samsung s3310 boot repair problem - GSM-Forum

MOHIT_THAREJA · 03-23-2012, 12:09

samsung s3310 boot repair problem

dead in z3x then i try to repair with riff always show this error its 32mb chip inside

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.31, JTAG Manager Version: 1.41
Selected Resurrector: [Samsung S3310 V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0xA018/0xA018 (32MB)
Flashing the dead body...
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED
ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000

nettiboh · 03-23-2012, 12:12

may be this error is for bad pinout contact try to resolder bigger jumper wire...

**legija** · 03-23-2012, 12:44

This looks like dead flash chip. Check Your PCB for cracks or water damage.

deba-baya · 03-23-2012, 13:06

check in hardware .its flashchip problem

03-23-2012, 12:09	#1 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	samsung s3310 boot repair problem samsung s3310 boot repair problem dead in z3x then i try to repair with riff always show this error its 32mb chip inside Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.31, JTAG Manager Version: 1.41 Selected Resurrector: [Samsung S3310 V1.00] Connecting to the dead body...OK Detected dead body ID: 0x07926F0F - CORRECT! Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Resurrection sequence started. Establish communication with the phone...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0xA018/0xA018 (32MB) Flashing the dead body... ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	10-16-2013 08:16
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-21-1999 19:43
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

03-23-2012, 12:12	#2 (permalink)
nettiboh Freak Poster Join Date: Aug 2009 Location: butuan Posts: 134 Member: 1088357 Status: Offline Sonork: nettiboh Thanks Meter: 20	may be this error is for bad pinout contact try to resolder bigger jumper wire...

03-23-2012, 12:44	#3 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	This looks like dead flash chip. Check Your PCB for cracks or water damage.

03-23-2012, 13:06	#4 (permalink)
deba-baya Freak Poster Join Date: Mar 2010 Location: BBSR ODISHA INDIA Age: 37 Posts: 346 Member: 1273083 Status: Offline Sonork: 100.1619267 Thanks Meter: 36	check in hardware .its flashchip problem