Success Test Reports

[A.G.Shahid]

Card found : 30C22462 , v0122
Infinity-Box BEST Nokia [HMD] Module [NK2] v1.20


Operation : Identify [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM7)
MODE : NOKIA USB SERIAL
PORT : 7
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 4B9B9630061D9CFC3DC3A27DB42C63D6
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : NEMO61D.10.00.11.p2
BOOT : SWR : 10.00.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : NEMO61D.10.00.11.p2
FLASH : 00C2 : 0025 : 0036 : 0000
PRDC : 059Z0X8
IMEI[1] : 354189xxxxxxxxx
IMEI[2] : 354189xxxxxxxxx
NCK : 20 digits
PROV : 24407000

Saved as : 354189xxxxxxxxx.mtsec
Saved to : C:\InfinityBox\BEST2\Backup\


Done!
Elapsed: 00:01:11

Reconnect Power/Cable!

Operation : Reset Settings [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM7)
MODE : NOKIA USB SERIAL
PORT : 7
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 4B9B9630061D9CFC3DC3A27DB42C63D6
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : NEMO61D.10.00.11.p2
BOOT : SWR : 10.00.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : NEMO61D.10.00.11.p2
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00C8 : 0060 : 0016 : 0000
NOR: [GigaDevice] GD25LQ32
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00370000 : 0x00088000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:25

Reconnect Power/Cable!

Operation : Read FirmWare [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM7)
MODE : NOKIA USB SERIAL
PORT : 7
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 4B9B9630061D9CFC3DC3A27DB42C63D6
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : NEMO61D.10.00.11.p2
BOOT : SWR : 10.00.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : NEMO61D.10.00.11.p2
FLASH : 00C2 : 0025 : 0036 : 0000
CODE : 0x00370000
Reading Flash ...
TDSN : TA-1114
PRDC : 059Z0X8
PPM : IJ
LANG :
[1] : Urdu (Islamic Republic of Pakistan)
[2] : English (United Kingdom)

BUILD : TA-1114_ROM_eMP_10.00.11
BUILD : TA-1114_LANG_PACK_ROM_IJ_eMP_10.00.11_001
BUILD : TA-1114_CUSTPACK_ROM_IJ_eMP_10.00.11_001
BUILD : TA-1114_JUMP_TABLE_IJ_eMP_10.00.11_001
BUILD : TA-1114_VIVA_eMP_10.00.11

Make VPL definition

Save Path : C:\InfinityBox\BEST2\TA-1114\
Save Name : TA-1114_059Z0X8_10.00.11.vpl

Build Finished!

Done!
Elapsed: 00:06:02

Reconnect Power/Cable!

[Luckey1]

Operation : Reset Settings [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM254)
MODE : NOKIA USB SERIAL
PORT : 254
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 33D3C6928D098C9C4DAA12BC845CD648
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : N103.10.02.11.p1
BOOT : SWR : 10.02.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : N103.10.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00C2 : 0020 : 0016 : 0000
NOR: [MXIC] MX25L3291FWJI_09
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00370000 : 0x00088000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:17

Reconnect Power/Cable!

[Arslanmayo]

Infinity-Box BEST Nokia [HMD] Module [NK2] v1.19


Operation : Reset Settings ( Format FS ) [ v1.19 ]

1. Power off device, remove battery
2. Insert cable, press and hold BootKey ( # )
3. Insert battery in device!

Wait for device ...

Device Connected!
ERROR : Protocol HandShake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Reset Settings ( Format FS ) [ v1.19 ]

Extra : FTM mode
1. Power off device, remove battery
2. Not hold any key on device!
3. Insert battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

Erase BLK #0

Format Ok!

Done!
Elapsed: 00:00:26

Reconnect Power/Cable!

[Luckey1]

Nokia 150 format done

Operation : Reset Settings [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM Port (COM306)
MODE : NOKIA USB SERIAL
PORT : 306
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : A05B11C13ACD1FDEEC65B7314833FFED
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : DUBAI61D.11.00.11.p1
BOOT : SWR : 11.00.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : DUBAI61D.11.00.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00EF : 0070 : 0016 : 0000
NOR: [Winbond] SF_W25Q32JV
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x003A0000 : 0x00058000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:03:46

Reconnect Power/Cable!

[A.G.Shahid]

Card found : 30C22462 , v0122
Infinity-Box BEST Nokia [HMD] Module [NK2] v1.20


Operation : Identify [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM7)
MODE : NOKIA USB SERIAL
PORT : 7
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 84FE7F530E020CF53DA6F720FC718925
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : N103.11.00.11.p1
BOOT : SWR : 11.00.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : N103.11.00.11.p1
FLASH : 00C2 : 0025 : 0036 : 0000
BBSN : 84FE7F530E020CF53DA6F720FC718925
PRDC : 059Z105
IMEI[1] :
IMEI[2] :
NCK : 20 digits
PROV : 24407000

Saved as : xxxxxxxxxxxxxxx.mtsec
Saved to : C:\InfinityBox\BEST2\Backup\


Done!
Elapsed: 00:00:58

Reconnect Power/Cable!

Operation : Reset Settings [ v1.20 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM7)
MODE : NOKIA USB SERIAL
PORT : 7
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 84FE7F530E020CF53DA6F720FC718925
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : N103.11.00.11.p1
BOOT : SWR : 11.00.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : N103.11.00.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00EF : 0070 : 0016 : 0000
NOR: [Winbond] SF_W25Q32JV
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00370000 : 0x00088000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:26

Reconnect Power/Cable!

[gile@gile]

Nokia 3310 3G TA-1022 Flash done
-------------------------
Operation : Identify [ v1.20 ]

1. Power off device, remove battery
2. Insert cable, press and hold BootKey ( # )
3. Insert battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD SECURE BOOT Block version
BootVersion : BEST RETRO3G
Port speed : 921600
FDL Flash : Control transfered!

Boot Done!

SW_VERS : 13.0.0.17.01
PC_EXTR : AX 059Z3N6
IMEI[1] : 357305082247265
IMEI[2] : 352751019523267
BT_ADDR : A92BE328F104
Security saved : NKSPDv2_357305082247265.scnv

Done!
Elapsed: 00:00:25

Reconnect Power/Cable!

File : TA-1022_20.0.0.17.00_AY_059Z525.sprd
SWVersion : 1022_20.0.0.17.00_AY_059Z525
-----------------------
-----------------------
Operation : Write FirmWare [ v1.20 ]

Setting : False : Full Factory Reset
Setting : True : NVRAM Update/Swap

1. Power off device, remove battery
2. Insert cable, press and hold BootKey ( # )
3. Insert battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD SECURE BOOT Block version
BootVersion : BEST RETRO3G
Port speed : 921600
FDL Flash : Control transfered!

Boot Done!

[NVM] : Initialize SRC
[NVM] : Initialize DST
[NVM] : Prepare
[NVM] : SWP : 0x000B : 0x000A
[NVM] : Update
[NVM] : Update Ok!
Flash : KERNELIMG
Flash : BOOTLOADER
Flash : USERIMG
Flash : MMIRES
Flash : DSPCODE
Flash : DSPCODE2
Erase : ERASE AUTOSMS
Erase : ERASE PRELOAD
Flash : PRELOAD
Erase : FLASH

Flashing finished!

Done!
Elapsed: 00:01:20

Reconnect Power/Cable!

[niaz muhammad]

nokia 110 write flash don

Card found: S/N : 8C73AEBC , v0136
Registered to: Niaz muhammad

Connect phone on selected interface...

Core : v2.29 , BB5XG FlashEngine : v10.5

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm827__03.51.mcusw
PPM : rm827__03.51.ppm_mh2
CNT : rm827__03.51.image_mh2_059S4H9
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len  : 0x0A
IF xCPUID    : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data  :  1FB300020303010100FF

Sending EBL Loader ... 
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ... 
EBL sent Ok
EBL : Quantum_Bootloader_10.49_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 356358050339144
IMEI 2 : 356358050339151
PCcode : 059N2R6

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\356358050339144_2nd_XG213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

   ===Flashing [MCU]===
File : rm827__03.51.mcusw
Image : rm827__03.51.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ... 
Erase done, time : 00:00:00 
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ... 
Erase done, time : 00:00:00 
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ... 
Erase done, time : 00:00:05 
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ... 
Erase done, time : 00:01:18 
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:29
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ... 
Erase done, time : 00:00:00 
No write data, skip
CRC check passed , 0xA3D6

   ===Flashing [PPM]===
File : rm827__03.51.ppm_mh2
Image : package_mh2.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ... 
Erase done, time : 00:00:16 
Write , Start : 0x41BC0000 , Len : 0x003664A4
Flashing , wait ...
Region flash done, time : 00:00:04
CRC check passed , 0x8ED2

   ===Flashing [CNT]===
File : rm827__03.51.image_mh2_059S4H9
Image : package_mh2_059S4H9.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ... 
Erase done, time : 00:04:00 
Write , Start : 0x421C0000 , Len : 0x01020000
Flashing , wait ...
Region flash done, time : 00:00:21
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ... 
Erase done, time : 00:00:07 
No write data, skip
CRC check passed , 0x9E52

Flashing done!
Total flash time : 00:06:48
Reboot phone now...

[Luckey1]

Operation : Write FirmWare [ v1.20 ]
Setting : UserData erase : True
Setting : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM342)
MODE : NOKIA USB SERIAL
PORT : 342
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : ED01DA09EA7C238415033F70069E66FE
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : CRYSTAL.10.02.11.p1
BOOT : SWR : 10.02.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : CRYSTAL.10.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

NOR: 00EF : 0040 : 0016 : 0000
NOR: [WINBOND] W25Q32BV
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

VPL SoftwareVersion : 11.00.11 [RM-1035]
DEV SoftwareVersion : 10.02.11
SWInfo compare result : DEVICE SW ( Minor version ) is LOWER, than in VPL!

Load FlashSet :
MROM : RM-1035_ROM_eMP_11.00.11
LANG : RM-1035_LANG_PACK_ROM_IJ_eMP_11.00.11_002
CUST : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.00.11_002
JUMP : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_11.00.11_002
VIVA : RM-1035_VIVA_eMP_11.00.11

Prepare FlashSet :
DCR : RM-1035_ROM_eMP_11.00.11
DCR : RM-1035_LANG_PACK_ROM_IJ_eMP_11.00.11_002
DCR : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.00.11_002
DCR : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_11.00.11_002
DCR : RM-1035_VIVA_eMP_11.00.11

Prepare Target
SDS : OK : 0x003F4000 : 0x0000C000
FFS Format Ok!
CBR : 0x0000001A:0x00000001:0x00000000:0x00000000:0x0000 0010:0x00000002:0x00000000

Erase Target Flash
Erase done!

Write Target Flash
Write : RM-1035_ROM_eMP_11.00.11
Write : RM-1035_LANG_PACK_ROM_IJ_eMP_11.00.11_002
Write : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.00.11_002
Write : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_11.00.11_002
Write : RM-1035_VIVA_eMP_11.00.11
Write done, waiting target response ...
Write flash done!

Verify Target FlashContent
Verify : RM-1035_ROM_eMP_11.00.11
Verify : RM-1035_LANG_PACK_ROM_IJ_eMP_11.00.11_002
Verify : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.00.11_002
Verify : _JUMP_TABLE_IJ_MEA_PK_eMP_11.00.11_002
Verify : RM-1035_VIVA_eMP_11.00.11

Done!
Elapsed: 00:01:21

Reconnect Power/Cable!

[tapas770]

Phone Problem Was Hang Logo,


Solved By Best Dongle

Infinity-Box BEST Nokia [HMD] Module [NK2] v1.19


Load : C:\Users\AhnafTelecom\Desktop\HMDSW_Wasp-1280-0-00WW-B01.zip
Device : wasp
Android: 9
SKU ID : 600WW
ROM Ver: PPR1.180610.011
Load Ok!

Operation : Flash Firmware [FTM] [ v1.19 ]
Setting : UserData preserve : False
Setting : FRP Reset : True
Setting : Change SKUID : False
Setting : Keep SVC : True

-> Old : Power Off Phone, wait 5-10 seconds, Insert USB cable
-> New : Power Off Phone, press and hold VOL_DOWN and POWER keys, until FASTBOOT screen appear

Wait for phone...
Connect Ok!
Device Found!
Initialize ...
Initialize Ok!

Dev Model : Wasp
HW version : 1.0
HW variant : MTK EMMC
HW RF_BAND : G_850_900_1800_1900^W_1_5_8^L_1_3_5_7_8
SW version : WSP_sprout-163A-0-00WW-B01
SW CurrSlot : A
SW serialnm : HZAL1620C7J7A901740
SW secured : YES
Bootloader type : WT2
Security Version : 0002

Prepare base package, please, wait ...
Prepare data package, please, wait ...
Prepare update package, please, wait ...


Device : Wasp ( Wasp )
BLType : WT2
SecVer : 02
Device authentification ...
Processing server operation ...
Connecting to server...
Connected
Authenticating...
Authenticated
Checking Client version...
Client version is valid
Process...
Finished
Disconnected
Finished
Challenge : Process
Challenge : Passed!

OP : Initial

Process : preloader_a : preloader_wasp.bin
Process : custom_a : custom.img
SPImage : Process custom_a_0
Process : custom_b : custom.img
SPImage : Process custom_b_0
Process : logo : logo.bin
Process : lk_a : lk.img
Process : dtbo_a : dtbo.img
Process : md1img_a : md1img.img
Process : scp_a : scp.img
Process : spmfw_a : spmfw.img
Process : sspm_a : sspm.img
Process : tee_a : tee.img
Process : system_b : system_other.img
SPImage : Process system_b_0
SPImage : Process system_b_1
SPImage : Process system_b_2

OP : Update

Process : boot_a : boot_a.img
Process : elabel_a : elabel_a.img
SPImage : Process elabel_a_0
Process : system_a : system_a.img
SPImage : Process system_a_0
SPImage : Process system_a_1
SPImage : Process system_a_2
SPImage : Process system_a_3
SPImage : Process system_a_4
SPImage : Process system_a_5
SPImage : Process system_a_6
SPImage : Process system_a_7
SPImage : Process system_a_8
SPImage : Process system_a_9
SPImage : Process system_a_10
SPImage : Process system_a_11
SPImage : Process system_a_12
SPImage : Process system_a_13
SPImage : Process system_a_14
SPImage : Process system_a_15
SPImage : Process system_a_16
SPImage : Process system_a_17
Process : userdata : userdata.img
SPImage : Process userdata_0
Process : vbmeta_a : vbmeta_a.img
Process : vendor_a : vendor_a.img
SPImage : Process vendor_a_0
SPImage : Process vendor_a_1
SPImage : Process vendor_a_2

OP : Post


OP : UserData preserve : disabled
Process : userdata : userdata.img
SPImage : Process userdata_0

OP : Reset FRP

Device : Wasp ( Wasp )
BLType : WT2
SecVer : 02
Device authentification ...
Processing server operation ...
Connecting to server...
Connected
Authenticating...
Authenticated
Checking Client version...
Client version is valid
Process...
Finished
Disconnected
Finished
Challenge : Process
Challenge : Passed!

Reset FRP Ok!

Done!
Elapsed: 00:13:43

Reconnect Power/Cable!

Thanks Infinity Team such A Strong Update..

[Nadeem Waris]

Operation : Reset Settings [ v1.19 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM4)
MODE : NOKIA USB SERIAL
PORT : 4
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : BBAD70AC092DB834DC07337B21E458B0
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
BOOT : SWR : 11.02.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : RETRO.11.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

NOR: 00EF : 0060 : 0018 : 0000
NOR: [WINBOND] W25Q128FW
NOR:
TSIZE : 0x01000000 [ 16.00 MB ]
PSIZE : 0x01000000 [ 16.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00CD0000 : 0x00324000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:01:08

Reconnect Power/Cable!

[Nadeem Waris]

Infinity-Box BEST Nokia [HMD] Module [NK2] v1.19


Operation : Reset Settings [ v1.19 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM4)
MODE : NOKIA USB SERIAL
PORT : 4
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C889804EBEC668C9E229E3E6DA3ED6F1
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : N103.30.04.11.p1
BOOT : SWR : 30.04.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : N103.30.04.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00EF : 0070 : 0016 : 0000
NOR: [Winbond] SF_W25Q32JV
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00370000 : 0x00088000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:31

[Nadeem Waris]

Operation : Reset Settings [ v1.19 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM59)
MODE : NOKIA USB SERIAL
PORT : 59
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 4F7661552F21D15625B0B759218D07CE
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : KESA61A.10.00.11.p2
BOOT : SWR : 10.00.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : KESA61A.10.00.11.p2
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00EF : 0060 : 0017 : 0000
NOR: [WINBOND] W25Q64DW
NOR:
TSIZE : 0x00800000 [ 8.00 MB ]
PSIZE : 0x00800000 [ 8.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00580000 : 0x00278000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:29

Reconnect Power/Cable!

[Nadeem Waris]

Operation : Write FirmWare [ v1.19 ]
Setting : UserData erase : True
Setting : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM4)
MODE : NOKIA USB SERIAL
PORT : 4
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 9C9515A64E9A7890E6F8C7671465BB60
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : KESA61A.10.00.11.p2
BOOT : SWR : 10.00.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : KESA61A.10.00.11.p2
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00EF : 0060 : 0017 : 0000
NOR: [WINBOND] W25Q64DW
NOR:
TSIZE : 0x00800000 [ 8.00 MB ]
PSIZE : 0x00800000 [ 8.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

VPL SoftwareVersion : 11.02.11 [TA-1017]
DEV SoftwareVersion : 10.00.11
SWInfo compare result : DEVICE SW ( Minor version ) is LOWER, than in VPL!

Load FlashSet :
MROM : TA-1017_ROM_eMP_11.02.11
LANG : TA-1017_LANG_PACK_ROM_IJ_eMP_11.02.11_001
CUST : TA-1017_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.02.11_001
JUMP : TA-1017_JUMP_TABLE_IJ_MEA_PK_eMP_11.02.11_001
VIVA : TA-1017_VIVA_eMP_11.02.11

Prepare FlashSet :
DCR : TA-1017_ROM_eMP_11.02.11
DCR : TA-1017_LANG_PACK_ROM_IJ_eMP_11.02.11_001
DCR : TA-1017_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.02.11_001
DCR : TA-1017_JUMP_TABLE_IJ_MEA_PK_eMP_11.02.11_001
DCR : TA-1017_VIVA_eMP_11.02.11

Prepare Target
SDS : OK : 0x007F8000 : 0x00008000
FFS Format Ok!

Erase Target Flash
Erase done!

Write Target Flash
Write : TA-1017_ROM_eMP_11.02.11
Write : TA-1017_LANG_PACK_ROM_IJ_eMP_11.02.11_001
Write : TA-1017_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.02.11_001
Write : TA-1017_JUMP_TABLE_IJ_MEA_PK_eMP_11.02.11_001
Write : TA-1017_VIVA_eMP_11.02.11
Write done, waiting target response ...
Write flash done!

Verify Target FlashContent
Verify : TA-1017_ROM_eMP_11.02.11
Verify : TA-1017_LANG_PACK_ROM_IJ_eMP_11.02.11_001
Verify : TA-1017_CUSTPACK_ROM_IJ_MEA_PK_eMP_11.02.11_001
Verify : TA-1017_JUMP_TABLE_IJ_MEA_PK_eMP_11.02.11_001
Verify : TA-1017_VIVA_eMP_11.02.11

Done!
Elapsed: 00:01:32

Reconnect Power/Cable!

[Nadeem Waris]

Operation : Reset Settings [ v1.19 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM4)
MODE : NOKIA USB SERIAL
PORT : 4
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : FC829D90113FCDBDAA99D64A0A101FFF
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
BOOT : SWR : 11.02.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : RETRO.11.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

NOR: 00C2 : 0025 : 0038 : 0000
NOR: [MXIC] MX25U12835FZNI_10G
NOR:
TSIZE : 0x01000000 [ 16.00 MB ]
PSIZE : 0x01000000 [ 16.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00CD0000 : 0x00324000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:46

[Nadeem Waris]

Operation : Reset Settings [ v1.19 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM13)
MODE : NOKIA USB SERIAL
PORT : 13
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCA02 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 209E2544E7EC7FB4BB65CD1914C9E025
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : KESA61A.10.00.11.p2
BOOT : SWR : 10.00.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : KESA61A.10.00.11.p2
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8E

NOR: 00EF : 0060 : 0017 : 0000
NOR: [WINBOND] W25Q64DW
NOR:
TSIZE : 0x00800000 [ 8.00 MB ]
PSIZE : 0x00800000 [ 8.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00580000 : 0x00278000
FFS Format ...
FFS Format Ok!

Done!
Elapsed: 00:00:25