Nokia N95 8GB (RM-320) UFS Error : 2nd boot not accepted - GSM-Forum

sopla4ever · 04-30-2014, 14:33

Hello, I've got a problem with this phone. Phone can't enter in local/test mode. I can't even read rpl or flash it.

P.S.: LCD and camera already disconnected.

Here is log:

Code:

card found: S/N 3F66:0122
registered to: RescueMe.keed.pl

Connect phone on selected interface...

UFS S/N 80285 boot - Ok

Connect phone on selected interface...

Backup Certificates now...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

APE part info : 
APE ASICID   : 24200705
APE MODE ID : 00
APE PUB ID    : 68AB46D6A9A2916BA29C68FFA9BAF591DE99B16A
APE R_HASH  : BA8710A7E1CD5A2909B9A875DB27AA24

CMT part info : 
CMT ASICID   : 000000010000022600010006400C192101021103
CMT EM0 ID  : 00000295
CMT EM1 ID  : 00000B22
CMT PUB ID  : 18F00119D2670052AE928B88B5363DCF5DD756E1
CMT MODE ID : 00
CMT R_HASH  : CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT ROM ID  : A8C1D6713E691FF8

CMT : Sending 2nd loader...
Use : RAPIDOv11_2nd.fg  ,  Rev : 0.0  Ver : 1.37.1 
Error : 2nd boot not accepted
RX : F372C00B010501242007


Init Service mode... Wait...

Init service mode fail! Can't read flex keys
Connect phone on selected interface...

Dooha_Bd · 04-30-2014, 14:44

Try to flash with ufs hwk & good fbus cabel./

Dzirt · 04-30-2014, 14:50

Hello!
What is phone condition? Due log it not boot APE asic at all. If all disconnected from board - it mean cable (try clean pads and set BSI to 7.1 kOhm) or damage.
Also , in some cases , it have som models, which can't boot correct. Count of them too small and I not found any same to check that.

sopla4ever · 04-30-2014, 18:54

Doesn't start, only white screen. I have only hwk ufs micro, with standard cable pack (without BSI resistance switch). I have not another cable, to exclude this. Shame on me, but I think I'll return it to customer.
Anyway, thanks for your help.

04-30-2014, 14:44	#2 (permalink)
Dooha_Bd No Life Poster Join Date: Nov 2009 Location: Barisal Age: 44 Posts: 1,302 Member: 1427033 Status: Offline Sonork: 100.1596688 Thanks Meter: 1,204	Try to flash with ufs hwk & good fbus cabel./

04-30-2014, 14:50	#3 (permalink)
Dzirt No Life Poster Join Date: Nov 2009 Location: Syberia Age: 34 Posts: 12,508 Member: 1157320 Status: Offline Thanks Meter: 6,192	Hello! What is phone condition? Due log it not boot APE asic at all. If all disconnected from board - it mean cable (try clean pads and set BSI to 7.1 kOhm) or damage. Also , in some cases , it have som models, which can't boot correct. Count of them too small and I not found any same to check that.

04-30-2014, 18:54	#4 (permalink)
sopla4ever Freak Poster Join Date: Aug 2012 Location: LC Posts: 270 Member: 1793281 Status: Offline Thanks Meter: 167	Doesn't start, only white screen. I have only hwk ufs micro, with standard cable pack (without BSI resistance switch). I have not another cable, to exclude this. Shame on me, but I think I'll return it to customer. Anyway, thanks for your help.