Samsung S5690 pinout - GSM-Forum

akome · 07-24-2012, 22:31

Hi, I have a S5690 dead, but I can't find the correct pinout, if someone can share it, it will be gratefull

BABAK NURI · 07-25-2012, 11:49

Hi
Please Take high resulotion photo...Then post here or send to me via sonork

akome · 07-26-2012, 17:07

ok I will take it

akome · 07-26-2012, 17:40

waiting for sending it via sonork

akome · 07-30-2012, 17:07

Any ideas, Mr. babak picture sent. and Mr. Legija no news about this resurrector?

tedicomsa · 07-31-2012, 05:08

Only on in samsung image.

This repairs?

BABAK NURI · 07-31-2012, 22:36

Hi akome

Did You Test Pinout...?
If pinout work,Please Read Full Flash Size,Then Upload and give me link

Here is Pinout(Need Test):
http://s3.picofile.com/file/7455137739/13.png

akome · 08-01-2012, 21:35

will test by tomorrow or later, I will feed any news here

akome · 08-03-2012, 23:02

Tested... Marvell MG2 CPU not in list on custom targets... for readout, anyone please advice...

akome · 08-06-2012, 16:08

Downloaded Marvell PXA3XXX NAND, but no answer will resolder wires, and by the way that's the correct pinout MR. Babak?

**legija** · 08-06-2012, 19:25

Hi,
This cpu is not officially supported yet. Not much info about it, it's single core @800Mhz, and nothing more.

akome · 08-06-2012, 22:30

Ah crap... so there is no way to resurrect it Legija?

gabi_harlem · 08-10-2012, 00:11

Hy! i have one S5690 killed with bad firmware...and now only samsung logo appear can't get boot logo with any combination, and also no succes with rezistor at ground...Please help...!!!!

akome · 08-11-2012, 16:42

same problem as me friend, we have to wait...

tentacool · 09-05-2012, 16:44

same problem as me

pls any sugestion!!

07-24-2012, 22:31	#1 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	Samsung S5690 pinout Hi, I have a S5690 dead, but I can't find the correct pinout, if someone can share it, it will be gratefull

07-31-2012, 05:08	#6 (permalink)
tedicomsa Junior Member Join Date: Jul 2006 Posts: 4 Member: 309687 Status: Offline Thanks: 2 Thanked 9 Times in 1 Post	Please urgent need driver tavor obm s5690l Only on in samsung image. This repairs?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
8810 pinout??	timitiz	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	2	06-11-2012 11:10
Please Help, Pinout of N8810	mobileinfo	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	5	06-30-2010 15:53
needed pinout for carkit(N61xx)	mobileinfo	Nokia Hardware & Hardware-Repair Area	1	12-27-2006 10:20
8810 pinouts for dejan flasher !?!?!?	makona	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	0	08-03-2001 04:39
8850 pinouts	MDR	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	4	12-30-2000 00:23

07-25-2012, 11:49	#2 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 32 Posts: 5,264 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks: 534 Thanked 1,569 Times in 1,021 Posts	Hi Please Take high resulotion photo...Then post here or send to me via sonork

07-26-2012, 17:07	#3 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	ok I will take it

07-26-2012, 17:40	#4 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	waiting for sending it via sonork

07-30-2012, 17:07	#5 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	Any ideas, Mr. babak picture sent. and Mr. Legija no news about this resurrector?

07-31-2012, 22:36	#7 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 32 Posts: 5,264 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks: 534 Thanked 1,569 Times in 1,021 Posts	Hi akome Did You Test Pinout...? If pinout work,Please Read Full Flash Size,Then Upload and give me link Here is Pinout(Need Test): http://s3.picofile.com/file/7455137739/13.png

08-01-2012, 21:35	#8 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	will test by tomorrow or later, I will feed any news here

08-03-2012, 23:02	#9 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	Tested... Marvell MG2 CPU not in list on custom targets... for readout, anyone please advice...

08-06-2012, 16:08	#10 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	Downloaded Marvell PXA3XXX NAND, but no answer will resolder wires, and by the way that's the correct pinout MR. Babak?

08-06-2012, 19:25	#11 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 44 Posts: 4,593 Member: 256342 Status: Offline Sonork: 100.45940 Thanks: 130 Thanked 24,229 Times in 1,970 Posts	Hi, This cpu is not officially supported yet. Not much info about it, it's single core @800Mhz, and nothing more.

08-06-2012, 22:30	#12 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	Ah crap... so there is no way to resurrect it Legija?

08-10-2012, 00:11	#13 (permalink)
gabi_harlem Freak Poster Join Date: Jul 2005 Location: Romania Age: 30 Posts: 195 Member: 163459 Status: Offline Thanks: 11 Thanked 23 Times in 14 Posts	Hy! i have one S5690 killed with bad firmware...and now only samsung logo appear can't get boot logo with any combination, and also no succes with rezistor at ground...Please help...!!!!

08-11-2012, 16:42	#14 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks: 8 Thanked 4 Times in 4 Posts	same problem as me friend, we have to wait...

09-05-2012, 16:44	#15 (permalink)
tentacool Insane Poster Join Date: Aug 2003 Location: romania Age: 34 Posts: 60 Member: 37233 Status: Offline Thanks: 4 Thanked 4 Times in 3 Posts	same problem as me pls any sugestion!!