F - CORRECT!
[27.07.2012 14:05:01] Set I/O Voltage reads as 2.79V, TCK Frequency is RTCK
[27.07.2012 14:05:01] Adaptive Clocking RTCK Sampling is: [Sample at 6 MHz]
[27.07.2012 14:05:01] Settings Code: 0x3401000D000000000000000000000000
[27.07.2012 14:05:01]
[27.07.2012 14:05:01] Resurrection sequence started.
[27.07.2012 14:05:01] Establish communication with the phone...OK
[27.07.2012 14:05:01] Initializing internal hardware configuration...OK
[27.07.2012 14:05:01] Uploading resurrector data into memory...OK
[27.07.2012 14:05:01] Starting communication with resurrector...OK
[27.07.2012 14:05:01]
[27.07.2012 14:05:01] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0054 (512MB)
[27.07.2012 14:05:01]
[27.07.2012 14:05:01] Writting FLASH1 memory from 0x000000000000 to 0x00001FFFFFFF
[27.07.2012 14:05:01] WARNING: Programming Error (0x24) at 0x000005180000 is Ignored.
[27.07.2012 14:05:01] Completed in 01:11:26.266 (Average Transfer Rate: 126.14 kB/s)
[27.07.2012 14:05:01] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

Please fix dll for S7230E.