SGH-I727: can read JTAG chain but can't connect to dead body

[topprospect]

I am trying to resurrect a SGH-I727 Skyrocket. The RIFF box can read the JTAG chain out properly as seen here:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
  Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
  Device on TAP #1: ID = 0x106A10E1, IR Length = 0x0B bits
Total IR length: 0x000F bits

From other posts, I know these are the correct ID values. But when I attempt the resurrection, it fails to connect to the dead body:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the dead body...FAILED
None is detected.

I can confirm that the device is powered since I see Qualcomm US-USB QDLoader in XP's Device Manager and if I remove the USB then I cannot even read out the JTAG chain.

What else could be wrong? Any suggestions would be much appreciated! Thanks.

[topprospect]

Bump! Any ideas out there? I have run out of things I know to try.

[legija]

Reset phone power, and quickly press "resurrection" button.

[alex89]

tried this but not working

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the dead body...OK
Detected dead body ID: 0x106A10E1 - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: No response from the RIFF Box.

[ikkks]

Originally Posted by topprospect

I am trying to resurrect a SGH-I727 Skyrocket. The RIFF box can read the JTAG chain out properly as seen here:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
  Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
  Device on TAP #1: ID = 0x106A10E1, IR Length = 0x0B bits
Total IR length: 0x000F bits

From other posts, I know these are the correct ID values. But when I attempt the resurrection, it fails to connect to the dead body:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.43
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the dead body...FAILED
None is detected.

I can confirm that the device is powered since I see Qualcomm US-USB QDLoader in XP's Device Manager and if I remove the USB then I cannot even read out the JTAG chain.

What else could be wrong? Any suggestions would be much appreciated! Thanks.

ME TOO SAME PROBLEM WHY WE HAVE THIS ISSUE WITH SOME MODELS T989 ALSO SAME PROBLEM WHICH I HAVE RETURN TO MY CUST WITHOUT REPAIRING IT ..... can anybody explain here y this problem with RIFF is it dll problem or what

analyze chain log ...


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
Device on TAP #1: ID = 0x106A10E1, IR Length = 0x0B bits
Total IR length: 0x000F bits


but Resurrection says

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.33, JTAG Manager Version: 1.44
Selected Resurrector: [Samsung I727 V1.0.4455.8370]

Connecting to the dead body...FAILED
None is detected.

[BABAK NURI]

Hi
@ ikkks
--
I Think You Need Check Pinout Solder,Also Connect Only USB Cable(witout battrey or power supply).Then Press "Resurrect"...And Post Result
Some case of APQ8060 can't detect with battery or P.S
--
if you have still problem,Please contact me via sonork

[ysr84]

Originally Posted by BABAK NURI

Hi
@ ikkks
--
I Think You Need Check Pinout Solder,Also Connect Only USB Cable(witout battrey or power supply).Then Press "Resurrect"...And Post Result
Some case of APQ8060 can't detect with battery or P.S
--
if you have still problem,Please contact me via sonork

I am getting the following


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.48
Selected Resurrector: [Samsung I727 V1.0.4455.8370]
Connecting to the dead body...OK
Detected dead body ID: 0x106A10E1 - CORRECT!
Set I/O Voltage reads as 1.81V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...FAILED
ERROR: Wrong DCC data length received.