X10I AFTER Resurrection complete STILL RED LIGHT BLINKING - GSM-Forum

zablon · 04-06-2012, 09:29

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.31, JTAG Manager Version: 1.41
Selected Resurrector: [SE X10i V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x002C/0x55B3 (1024MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Preparing data. Please wait...OK
Flashing the dead body...OK
Resurrection complete!
pls supporter help me. what i have to do?

BABAK NURI · 04-06-2012, 11:43

why not use search button before start new thread

if not power on after resurrect ,you need reflash phone
if not power on after reflash its hw problem
if you can't flash phone because damaged flash chip

Jani-Jan · 04-06-2012, 13:33

try to repair imei and unlock with riff tested

after this flash.

zablon · 04-06-2012, 15:21

Quote:

Originally Posted by Jani-Jan

try to repair imei and unlock with riff tested

after this flash.

i did it all i search every where

04-06-2012, 09:29	#1 (permalink)
zablon No Life Poster Join Date: Jan 2008 Location: ETHIOPIA Posts: 725 Member: 688223 Status: Offline Sonork: 1000.1603261 Thanks Meter: 143	X10I AFTER Resurrection complete STILL RED LIGHT BLINKING Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.31, JTAG Manager Version: 1.41 Selected Resurrector: [SE X10i V1.00] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x002C/0x55B3 (1024MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Preparing data. Please wait...OK Flashing the dead body...OK Resurrection complete! pls supporter help me. what i have to do?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
BLUE light	Delfo	Nokia Hardware & Hardware Repair	8	09-20-2002 04:28
5110/6110 after unlocking see only network to which it was locked and ...	2M	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	07-25-2000 00:51
5110 5.24 locked all 4 locks after unlocking...	MCG	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	03-07-2000 22:24
Still with nokia 5110 ver 5.24	VirtualM	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	11-11-1999 18:57
DOES THE CELLNET DIGA HACK STILL WORK???	SP UNLOCKER 2000	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	10-04-1999 13:55

04-06-2012, 11:43	#2 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	why not use search button before start new thread if not power on after resurrect ,you need reflash phone if not power on after reflash its hw problem if you can't flash phone because damaged flash chip

04-06-2012, 13:33	#3 (permalink)
Jani-Jan No Life Poster Join Date: Jan 2003 Location: GMT +5 Age: 49 Posts: 1,230 Member: 19737 Status: Offline Thanks Meter: 133	try to repair imei and unlock with riff tested after this flash.