Samsung s379 blinking, error in writing

[taturi1]

Hello

here is log

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.27, JTAG Manager Version: 1.36
Selected Resurrector: [QSC60XX L20 D08]
Connecting to the dead body...OK
Detected dead body ID: 0x220B30E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x0000010004000000000000000026
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x017E/0x223D (64MB)
Writting FLASH1 memory from 0x0000000000 to 0x0003FFFFFF
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Stopped due to multiple communication errors. Terminating at 0x0000000000


plz help. what to do?

Thanks

[M0YAL]

Hi,

Try With Direct JTAG Access to Flash Memory Plugin


http://forum.gsmhosting.com/vbb/f634...lugin-1399599/

[taturi1]

Originally Posted by M0YAL

Hi,

Try With Direct JTAG Access to Flash Memory Plugin


http://forum.gsmhosting.com/vbb/f634...lugin-1399599/

i can't understand. plz explain step by step.


Thanks

[M0YAL]

Originally Posted by taturi1

i can't understand. plz explain step by step.


Thanks

Short Manual how to Read/Write/Erase memory:

• Select chipset (MCU) used in the current target
• Select memory type and it’s host (MCU or MCU’s Embedded Memory Controller);
• Setup TCK/RTCK frequencies, JTAG I/O Voltage levels, target’s core position on the JTAG scan chain (TAP#);
• Connect target device to the RIFF BOX, make sure it has power, and click Connect & Flash ID button to ensure target device is connected and selected memory is initialized and visible;
• All further actions are completely same as is done when using DCC Read/Write page features

[MOHIT_THAREJA]

Originally Posted by M0YAL

Short Manual how to Read/Write/Erase memory:

• Select chipset (MCU) used in the current target
• Select memory type and it’s host (MCU or MCU’s Embedded Memory Controller);
• Setup TCK/RTCK frequencies, JTAG I/O Voltage levels, target’s core position on the JTAG scan chain (TAP#);
• Connect target device to the RIFF BOX, make sure it has power, and click Connect & Flash ID button to ensure target device is connected and selected memory is initialized and visible;
• All further actions are completely same as is done when using DCC Read/Write page features

i already try with direct plugin but not working means dump not writing s379 s259 or s399

[ali_imran]

Originally Posted by M0YAL

Short Manual how to Read/Write/Erase memory:

• Select chipset (MCU) used in the current target
• Select memory type and it’s host (MCU or MCU’s Embedded Memory Controller);
• Setup TCK/RTCK frequencies, JTAG I/O Voltage levels, target’s core position on the JTAG scan chain (TAP#);
• Connect target device to the RIFF BOX, make sure it has power, and click Connect & Flash ID button to ensure target device is connected and selected memory is initialized and visible;
• All further actions are completely same as is done when using DCC Read/Write page features

my problem solved thnx moyel

[ali_imran]

Originally Posted by MOHIT_THAREJA

i already try with direct plugin but not working means dump not writing s379 s259 or s399

all set working in riff

[boele servis]

direc memory programing plugin release version 1.04