Lumia 1520 flashing error - GSM-Forum

:::luckyboy::: · 07-26-2014, 11:18

Hi Best dongle team ,

I've a Lumia 1520 RM-937 .It was blinking on nokia logo when i flashed this phone suddenly it went off and it's asking for (QHUSB_BULK ) drivers now .

What kind of these drivers .I've been checked on support but there isn't any type of these drivers.

Where can i get these drivers or what's the solution to solve this problem ?

Dzirt · 07-26-2014, 11:47

Hello.
Can you post flashing logs? Need check them to determine problem.

:::luckyboy::: · 07-26-2014, 11:58

I didn't save that error logo . I can't send you new logo until it will not detect with software because it's asking for (QHUSB_BULK ) drivers.

Dzirt · 07-26-2014, 12:52

Logs inside BEST/logs/ folder

:::luckyboy::: · 07-26-2014, 17:01

This is that log ,

Waiting for phone...
Dead mode is selected , no phone in normal mode found
1. Press and hold : "Volume Down" + "Power On"
2. Insert USB cable
3. When cable connected and you feel short vibra - release buttons

Device catched in BOOT mode!
Boot Mode confirmed!
Setting Preloder
Collect Info...
Setting Application
Setting Secure
Collect Info...
=== Nokia Flash App info :
Protocol Version : 2.20
Protocol Implementation : 2.37
=== Phone Initial info :
Phone RMxxx ID : RM-937
Phone Model ID : Nokia.MSM8974.P6081.2.2
Phone Model PC : 059V254
Phone IMEI : 358342051215741
=== eMMC info :
eMMC Vendor : Samsung
eMMC CID : 0015
eMMC Size : 29820 MiB
=== Security Initial info :
Security Status : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey : 3774964A7E6AC7EF7D428DDC0C0EAD71640B0D8D
=== Other info :
SD present : False

FFU : RM937_1028.3562.1402.0018_RETAIL_apac_sea_206_18_3 74887_prd_signed.ffu
Checking...
Override Software RRKH check , will check via Signature
Device ProductID Match with FFU ProductID!
ProductID : Nokia.MSM8974.P6081
DevRKH : 3774964A7E6AC7EF7D428DDC0C0EAD71640B0D8D
All Ok, Continue flashing...

FFU : RM937_1028.3562.1402.0018_RETAIL_apac_sea_206_18_3 74887_prd_signed.ffu
Flashing FFU
Sending FFU Header CertData
Header sent , accepted

Perform Data Partition Erase
Erase done
Sending FFU Payload Data...
Error, stop at : 0x0006 , reason : NO ACK !!!
Red Light

Error during flashing!

Dzirt · 07-26-2014, 17:35

Sadly, but seems as battery/cable fault.
At now need repair via some eMMC or Jtag device (bootloader) , charge phone fully , and flash again after.

:::luckyboy::: · 07-26-2014, 17:44

ohh it's bad ,

let me change the battery or i will check with JTAG .

Thank you .

Dzirt · 07-26-2014, 18:23

At now battery not recover anything , bootloader is already damaged

Need repair it, charge battery, get good short cable and flash again.
After all will work.

SandyBridge · 12-28-2016, 17:24

RPMB Provision Status Code : 0x0101
Device RAM size : 1024 MiB
Device not have ATRP
Backup to RAM Ok!

FFU : RM1089_02074.00000.15234.28003_RETAIL_prod_signed_ 1056_0260D5_HUT-GB.ffu
Flashing FFU
Sending FFU Header CertData
Header sent , accepted

Perform Data Partition Erase
Error : 06 : Data Partition Not Found! Seems as damaged
Will Fix partitions by flash whole image
Sending FFU Header CertData
Header sent , accepted

Skip Data Partition Erase
Sending FFU Payload Data...
Error, stop at : 0x0009 , reason : NO ACK !!!
Connection broken due some HW reasons ( like empty battery or cable ) or drivers problem!
Red Light

Error during flashing!
[Info] : Check previous message carefully , follow given advises
[Info] : Recommended to not power off device, if it shows "RED SCREEN"
[Info] : After problems will be fixed - tick "Recovery" and repeat flashing again!

Connect phone on selected interface...

JayDi · 12-29-2016, 14:54

Read log. Follow it.

trustunlockc · 03-22-2017, 15:30

Error, stop at : 0x0043 , reason : NO ACK !!!

trustunlockc · 03-22-2017, 15:30

SECWIM : RM1072_2179.0000.9651.15148.207.725_enosw-wim-signed_825027.secwim
Sending WIM ...
Error, stop at : 0x0043 , reason : NO ACK !!!
Init Error

Error during Init TestMode!

Connect phone on selected interface...

JayDi · 03-22-2017, 15:53

Charge battery. Use original short USB cable, direct connection to board with NO hubs.

07-26-2014, 11:18	#1 (permalink)
:::luckyboy::: Freak Poster Join Date: Mar 2009 Posts: 220 Member: 994230 Status: Offline Thanks Meter: 19	Lumia 1520 flashing error Hi Best dongle team , I've a Lumia 1520 RM-937 .It was blinking on nokia logo when i flashed this phone suddenly it went off and it's asking for (QHUSB_BULK ) drivers now . What kind of these drivers .I've been checked on support but there isn't any type of these drivers. Where can i get these drivers or what's the solution to solve this problem ?

07-26-2014, 11:47	#2 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	Hello. Can you post flashing logs? Need check them to determine problem.

07-26-2014, 11:58	#3 (permalink)
:::luckyboy::: Freak Poster Join Date: Mar 2009 Posts: 220 Member: 994230 Status: Offline Thanks Meter: 19	I didn't save that error logo . I can't send you new logo until it will not detect with software because it's asking for (QHUSB_BULK ) drivers.

07-26-2014, 12:52	#4 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	Logs inside BEST/logs/ folder

07-26-2014, 17:01	#5 (permalink)
:::luckyboy::: Freak Poster Join Date: Mar 2009 Posts: 220 Member: 994230 Status: Offline Thanks Meter: 19	This is that log , Waiting for phone... Dead mode is selected , no phone in normal mode found 1. Press and hold : "Volume Down" + "Power On" 2. Insert USB cable 3. When cable connected and you feel short vibra - release buttons Device catched in BOOT mode! Boot Mode confirmed! Setting Preloder Collect Info... Setting Application Setting Secure Collect Info... === Nokia Flash App info : Protocol Version : 2.20 Protocol Implementation : 2.37 === Phone Initial info : Phone RMxxx ID : RM-937 Phone Model ID : Nokia.MSM8974.P6081.2.2 Phone Model PC : 059V254 Phone IMEI : 358342051215741 === eMMC info : eMMC Vendor : Samsung eMMC CID : 0015 eMMC Size : 29820 MiB === Security Initial info : Security Status : 010100000101 Secure Boot : Enabled Secure eFUSE : Enabled JTAG : Disabled RDC Key : Not Present (Retail) UEFI SBoot : Enabled SecHW Key : Exists Device RootKey : 3774964A7E6AC7EF7D428DDC0C0EAD71640B0D8D === Other info : SD present : False FFU : RM937_1028.3562.1402.0018_RETAIL_apac_sea_206_18_3 74887_prd_signed.ffu Checking... Override Software RRKH check , will check via Signature Device ProductID Match with FFU ProductID! ProductID : Nokia.MSM8974.P6081 DevRKH : 3774964A7E6AC7EF7D428DDC0C0EAD71640B0D8D All Ok, Continue flashing... FFU : RM937_1028.3562.1402.0018_RETAIL_apac_sea_206_18_3 74887_prd_signed.ffu Flashing FFU Sending FFU Header CertData Header sent , accepted Perform Data Partition Erase Erase done Sending FFU Payload Data... Error, stop at : 0x0006 , reason : NO ACK !!! Red Light Error during flashing!

07-26-2014, 17:35	#6 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	Sadly, but seems as battery/cable fault. At now need repair via some eMMC or Jtag device (bootloader) , charge phone fully , and flash again after.

07-26-2014, 17:44	#7 (permalink)
:::luckyboy::: Freak Poster Join Date: Mar 2009 Posts: 220 Member: 994230 Status: Offline Thanks Meter: 19	ohh it's bad , let me change the battery or i will check with JTAG . Thank you .

07-26-2014, 18:23	#8 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	At now battery not recover anything , bootloader is already damaged Need repair it, charge battery, get good short cable and flash again. After all will work.

12-28-2016, 17:24	#9 (permalink)
SandyBridge Freak Poster Join Date: May 2015 Location: Algiers, Algeria Posts: 343 Member: 2399672 Status: Offline Thanks Meter: 187	RPMB Provision Status Code : 0x0101 Device RAM size : 1024 MiB Device not have ATRP Backup to RAM Ok! FFU : RM1089_02074.00000.15234.28003_RETAIL_prod_signed_ 1056_0260D5_HUT-GB.ffu Flashing FFU Sending FFU Header CertData Header sent , accepted Perform Data Partition Erase Error : 06 : Data Partition Not Found! Seems as damaged Will Fix partitions by flash whole image Sending FFU Header CertData Header sent , accepted Skip Data Partition Erase Sending FFU Payload Data... Error, stop at : 0x0009 , reason : NO ACK !!! Connection broken due some HW reasons ( like empty battery or cable ) or drivers problem! Red Light Error during flashing! [Info] : Check previous message carefully , follow given advises [Info] : Recommended to not power off device, if it shows "RED SCREEN" [Info] : After problems will be fixed - tick "Recovery" and repeat flashing again! Connect phone on selected interface...

12-29-2016, 14:54	#10 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Read log. Follow it.

03-22-2017, 15:30	#11 (permalink)
trustunlockc Freak Poster Join Date: Nov 2010 Location: Gambia Posts: 309 Member: 1440837 Status: Offline Sonork: 3535 Thanks Meter: 47	Error, stop at : 0x0043 , reason : NO ACK !!!

03-22-2017, 15:30	#12 (permalink)
trustunlockc Freak Poster Join Date: Nov 2010 Location: Gambia Posts: 309 Member: 1440837 Status: Offline Sonork: 3535 Thanks Meter: 47	SECWIM : RM1072_2179.0000.9651.15148.207.725_enosw-wim-signed_825027.secwim Sending WIM ... Error, stop at : 0x0043 , reason : NO ACK !!! Init Error Error during Init TestMode! Connect phone on selected interface...

03-22-2017, 15:53	#13 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Charge battery. Use original short USB cable, direct connection to board with NO hubs.