T919 repair ok but can't flash ffs

[..::Thanh_gsm::..]

I receive two T919 phones dead by flash F480 sw.
Riff repair ok but after that can't flash ffs.
I use mulltiloader, nspro, Z3x, SPt box too.

Is it Riff has problem?

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.13, JTAG Manager Version: 1.14
Selected Resurrector: [Samsung T919]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Model selected: SAMSUNG - Samsung T919

Detected dead body ID: 0x101C00E1


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.13, JTAG Manager Version: 1.14
Selected Resurrector: [Samsung T919]

Connecting to the dead body...OK
Detected dead body ID: 0x101C00E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x005C (512MB)
Flashing the dead body...OK
Resurrection complete!

[..::Thanh_gsm::..]

Be sad about supportter, chat through sonork - no answer, post here still really get no answer too.

[legija]

Hi,
Supporter cannot answer same minute You have problem.
This is not RIFF problem, since You can enter boot mode, but it might be fixable with RIFF.

Make the full dump from phone now, and contact me for FTP details to upload it, we need to check it.

[..::Thanh_gsm::..]

Originally Posted by legija

Hi,
Supporter cannot answer same minute You have problem.
This is not RIFF problem, since You can enter boot mode, but it might be fixable with RIFF.

Make the full dump from phone now, and contact me for FTP details to upload it, we need to check it.

Flash size is 512mb and I only can read it at 400khz speed
I try and software said it takes 5 hours to read done.

I have dump boot file from ort, can i use it?

[legija]

Hi,
That is not normal, so better check the cables and connection.

Also, how is it 400KHz if from resurrection log i can see RTCK is at Max ?

Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

[..::Thanh_gsm::..]

Originally Posted by legija

Hi,
That is not normal, so better check the cables and connection.

Also, how is it 400KHz if from resurrection log i can see RTCK is at Max ?

resurrection ok at max speead but when try to get dump, only 400khz ok sir.

Sorry my pc has not usb port left to take screenshot now.

[..::Thanh_gsm::..]

He he , fcuk to the end and I get successfully.

Download Start Ch[0]
OemSbl 407.1KB OK[2.2s]
QcSblHd 1.3KB OK[0.3s]
Mibib1 22.5KB OK[0.3s]
Mibib2 22.5KB OK[0.3s]
QcSbl 45.6KB OK[0.4s]
Wait reset !!
Rsrc1 23854.9KB OK[101.7s]
Rsrc2 525.7KB OK[3.1s]
FFS 47102.5KB OK[200.4s]
All files complete[320.9s]

1) repair by riff.
2) flash by multiloader will get error ffs, now phone display download ffs.bin again.
3) let phone in that stituation and repair again by riff.
4) flash by multiloader without AMSS

[..::Thanh_gsm::..]

If I don't repair twice by riff, always get this error too.

Download Start Ch[0]
OemSbl 407.1KB OK[3.0s]
QcSblHd 1.3KB OK[0.3s]
Mibib1 22.5KB OK[0.5s]
Mibib2 22.5KB OK[0.4s]
QcSbl 45.6KB OK[0.5s]
Wait reset !!
Rsrc1 23854.9KB OK[90.7s]
Rsrc2 525.7KB OK[3.1s]
ERR : NAK_FLASH_ERROR 0
ERR : NAK_FLASH_ERROR 0
Error : FFS Write [3.2s]

[hoang]

It seems partition untouch!

[tienquyen]

i was flashing with nspro, z3x samsung, multiflashloader,and...... but not flash fft . pro! solution?

[deepakgarg]

if phone can enter bootloader just flash phone with boot files from same version u want to flash phone