samsung S2 riff resurection ok, but phone still dead ,not boot - GSM-Forum

skkeptik2 · 08-15-2012, 06:55

I have problem with Galaxy S2 (i9100)

here is log:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung i9100 V1.0.4582.4854]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)

Flashing the dead body...OK
Resurrection complete!

After that phone is not goes in download mode using three buttons (vol+ ,home,on/off)

i read resurection manual 10 times ,all steps like in manual but phone still dead, phone is almost new stops on update,and not repaired before...

abuqatadh · 08-15-2012, 09:40

bro try enter download mode by usb jig

or make it by your self here

*note you can found alot of resistor on broken board like nokia 5130

skkeptik2 · 08-15-2012, 11:18

Quote:

Originally Posted by abuqatadh

bro try enter download mode by usb jig

or make it by your self here

*note you can found alot of resistor on broken board like nokia 5130

i made 320 ohm resistors ..... jig from old charger cable..... and not goes to boot
f.u.c....n phone, need full dump to try write via riff, please , is not on torrents...

skkeptik2 · 08-15-2012, 15:53

Quote:

Originally Posted by skkeptik2

i made 320 ohm resistors ..... jig from old charger cable..... and not goes to boot
f.u.c....n phone, need full dump to try write via riff, please , is not on torrents...

i buy factory maded multi usb jig by gpg
same thing, other phones goes to boot imidetly, this not , i mean oter samsungs that i have in service

kwaku85 · 09-07-2012, 10:46

I have same problem. Resurrection can't help. Phone still dead. What to do now?

huzein · 09-07-2012, 11:01

try second resurrection option: initalize download mode

08-15-2012, 06:55	#1 (permalink)
skkeptik2 Freak Poster Join Date: Apr 2004 Age: 38 Posts: 201 Member: 63120 Status: Offline Thanks: 10 Thanked 47 Times in 26 Posts	samsung S2 riff resurection ok, but phone still dead ,not boot I have problem with Galaxy S2 (i9100) here is log: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.33, JTAG Manager Version: 1.44 Selected Resurrector: [Samsung i9100 V1.0.4582.4854] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB) Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB) Flashing the dead body...OK Resurrection complete! After that phone is not goes in download mode using three buttons (vol+ ,home,on/off) i read resurection manual 10 times ,all steps like in manual but phone still dead, phone is almost new stops on update,and not repaired before...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
6110 power does not stay on	sc~micro	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	5	04-10-2013 02:07
Phone Stuff for FREE & KEy-GEn For Logo Editor !	BoNtEk - ThA WtC MeMbA	Nokia Multimedia	10	03-11-2013 15:27
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	16	02-01-2012 05:18
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	6	12-18-2011 11:00

08-15-2012, 09:40	#2 (permalink)
abuqatadh No Life Poster Join Date: Nov 2006 Posts: 541 Member: 397296 Status: Offline Thanks: 1,462 Thanked 56 Times in 46 Posts	bro try enter download mode by usb jig or make it by your self here *note you can found alot of resistor on broken board like nokia 5130

09-07-2012, 10:46	#5 (permalink)
kwaku85 Freak Poster Join Date: Jan 2006 Location: Poland Age: 28 Posts: 362 Member: 219917 Status: Offline Thanks: 6 Thanked 25 Times in 21 Posts	I have same problem. Resurrection can't help. Phone still dead. What to do now?

09-07-2012, 11:01	#6 (permalink)
huzein Freak Poster Join Date: Nov 2006 Posts: 325 Member: 396421 Status: Offline Thanks: 88 Thanked 13 Times in 13 Posts	try second resurrection option: initalize download mode