n7000 Samsung Galaxy Note JTAG Brick Repair - GSM-Forum

yargich · 07-09-2012, 07:53

use 1.48
use 1.49
use 1.5.0.1
all version exe but same error
easy mode repair
1.0 MHZ
how to repair step by step
Samsung Galaxy Note JTAG Brick Repair
Welcome to Medusa Box Software version 1.4.9
Selected device model: Samsung GT-N7000
Connecting. Please wait...
VREF = 0.0V is less than required level. Please check target device power supply.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 4BA00477, IR Length = 4.
JTAG speed : 1000 KHz.
VREF level : 2.75 V
CPU : Samsung S5PC210
Core ID : 4BA00477
Storage Device: Samsung eMMC VYL00M
Device ID : 00150001
Block size : 512 bytes
Blocks : 30777344
Storage size : 14.7 Gb
Opening "D:\gsm\box supportlari\medusa\firmware\SAMSUNG_GTN7000_Repair .mf" file...
Writting BOOT section. Please wait...
ERROR[018]: Logical block operation failed at 16 Kb (Hex address 0x00004000). Reason: Connection lost.

Medusa Box · 07-09-2012, 08:00

Hello.
Please try to connect your device in Auto Mode - select "Manufacturer: Auto" and "Device model: Samsung S5PC210". Try to Read Boot in this mode.

yargich · 07-09-2012, 08:07

Selected device model: Samsung S5PC210
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
ERROR[031]: TDO is constant low. Please check target device connection.
MI: Medusa JTAG init failed.

yargich · 07-09-2012, 08:09

Selected device model: Samsung S5PC210
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list:
0x4BA00477
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
MI: Medusa JTAG init failed.

yargich · 07-09-2012, 08:10

Selected device model: Samsung S5PC210
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list:
0x00000007
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
MI: Medusa JTAG init failed.

Medusa Box · 07-09-2012, 08:54

Have You soldered Reset wires?

yargich · 07-09-2012, 11:12

Quote:

Originally Posted by Medusa Box

Have You soldered Reset wires?

same problem again.............

yargich · 07-10-2012, 07:42

yes remove all
solder one by one
Samsung Galaxy Note JTAG Brick Repair
Welcome to Medusa Box Software version 1.4.9
Selected device model: Samsung GT-N7000
Connecting. Please wait...
VREF = 0.0V is less than required level. Please check target device power supply.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 4BA00477, IR Length = 4.
JTAG speed : 1000 KHz.
VREF level : 2.75 V
CPU : Samsung S5PC210
Core ID : 4BA00477
Storage Device: Samsung eMMC VYL00M
Device ID : 00150001
Block size : 512 bytes
Blocks : 30777344
Storage size : 14.7 Gb
Opening "D:\gsm\box supportlari\medusa\firmware\SAMSUNG_GTN7000_Repair .mf" file...
Writting BOOT section. Please wait...
ERROR[018]: Logical block operation failed at 16 Kb (Hex address 0x00004000). Reason: Connection lost
how is the fixed

Medusa Box · 07-10-2012, 07:54

Most likely, the problem is with flash chip of your phone.

yargich · 07-10-2012, 07:57

how to repair.
buy new flash chip
Storage Device: Samsung eMMC VYL00M

Medusa Box · 07-16-2012, 05:53

Try to re-place phone's flash chip and make Repair again.

GTunlocker · 10-28-2012, 04:54

Quote:

Originally Posted by Medusa Box

Try to re-place phone's flash chip and make Repair again.

hi
me too have same the problem with N7000 note
i am use riff ... why canot repair it

Medusa Box · 10-28-2012, 09:11

@ GTunlocker

What do You mean under "same the problem with N7000 note"? What is the state of your device? Also please post here full software log with the Repair procedure.

07-09-2012, 07:53	#1 (permalink)
yargich Freak Poster Join Date: May 2003 Location: King of Nokia Age: 36 Posts: 479 Member: 28531 Status: Offline Thanks: 76 Thanked 66 Times in 38 Posts	n7000 Samsung Galaxy Note JTAG Brick Repair use 1.48 use 1.49 use 1.5.0.1 all version exe but same error easy mode repair 1.0 MHZ how to repair step by step Samsung Galaxy Note JTAG Brick Repair Welcome to Medusa Box Software version 1.4.9 Selected device model: Samsung GT-N7000 Connecting. Please wait... VREF = 0.0V is less than required level. Please check target device power supply. Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision C. Detected TAP ID: 4BA00477, IR Length = 4. JTAG speed : 1000 KHz. VREF level : 2.75 V CPU : Samsung S5PC210 Core ID : 4BA00477 Storage Device: Samsung eMMC VYL00M Device ID : 00150001 Block size : 512 bytes Blocks : 30777344 Storage size : 14.7 Gb Opening "D:\gsm\box supportlari\medusa\firmware\SAMSUNG_GTN7000_Repair .mf" file... Writting BOOT section. Please wait... ERROR[018]: Logical block operation failed at 16 Kb (Hex address 0x00004000). Reason: Connection lost.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
How can I do a Welcome note for my 6110 a dosn't have any one ?	Viper	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	7	07-18-2012 07:57
Nokia "Contact Service" Repairer	Dirk	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	5	10-04-2011 05:45
Repaired dead phone without backup	Prodigal	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	3	07-29-2011 11:26
Contact Service Repairer 1.2 by Bartek	Allen	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	4	02-23-2011 08:00
New!! Nokia Flash Checksum And Contact Service Repair	HookerGsM	Main Sales Section	0	01-02-2001 09:12

07-09-2012, 08:00	#2 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 2,168 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks: 880 Thanked 721 Times in 474 Posts	Hello. Please try to connect your device in Auto Mode - select "Manufacturer: Auto" and "Device model: Samsung S5PC210". Try to Read Boot in this mode.

07-09-2012, 08:07	#3 (permalink)
yargich Freak Poster Join Date: May 2003 Location: King of Nokia Age: 36 Posts: 479 Member: 28531 Status: Offline Thanks: 76 Thanked 66 Times in 38 Posts	Selected device model: Samsung S5PC210 Connecting. Please wait... Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision C. ERROR[031]: TDO is constant low. Please check target device connection. MI: Medusa JTAG init failed.

07-09-2012, 08:09	#4 (permalink)
yargich Freak Poster Join Date: May 2003 Location: King of Nokia Age: 36 Posts: 479 Member: 28531 Status: Offline Thanks: 76 Thanked 66 Times in 38 Posts	Selected device model: Samsung S5PC210 Connecting. Please wait... Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision C. ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list: 0x4BA00477 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF MI: Medusa JTAG init failed.

07-09-2012, 08:10	#5 (permalink)
yargich Freak Poster Join Date: May 2003 Location: King of Nokia Age: 36 Posts: 479 Member: 28531 Status: Offline Thanks: 76 Thanked 66 Times in 38 Posts	Selected device model: Samsung S5PC210 Connecting. Please wait... Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision C. ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list: 0x00000007 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 MI: Medusa JTAG init failed.

07-09-2012, 08:54	#6 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 2,168 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks: 880 Thanked 721 Times in 474 Posts	Have You soldered Reset wires?

07-10-2012, 07:42	#8 (permalink)
yargich Freak Poster Join Date: May 2003 Location: King of Nokia Age: 36 Posts: 479 Member: 28531 Status: Offline Thanks: 76 Thanked 66 Times in 38 Posts	yes remove all solder one by one Samsung Galaxy Note JTAG Brick Repair Welcome to Medusa Box Software version 1.4.9 Selected device model: Samsung GT-N7000 Connecting. Please wait... VREF = 0.0V is less than required level. Please check target device power supply. Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision C. Detected TAP ID: 4BA00477, IR Length = 4. JTAG speed : 1000 KHz. VREF level : 2.75 V CPU : Samsung S5PC210 Core ID : 4BA00477 Storage Device: Samsung eMMC VYL00M Device ID : 00150001 Block size : 512 bytes Blocks : 30777344 Storage size : 14.7 Gb Opening "D:\gsm\box supportlari\medusa\firmware\SAMSUNG_GTN7000_Repair .mf" file... Writting BOOT section. Please wait... ERROR[018]: Logical block operation failed at 16 Kb (Hex address 0x00004000). Reason: Connection lost how is the fixed

07-10-2012, 07:54	#9 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 2,168 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks: 880 Thanked 721 Times in 474 Posts	Most likely, the problem is with flash chip of your phone.

07-10-2012, 07:57	#10 (permalink)
yargich Freak Poster Join Date: May 2003 Location: King of Nokia Age: 36 Posts: 479 Member: 28531 Status: Offline Thanks: 76 Thanked 66 Times in 38 Posts	how to repair. buy new flash chip Storage Device: Samsung eMMC VYL00M

07-16-2012, 05:53	#11 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 2,168 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks: 880 Thanked 721 Times in 474 Posts	Try to re-place phone's flash chip and make Repair again.

10-28-2012, 09:11	#13 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 2,168 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks: 880 Thanked 721 Times in 474 Posts	@ GTunlocker What do You mean under "same the problem with N7000 note"? What is the state of your device? Also please post here full software log with the Repair procedure.