samsung s259 not support wih riff? - GSM-Forum

monishtg · 12-29-2012, 07:55

i think last option for s259 is ort

feel_free · 12-29-2012, 14:50

yes u can recover your mobile through ORT box

gb2qaz · 10-09-2014, 09:13

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Huawei C5100 V1.00]
Restarting target (nRST Low then High)...OK

Connecting to the dead body...OK
Detected dead body ID: 0x200B20E1 - IGNORED!
Set I/O Voltage reads as 2.56V, TCK Frequency is 1 MHz
Settings Code: 0x26010609000000000000000002000000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x017E/0x2230 (32MB)

Writting FLASH1 memory from 0x000000000000 to 0x000001FFFFFF
WARNING: Programming Error (0x25) at 0x000000000000. Attempting to Repeat.
WARNING: Programming Error (0x25) at 0x000000000000. Attempting to Repeat.
ERROR: Reported Failure Code 0x25. Terminating at 0x000000000000

RIFF BOX SUPPORT S259 QSC6020 CPU

12-29-2012, 07:55	#1 (permalink)
monishtg Registered User Join Date: Jul 2008 Location: Ranchi Posts: 152 Member: 820646 Status: Offline Sonork: 100.1615032 Thanks Meter: 27	samsung s259 not support wih riff? i think last option for s259 is ort

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-29-2012, 14:50	#2 (permalink)
feel_free No Life Poster Join Date: May 2006 Location: Omer Mobile Shopee Age: 41 Posts: 554 Member: 272979 Status: Offline Sonork: 100.1607215 Thanks Meter: 135	yes u can recover your mobile through ORT box

10-09-2014, 09:13	#3 (permalink)
gb2qaz No Life Poster Join Date: Jan 2007 Posts: 582 Member: 441202 Status: Offline Thanks Meter: 120	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.37, JTAG Manager Version: 1.56 Selected Resurrector: [Huawei C5100 V1.00] Restarting target (nRST Low then High)...OK Connecting to the dead body...OK Detected dead body ID: 0x200B20E1 - IGNORED! Set I/O Voltage reads as 2.56V, TCK Frequency is 1 MHz Settings Code: 0x26010609000000000000000002000000 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x017E/0x2230 (32MB) Writting FLASH1 memory from 0x000000000000 to 0x000001FFFFFF WARNING: Programming Error (0x25) at 0x000000000000. Attempting to Repeat. WARNING: Programming Error (0x25) at 0x000000000000. Attempting to Repeat. ERROR: Reported Failure Code 0x25. Terminating at 0x000000000000 RIFF BOX SUPPORT S259 QSC6020 CPU