*** Samsung i9000 Galaxy S Repair - MEGA THREAD ! ! ! * * * - GSM-Forum

Hellosamir · 09-16-2010, 10:43

Can you highlight on board of I9000 Pinout photo Jtags, as i couldnot find it on photo.

your prompt help will be highly appreciated.

Regards
H.S

**legija** · 09-16-2010, 10:48

Hi,

What happens when You click "Interface Pinout" button ?

Hellosamir · 09-16-2010, 10:56

Quote:

Originally Posted by legija

Hi,

What happens when You click "Interface Pinout" button ?

I can see Picture of I9000 board and Pinout 1,2,4,5,6,7 and 8 but needs jtag points to connect hope u understand me.

Please highlight the Jtag points with marks on photo.

**legija** · 09-16-2010, 10:59

No, i dont understand.
JTAG Pins are already marked and highlighted. I dont see where is problem.

Hellosamir · 09-16-2010, 11:04

Quote:

Originally Posted by legija

No, i dont understand.
JTAG Pins are already marked and highlighted. I dont see where is problem.

Thanks for your support. If i am not mistaken the one marked with yellow 1,3,4 & 8, u mean that.

**legija** · 09-16-2010, 11:16

You first need to remove white compound from JTAG pads on PCB.
Then just COUNT from 1 to 8.

nics121 · 09-16-2010, 13:24

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.13, JTAG Manager Version: 1.14
Selected Resurrector: [Samsung I9000]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...
ERROR: Forced to Terminate. Terminated at 0x00000000

and software freezes - Need disconnect box and restart Jtag manager

**legija** · 09-16-2010, 13:26

Hi,

Do You know phone history ? Was it dead by flashing, or unknown reason ?

Mantikor · 09-16-2010, 14:38

I test yesterday on my absolutley work device - and same problem. I do fullflash backup, but after few seconds of data reading soft give error - RIFF box not answer... and phone power on... Need reconnect the box. I try on 2 computers many times. I don't try ressurection because phone work...

sen-i · 09-16-2010, 15:13

have you try enother frequenztoo? have some problem by flashing hd2 , but ufter change frequenz all was ok try enother frequenz and reply

nics121 · 09-16-2010, 15:18

Quote:

Originally Posted by legija

Hi,

Do You know phone history ? Was it dead by flashing, or unknown reason ?

unknown reason. I am not first who trying to revive it.

**legija** · 09-16-2010, 15:31

Can You try to read 0x00040000 size from phone ?
It looks like some problem related to NAND flash chip power supply.

nics121 · 09-16-2010, 15:46

connect & get ID

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.13, JTAG Manager Version: 1.14
Selected Resurrector: [Samsung I9000]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz
Model selected: SAMSUNG - Samsung I9000

Detected dead body ID: 0x1BA00477

read memory

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.13, JTAG Manager Version: 1.14
Selected Resurrector: [Samsung I9000]

Reading Target Memory...ERROR
ERROR: No response from the RIFF Box.

body visible only for 5-6 seconds.

amar181 · 09-16-2010, 16:04

hello samir I9000 pinout is clear,..........

Br.
amar181

**legija** · 09-16-2010, 16:12

Hi,

Use DCC TAB, ROM1 Address space to test memory read.

Thanks.

09-16-2010, 10:43	#1 (permalink)
Hellosamir Insane Poster Join Date: Feb 2006 Location: UK Posts: 99 Member: 233729 Status: Offline Thanks Meter: 13	***** Samsung i9000 Galaxy S Repair - MEGA THREAD ! ! ! * * * Can you highlight on board of I9000 Pinout photo** Jtags, as i couldnot find it on photo. your prompt help will be highly appreciated. Regards H.S

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Nokia "Contact Service" Repairer	Dirk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	10-04-2011 05:45
Repaired dead phone without backup	Prodigal	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	07-29-2011 11:26
Contact Service Repairer 1.2 by Bartek	Allen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	02-23-2011 09:00
5110 Contact Service Repairer via MBUS/FBUS	Allen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	11-15-2010 04:17
New!! Nokia Flash Checksum And Contact Service Repair	HookerGsM	Main Sales Section	0	01-02-2001 10:12

09-16-2010, 10:48	#2 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, What happens when You click "Interface Pinout" button ?

09-16-2010, 10:59	#4 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	No, i dont understand. JTAG Pins are already marked and highlighted. I dont see where is problem.

09-16-2010, 11:16	#6 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	You first need to remove white compound from JTAG pads on PCB. Then just COUNT from 1 to 8.

09-16-2010, 13:26	#8 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, Do You know phone history ? Was it dead by flashing, or unknown reason ?

09-16-2010, 14:38	#9 (permalink)
Mantikor Freak Poster Join Date: Aug 2002 Location: Belarus Age: 45 Posts: 373 Member: 14420 Status: Offline Thanks Meter: 54	I test yesterday on my absolutley work device - and same problem. I do fullflash backup, but after few seconds of data reading soft give error - RIFF box not answer... and phone power on... Need reconnect the box. I try on 2 computers many times. I don't try ressurection because phone work...

09-16-2010, 15:13	#10 (permalink)
sen-i Freak Poster Join Date: Nov 2008 Posts: 268 Member: 906499 Status: Offline Sonork: sen-i Thanks Meter: 47	have you try enother frequenztoo? have some problem by flashing hd2 , but ufter change frequenz all was ok try enother frequenz and reply

09-16-2010, 15:31	#12 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Can You try to read 0x00040000 size from phone ? It looks like some problem related to NAND flash chip power supply.

09-16-2010, 16:04	#14 (permalink)
amar181 No Life Poster Join Date: May 2007 Location: GSM WORLD Posts: 1,772 Member: 510122 Status: Offline Sonork: 100.1606547 Thanks Meter: 1,822	hello samir I9000 pinout is clear,.......... Br. amar181

09-16-2010, 16:12	#15 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, Use DCC TAB, ROM1 Address space to test memory read. Thanks.