sam i9001 Resurrection problem - GSM-Forum

najegsm · 06-27-2012, 17:58

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I9001 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x27B360E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0000 (M8G2FA, 0x0001CD000000 Bytes = 7.20 GB)

Flashing the dead body...OK
Resurrection complete!

Resurrection DONE BUT NO DOWNLOAD MODE

ferhel · 06-27-2012, 18:06

Write Full Dump and post result.
i'm just wondering why so may cases like this, here in Riff section after resurrect not go to download mode :-?

easa · 06-28-2012, 21:25

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I9001 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x27B360E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0000 (M8G2FA, 0x0001CD000000 Bytes = 7.20 GB)

Flashing the dead body...OK
Resurrection complete!

Resurrection DONE, BUT NO DOWNLOAD MODE, only word "SAMSUNG" on display.

Any suggestions?

Pulka · 06-28-2012, 22:38

Hi.
You can try with USB JIG Adapter put in Download Mode.

BABAK NURI · 06-28-2012, 22:48

Maybe You Need Check Vol_Down key,Also Home Key......

-----
What is phone history?

easa · 06-28-2012, 23:19

I tryed with USB JIG Adapter 301k put in Download Mode - no success...

All buttons are intact.
When I press and hold the button combination appears Samsung logo, then the Samsung logo disappears after 5 seconds instead of the download mode appears again ...

Any suggestions?

BABAK NURI · 06-28-2012, 23:40

What is phone history...?

Are You sure You Have a Work USB_JIG...?Did you try check with another working phone..?

easa · 06-28-2012, 23:50

With this USB_JIG I repaired over 30 phones - JIG is working properly...

easa · 06-29-2012, 20:42

Problem solved by downloading part of fullflash at address 0 - 17FFFFFF and then download the firmware using Multuiloader...

tayyab007 · 06-30-2012, 08:59

Quote:

Originally Posted by easa

Problem solved by downloading part of fullflash at address 0 - 17FFFFFF and then download the firmware using Multuiloader...

dear can u guide me how to recover dead boot. because i repaired with riff and ort but phone does not go in download mode.

thanks and regards

asif

easa · 06-30-2012, 13:39

Go to the tab "dcc" and downloading to the phone part of fullflash at address 0 - 17FFFFFF and then download the firmware using Multuiloader. It's all...

sfantu007 · 01-26-2013, 19:39

I read these some address in flash but how to write

ponix · 05-03-2013, 19:03

please can shared full flash for i9001 i need it .

06-27-2012, 17:58	#1 (permalink)
najegsm Freak Poster Join Date: Sep 2005 Location: saudiarabia/india Posts: 447 Member: 185396 Status: Offline Sonork: 100.1618832 Thanks Meter: 33	sam i9001 Resurrection problem Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung I9001 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x27B360E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0000 (M8G2FA, 0x0001CD000000 Bytes = 7.20 GB) Flashing the dead body...OK Resurrection complete! Resurrection DONE BUT NO DOWNLOAD MODE

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	10-16-2013 08:16
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-21-1999 19:43
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

06-27-2012, 18:06	#2 (permalink)
ferhel No Life Poster Join Date: May 2007 Location: QC FAIRVIEW Posts: 1,111 Member: 504865 Status: Offline Thanks Meter: 213	Write Full Dump and post result. i'm just wondering why so may cases like this, here in Riff section after resurrect not go to download mode :-?

06-28-2012, 21:25	#3 (permalink)
easa Junior Member Join Date: Jul 2011 Posts: 10 Member: 1617728 Status: Offline Thanks Meter: 0	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.32, JTAG Manager Version: 1.43 Selected Resurrector: [Samsung I9001 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x27B360E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0000 (M8G2FA, 0x0001CD000000 Bytes = 7.20 GB) Flashing the dead body...OK Resurrection complete! Resurrection DONE, BUT NO DOWNLOAD MODE, only word "SAMSUNG" on display. Any suggestions?

06-28-2012, 22:38	#4 (permalink)
Pulka Freak Poster Join Date: Jan 2009 Location: Germany/NRW Posts: 420 Member: 936229 Status: Offline Sonork: 1606911 Thanks Meter: 115	Hi. You can try with USB JIG Adapter put in Download Mode.

06-28-2012, 22:48	#5 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Maybe You Need Check Vol_Down key,Also Home Key...... ----- What is phone history?

06-28-2012, 23:19	#6 (permalink)
easa Junior Member Join Date: Jul 2011 Posts: 10 Member: 1617728 Status: Offline Thanks Meter: 0	I tryed with USB JIG Adapter 301k put in Download Mode - no success... All buttons are intact. When I press and hold the button combination appears Samsung logo, then the Samsung logo disappears after 5 seconds instead of the download mode appears again ... Any suggestions?

06-28-2012, 23:40	#7 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	What is phone history...? Are You sure You Have a Work USB_JIG...?Did you try check with another working phone..?

06-28-2012, 23:50	#8 (permalink)
easa Junior Member Join Date: Jul 2011 Posts: 10 Member: 1617728 Status: Offline Thanks Meter: 0	With this USB_JIG I repaired over 30 phones - JIG is working properly...

06-29-2012, 20:42	#9 (permalink)
easa Junior Member Join Date: Jul 2011 Posts: 10 Member: 1617728 Status: Offline Thanks Meter: 0	Problem solved by downloading part of fullflash at address 0 - 17FFFFFF and then download the firmware using Multuiloader...

06-30-2012, 13:39	#11 (permalink)
easa Junior Member Join Date: Jul 2011 Posts: 10 Member: 1617728 Status: Offline Thanks Meter: 0	Go to the tab "dcc" and downloading to the phone part of fullflash at address 0 - 17FFFFFF and then download the firmware using Multuiloader. It's all...

01-26-2013, 19:39	#12 (permalink)
sfantu007 Major Poster Join Date: Feb 2006 Posts: 40 Member: 231253 Status: Offline Thanks Meter: 3	I read these some address in flash but how to write

05-03-2013, 19:03	#13 (permalink)
ponix No Life Poster Join Date: Feb 2006 Location: ALGERIA Posts: 984 Member: 229016 Status: Offline Sonork: 100.1590620 Thanks Meter: 130	please can shared full flash for i9001 i need it .