samsung s379 dump writing problem - GSM-Forum

MOHIT_THAREJA · 10-26-2011, 09:52

samsung s379 dump writing problem

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.27, JTAG Manager Version: 1.36
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x220B30E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x0900010001000000000000000026

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x017E/0x223D (64MB)

Writting FLASH1 memory from 0x0000000000 to 0x0003FFFFFF
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Stopped due to multiple communication errors. Terminating at 0x0000000000

SkyMobile05 · 10-26-2011, 10:09

sam problem with samsung S7230E

MOHIT_THAREJA · 10-26-2011, 11:39

here is log of nand dll

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.27, JTAG Manager Version: 1.36
Selected Resurrector: [QSC6XXX L36 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x220B30E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x0900010003FFFFFF00000000002A

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: Memory access timed out.

ranjeet92 · 10-26-2011, 12:30

need pinout for this model please

MOHIT_THAREJA · 10-26-2011, 12:59

Quote:

Originally Posted by ranjeet92

need pinout for this model please

here is your pinout

samsung s379

MOHIT_THAREJA · 11-02-2011, 09:32

samsung s379 recover done ...

avtarkaint · 12-06-2011, 16:48

how did you recovered it....?

Imrankhan · 12-14-2011, 09:56

same here

Connecting to the dead body...OK
Detected dead body ID: 0x220B30E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 4 MHz]
Settings Code: 0x0C00010000800000000000000024

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x017E/0x223D (64MB)

Writting FLASH1 memory from 0x0000000000 to 0x0003FFFFFF
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...

10-26-2011, 09:52	#1 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	samsung s379 dump writing problem samsung s379 dump writing problem Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.27, JTAG Manager Version: 1.36 Selected Resurrector: [QSC60XX L20 D08] Connecting to the dead body...OK Detected dead body ID: 0x220B30E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x0900010001000000000000000026 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x017E/0x223D (64MB) Writting FLASH1 memory from 0x0000000000 to 0x0003FFFFFF ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Stopped due to multiple communication errors. Terminating at 0x0000000000

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Eeprom dump lost, help needed.	CAMILO	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	11-29-2010 19:04
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

10-26-2011, 10:09	#2 (permalink)
SkyMobile05 No Life Poster Join Date: May 2007 Location: Algerie,Batna Posts: 786 Member: 508860 Status: Offline Sonork: 1613186 Thanks Meter: 224	sam problem with samsung S7230E

10-26-2011, 11:39	#3 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	here is log of nand dll Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.27, JTAG Manager Version: 1.36 Selected Resurrector: [QSC6XXX L36 D08] Connecting to the dead body...OK Detected dead body ID: 0x220B30E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x0900010003FFFFFF00000000002A Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...FAILED ERROR: Memory access timed out.

10-26-2011, 12:30	#4 (permalink)
ranjeet92 Freak Poster Join Date: Feb 2010 Posts: 198 Member: 1246160 Status: Offline Sonork: 100.1651488 Thanks Meter: 7	need pinout for this model please

11-02-2011, 09:32	#6 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	samsung s379 recover done ...

12-06-2011, 16:48	#7 (permalink)
avtarkaint No Life Poster Join Date: Feb 2007 Location: COOLSAND CPU Posts: 1,844 Member: 452162 Status: Offline Sonork: 100.1592470 Thanks Meter: 440	how did you recovered it....?

12-14-2011, 09:56	#8 (permalink)
Imrankhan No Life Poster Join Date: Aug 2007 Location: world Posts: 1,913 Member: 573962 Status: Offline Sonork: 100.1603021 Thanks Meter: 480	same here Connecting to the dead body...OK Detected dead body ID: 0x220B30E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 4 MHz] Settings Code: 0x0C00010000800000000000000024 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x017E/0x223D (64MB) Writting FLASH1 memory from 0x0000000000 to 0x0003FFFFFF ERROR: Timeout while waiting for DCC Loader response. Trying to recover...