HTC Desire C (PL01100) - GSM-Forum

simo_scorpion · 07-06-2013, 16:29

HTC Desire C (PL01100) - added Unlock (via Read Codes), Repair CID, Repair IMEI,

i have phone working need change CID

no detect the phone

Welcome to Medusa Box Software version 1.8.8
Selected device model: HTC Desire C (PL01100)
Connecting. Please wait...
VREF = 0.0V is less than required level. Please check target device power supply.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list:
0x000000C1
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000007
0x00000000
MI: Medusa JTAG init failed.

Octopus box · 07-08-2013, 06:16

Hello.
Most likely, You soldered some Jtag wires incorrectly. Please check soldering of all Jtag wires and try again. Don't forget to fully charge phone's battery. To power your device use fully charged battery and USB cable. We have tried with our device and Connect was successfully:

Quote:

Selected device model: HTC Desire C (PL01100)
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 106010E1, IR Length = 4.
JTAG speed : Auto (RTCK).
VREF level : 1.79 V
CPU : Qualcomm MSM7225A
Core ID : 106010E1
Storage Device: Samsung eMMC SJS00A
Device ID : 00150001
Block size : 512 bytes
Blocks : 4751360
Storage size : 2320 Mb
Connect successful.

osom · 08-06-2013, 22:22

mr supporter

can u add phone jtag picture
ı have desire c but not connect cpu
Can u help me please

clone · 08-15-2013, 09:36

I have the same problem ...

I would like to "repair imei" on a working phone , but can't connect to the board .. Yes,i checked the soldered wires - i tried two different wires -as you can see in the pictures in my comment.(that you couldn't see : the reset wire is soldered too on the backside) Yes, the battery is fully charged,and i use charger or usb wire too.

By RTCK selection - the result is the same,like the first poster(expect the VREF -it is 1.75V)
By 100kHz manual mode the result is the following :

Selected device model: HTC Desire C (PL01100)
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 106010E1, IR Length = 4.
JTAG speed : 100 KHz.
VREF level : 1.75 V
CPU : Qualcomm MSM7225A
Core ID : 106010E1
ERROR[004]: Medusa Device Server did not replied to HELLO command.

Could you suggest me any other thing ,that i have never tried ?

http://forum.gsmhosting.com/vbb/atta...1&d=1376555543

Octopus box · 08-15-2013, 11:09

Hello.
Please try to connect your phone in Auto Mode (select "Manufacturer: Auto", "Device model: MSM72xx/MSM76xx", "JTAG speed: Auto (RTCK)") and post here log.

Also please use both - fully charged battery and USB cable at the same time for powering the device.

clone · 08-15-2013, 11:18

Unfortunately it is the same situation .. And of course i try it with usb and battery power at the same time. It isn't my first jtag "project"

http://forum.gsmhosting.com/vbb/atta...1&d=1376561833

In RTCK mode :

Selected device model: Qualcomm MSM72xx/MSM76xx
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
MI: Medusa JTAG init failed.

In : 100 kHz manual mode :

Octopus box · 08-16-2013, 10:10

Also please try to connect the phone by the next way:
1. Disconnect phone's battery, mictro USB cable and Jtag wires.
2. Connect soldered Jtag wires to Box and press "Connect" button in Software.
3. Connect fully charged battery and press "Power On" button.
4. If the phone not connects, You can (should) try to connect it a few times by the same way.

Currently we have no this device in our hands, so we cant check whether can be the problem with your device exactly. We have tested now on HTC Explorer (with the same CPU) and the mentioned above connectin procedure works OK.

clone · 08-16-2013, 10:25

I have done all steps but the result is exactly the same

Not the first phone,that i couldn't done with the medusa - tomorrow i'll make one more try with an other PC , but today i have no more time for it .

richiricherd · 11-09-2013, 02:12

Im facing exactly same situation with same phone

Octopus box · 11-09-2013, 09:04

Hello.
Please post here full software log and describe all of your actions step by step how You connect the device.

richiricherd · 11-10-2013, 03:06

Quote:

Originally Posted by Octopus box

Hello.
Please post here full software log and describe all of your actions step by step how You connect the device.

Ok Sir, Ive check very well solder points and all are ok but I have same problem, cant conect the phone.. Here is log:

Selected device model: Auto
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S256 revision C.
Detected TAP ID: 106010E1, IR Length = 4.
JTAG speed : 100 KHz.
VREF level : 1.74 V
CPU : Qualcomm MSM7225A
Core ID : 106010E1
ERROR[004]: Medusa Device Server did not replied to HELLO command.
Selected device model: Auto
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S256 revision C.
ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list:
0x000010E1
0x00000000
0x00000000
0x00000000
0x0000001F
0x00000000
0x0000000F
0x0000000F
MI: Medusa JTAG init failed.

Ive tried HTC Decire C model and Auto model and same result, Ive tried diferent Jtag speed and only with 100 Khz I get this:

Selected device model: Auto
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S256 revision C.
Detected TAP ID: 106010E1, IR Length = 4.
JTAG speed : 100 KHz.
VREF level : 1.74 V
CPU : Qualcomm MSM7225A
Core ID : 106010E1
ERROR[004]: Medusa Device Server did not replied to HELLO command.

But if I select directly CPU type Qualcom MSM72xx/MSM76xx and 100 Khz speed I get this:

Selected device model: Qualcomm MSM72xx/MSM76xx
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S256 revision C.
Detected TAP ID: 106010E1, IR Length = 4.
JTAG speed : 100 KHz.
VREF level : 1.74 V
CPU : Qualcomm MSM7225A
Core ID : 106010E1
Storage Device: Hynix eMMC XINYH
Device ID : 00904A01
Block size : 512 bytes
Blocks : 4702208
Storage size : 2296 Mb
Connect successful.

But there are not options for repair IMEI Sir.. What can I do next??

Octopus box · 11-10-2013, 08:16

Hello.
To make Repair IMEI, You need to connect the device as HTC Desire C (PL01100).

Don't forget to fully charge phone's battery. To power your device use fully charged battery and USB cable.

To connect the device try to do the next steps:
1. Disconnect phone's battery, mictro USB cable and Jtag wires.
2. Connect soldered Jtag wires to Box and press "Connect" button in Software.
3. Connect fully charged battery and press "Power On" button.
4. If the phone not connects, You can (should) try to connect it a few times by the same way.

richiricherd · 11-13-2013, 21:31

Ok Sir I think that I found the problem, and Im sorry cause my mistake, this phone is HTC Desire C ( PL01130 ) not ( PL01100 ) as you support that Desire C only..

Im very ashame sir..

richiricherd · 01-17-2014, 19:41

Sir please add support for Desire C PL01130, I think is equal than PL01100 but your software refuses it because not exactly same number but same hardware.. Only diference in hardware is 3G Bands frecuency..

Roman Tovar · 11-30-2014, 16:01

Quote:

Originally Posted by richiricherd

Sir please add support for Desire C PL01130, I think is equal than PL01100 but your software refuses it because not exactly same number but same hardware.. Only diference in hardware is 3G Bands frecuency..

A doubt desiree htc PL01130, I selected the model of octoplus jtag PL01100 to repair imei?

Una duda, el htc desiree PL01130, debo de seleccionar el modelo en jtag de octoplus PL01100 para poder reparar el imei?

07-06-2013, 16:29	#1 (permalink)
simo_scorpion Freak Poster Join Date: Mar 2004 Location: Austria Age: 45 Posts: 285 Member: 57712 Status: Offline Sonork: 1010 Thanks Meter: 49	HTC Desire C (PL01100) HTC Desire C (PL01100) - added Unlock (via Read Codes), Repair CID, Repair IMEI, i have phone working need change CID no detect the phone Welcome to Medusa Box Software version 1.8.8 Selected device model: HTC Desire C (PL01100) Connecting. Please wait... VREF = 0.0V is less than required level. Please check target device power supply. Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision C. ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list: 0x000000C1 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000007 0x00000000 MI: Medusa JTAG init failed.

08-06-2013, 22:22	#3 (permalink)
osom No Life Poster Join Date: May 2005 Location: Türkiye Age: 42 Posts: 569 Member: 145175 Status: Offline Thanks Meter: 22	mr supporter can u add phone jtag picture ı have desire c but not connect cpu Can u help me please

08-15-2013, 11:09	#5 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,847 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,412	Hello. Please try to connect your phone in Auto Mode (select "Manufacturer: Auto", "Device model: MSM72xx/MSM76xx", "JTAG speed: Auto (RTCK)") and post here log. Also please use both - fully charged battery and USB cable at the same time for powering the device.

08-16-2013, 10:10	#7 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,847 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,412	Also please try to connect the phone by the next way: 1. Disconnect phone's battery, mictro USB cable and Jtag wires. 2. Connect soldered Jtag wires to Box and press "Connect" button in Software. 3. Connect fully charged battery and press "Power On" button. 4. If the phone not connects, You can (should) try to connect it a few times by the same way. Currently we have no this device in our hands, so we cant check whether can be the problem with your device exactly. We have tested now on HTC Explorer (with the same CPU) and the mentioned above connectin procedure works OK.

08-16-2013, 10:25	#8 (permalink)
clone Freak Poster Join Date: Dec 2002 Location: Hungary, near Miskolc Age: 48 Posts: 407 Member: 19327 Status: Offline Thanks Meter: 45	I have done all steps but the result is exactly the same Not the first phone,that i couldn't done with the medusa - tomorrow i'll make one more try with an other PC , but today i have no more time for it .

11-09-2013, 02:12	#9 (permalink)
richiricherd No Life Poster Join Date: Sep 2007 Location: Venezuela Posts: 846 Member: 594580 Status: Offline Thanks Meter: 157	Im facing exactly same situation with same phone

11-09-2013, 09:04	#10 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,847 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,412	Hello. Please post here full software log and describe all of your actions step by step how You connect the device.

11-10-2013, 08:16	#12 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,847 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,412	Hello. To make Repair IMEI, You need to connect the device as HTC Desire C (PL01100). Don't forget to fully charge phone's battery. To power your device use fully charged battery and USB cable. To connect the device try to do the next steps: 1. Disconnect phone's battery, mictro USB cable and Jtag wires. 2. Connect soldered Jtag wires to Box and press "Connect" button in Software. 3. Connect fully charged battery and press "Power On" button. 4. If the phone not connects, You can (should) try to connect it a few times by the same way.

11-13-2013, 21:31	#13 (permalink)
richiricherd No Life Poster Join Date: Sep 2007 Location: Venezuela Posts: 846 Member: 594580 Status: Offline Thanks Meter: 157	Ok Sir I think that I found the problem, and Im sorry cause my mistake, this phone is HTC Desire C ( PL01130 ) not ( PL01100 ) as you support that Desire C only.. Im very ashame sir..

01-17-2014, 19:41	#14 (permalink)
richiricherd No Life Poster Join Date: Sep 2007 Location: Venezuela Posts: 846 Member: 594580 Status: Offline Thanks Meter: 157	Sir please add support for Desire C PL01130, I think is equal than PL01100 but your software refuses it because not exactly same number but same hardware.. Only diference in hardware is 3G Bands frecuency..