T959 Resurrection Error - GSM-Forum

akome · 08-05-2011, 22:22

Hi legija, thanks for the box, excellent device!!
I'm facing this error what it could be...

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.34
Selected Resurrector: [Samsung T959]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 18 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...
ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...OK
ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...OK
ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...OK
ERROR: Stopped due to multiple communication errors. Terminating at 0x0000000000

**legija** · 08-05-2011, 22:50

I think 18MHz for TCK is not enough, check if there is 3.9Ghz and set it.

akome · 08-05-2011, 23:08

Sorry was my bad! I rewired the points, repeated the process, and went successful, but the phone it doesn't turn on... It was turning on, but he has several failures about signal, was completely software, then I tought to resurrect it to have it in the initial state...

08-05-2011, 22:22	#1 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks Meter: 4	T959 Resurrection Error Hi legija, thanks for the box, excellent device!! I'm facing this error what it could be... Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.34 Selected Resurrector: [Samsung T959] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.79V, TCK Frequency is 18 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB) Flashing the dead body... ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...OK ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...OK ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...OK ERROR: Stopped due to multiple communication errors. Terminating at 0x0000000000

08-05-2011, 23:08	#3 (permalink)
akome Freak Poster Join Date: Feb 2008 Posts: 102 Member: 708255 Status: Offline Thanks Meter: 4	Sorry was my bad! I rewired the points, repeated the process, and went successful, but the phone it doesn't turn on... It was turning on, but he has several failures about signal, was completely software, then I tought to resurrect it to have it in the initial state... Last edited by akome; 08-05-2011 at 23:17.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
where to find a working program all they have some errors ??	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	12-12-2012 13:26
My 5110 v5.11 have a strange error.., it resets it self every 60second	luuk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	24	08-11-2006 15:29
Avoid 3 times error code in Nokia 6185	X-plot	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	05-08-2000 20:24
The multiple errors of Winlock ... ???	Genata	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	09-20-1999 19:12
error (1002) simlock3.dll winopen	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	08-28-1999 15:57

08-05-2011, 22:50	#2 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	I think 18MHz for TCK is not enough, check if there is 3.9Ghz and set it.