Motorola XT615 boot repair

[mahcin]

Hi,
I made boot repair on XT615 - fully DEAD
repair successfull, after repair PC started recognizing phone as a ZEUS Flash Device,
before repairing wasn't recognizing at all.
Phone is not turning on, after connecting to PC is recognized as a ZEUS flash device, is this HW problem of motherboard? or still SW? Why is not turning on? Strange one, please help

[mahcin]

here is my log, which looks fine, I think:

Log started at 2014-05-12 10:55:13 ...
Welcome to Medusa Box Software version 2.2.3
Connecting to server
Retrieving files list
Connecting to server
Retrieving files list
Operating Mode: EasyRepair Mode
Selected device model: Motorola XT615
Connecting. Please wait...
VREF = 0.0V is less than required level. Please check target device power supply.
ERROR[035]: Target device has been powered off during connect.
Please connect the target device and power it on...
VREF = 0.0V is less than required level. Please check target device power supply.
MI: RTCK reaction time 126 ns, average speed 7936 KHz.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision B.
Detected TAP ID: 106200E1, IR Length = 4.
MI: Halting target, attempt 1.
JTAG speed  : Auto (RTCK).
VREF level  : 1.74 V
CPU         : Qualcomm MSM7227A
Core ID     : 106200E1
MI: Loading Medusa Device Server V1.2.
MI: Starting...
MI: Received status 0xFFFFFFFF, cycle 0.
MI: Received status 0x0000F00F, cycle 1.
MI: Received server capabilities 0x00000037.
MI: Detailed server caps: FLASH, CFG, ECC, WDOG, DWP
MI: Watchdog configuration: 0xB800010C, 0x00000001... ok
MI: Server init.
MI: Received flash ID 0xA02C55B3.
MI: Flash geometry set.
MI: Recheking settings... ok
Server caps : 00000037
Flash device: Micron 1024Mb
Flash ID    : 002C55B3
 Page size  : 2048 bytes
 Block size : 64 pages (128 Kb)
 Block count: 8192
 Flash size : 1024 Mb
MI: Setting configuration: 0xAAD400DA, 0x0044747E, 0x0000000D
MI: Configuration done.
Opening "C:\Users\NC10\Desktop\MOTOROLA_XT615_Repair\MOTOROLA_XT615_Repair.mf" file...
Writing BOOT section. Please wait... Done
Disconnected

[Octopus box]

Hello.

repair successfull, after repair PC started recognizing phone as a ZEUS Flash Device,

Try to re-install proper Motorola drivers and re-flash the device by using Motorola tool, that supports this device model.

[mahcin]

Originally Posted by Octopus box

Hello.


Try to re-install proper Motorola drivers and re-flash the device by using Motorola tool, that supports this device model.

Thank You for answer,
unfortunately nothing wrong with drivers, I have got another XT615 - working one, which has no problem with flashing/drivers/motorola tool, etc

so I see two ways: HW problem, or maybe different repair flash file needed? Different version? This is very strange, because Medusa flashed it successfully and recognized, just why after I cannot do nothing with this one unit?

Motorola tool is recognizing my other working XT615, but this one is not recognizing

[MVNDOzone]

if phone detected as ZEUZ flash is detected as Qualcomm 9008

try update driver and chose another driver

[iusalmprim]

File from support X615- is ok. After him my phone is power on.