i9070 and i9070p some ??? - GSM-Forum

roklat · 01-22-2013, 07:18

i need more info

i9070p repaired by ort jtag done but the phone always dead

Recommended Procedure :
Connect JTAG Pinouts
Connect USB Cable to phone
Install USB Drivers "\drivers\STERICSSON_U8500"
Click Repair
Samsung GT-I9070
U8500 1.8V
U8500 USB is ready!
arm.tap,pos:0,IRLength:4,DeviceID:0x62286041
CPUID=0x62286041
U8500
IOLevel:1.8V
FlashID:0x454D303845010053,SubFlashID:0x8F762F7647 9071AE
BlockSize:512
PageSize:512

Actual Density:0x1D2000000
Writing Boot...
100%
Boot restored.
.....................................

U8500 USB is ready!
Vref:1.834V
TCK:05MHz
Model:U8500_eMMC
arm.tap,pos:0,IRLength:4,DeviceID:0x62286041.
FlashID:0x454D303845010053,SubFlashID:0x8F762F7647 9071AE
BlockSize:512
PageSize:512
Density:8192MB
Actual Density:0x1D2000000
FlashName:SEM08G

dimension_minaz · 01-27-2013, 17:21

U8500 USB is not ready.
U8500 USB is not ready.
U8500 USB is ready!
Vref:1.834V
TCK:05MHz
Model:U8500_eMMC
arm.tap,pos:0,IRLength:4,DeviceID:0x62286041.
FlashID:0x454D303845010053,SubFlashID:0x3DAB9F5047 90B1C8
BlockSize:512
PageSize:512
Density:8192MB
Actual Density:0x1D2000000
FlashName:SEM08G
What is next step...?

sp-lox · 01-29-2013, 17:37

What i not correctly do ???

Run ORT V1.89
select Samsung GT-I9070
click Scan

log:
U8500 USB is not ready.
U8500 USB is not ready.
U8500 USB is not ready.
U8500 USB is not ready.
U8500 USB is ready!
Vref:1.834V
TCK:05MHz
Model:GT-I9070
arm.tap,pos:0,IRLength:4,DeviceID:0x62286041.
FlashID:0x454D303845010053,SubFlashID:0x7284AFFC47 904055
BlockSize:512
PageSize:512
Density:8192MB
Actual Density:0x1D2000000
FlashName:SEM08G

Run EasyMode
Select Samsung GT-I9070

log:
Samsung GT-I9070
U8500 1.8V
arm.tap,pos:0,IRLength:4,DeviceID:0x62286041
Scan CPU failed(-107)

dimension_minaz · 01-30-2013, 16:46

ORT Team Plz guide us

Tricom · 01-30-2013, 17:35

These 2 models are different even i9070 with different emmc size is dfferenr hardwares

So "P" is not yet supported

Best regards

vistaunlock · 03-15-2013, 21:17

PLZ help i update phone i9070p with HOME_I9070XXLQ4_I9070SERLQ4_660490_REV00_user_low_ ship.tar.md5
now phone is dead no boot even with JIC usb . trying JTAG and result :

VREF = 0.0V is less than required level. Please check target device power supply.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision B.
ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list:
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
MI: Medusa JTAG init failed.

Normandy

vistaunlock · 03-15-2013, 21:26

Done , bad connection it was
Connect successful.
Disconnected
Selected device model: Samsung GT-I9070
Connecting. Please wait...
Resetting target. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision B.
Detected TAP ID: 62286041, IR Length = 6.
JTAG speed : 2400 KHz.
VREF level : 1.77 V
CPU : ST-Ericsson U8500
Core ID : 4BA00477
Storage Device: ******* eMMC SEM08G
Device ID : 00450001
Block size : 512 bytes
Blocks : 15269888
Storage size : 7.3 Gb
Opening "C:\Program Files\GsmServer\Medusa\Firmware\SAMSUNG_GTI9070_Re pair.mf" file...
Writting BOOT section. Please wait...

Normandy

01-22-2013, 07:18	#1 (permalink)
roklat Freak Poster Join Date: Jan 2008 Location: freedoom ...algeria Posts: 484 Member: 686535 Status: Offline Sonork: 1592667 Thanks: 211 Thanked 106 Times in 68 Posts	i9070 and i9070p some ??? i need more info i9070p repaired by ort jtag done but the phone always dead Recommended Procedure : Connect JTAG Pinouts Connect USB Cable to phone Install USB Drivers "\drivers\STERICSSON_U8500" Click Repair Samsung GT-I9070 U8500 1.8V U8500 USB is ready! arm.tap,pos:0,IRLength:4,DeviceID:0x62286041 CPUID=0x62286041 U8500 IOLevel:1.8V FlashID:0x454D303845010053,SubFlashID:0x8F762F7647 9071AE BlockSize:512 PageSize:512 Actual Density:0x1D2000000 Writing Boot... 100% Boot restored. ..................................... U8500 USB is ready! Vref:1.834V TCK:05MHz Model:U8500_eMMC arm.tap,pos:0,IRLength:4,DeviceID:0x62286041. FlashID:0x454D303845010053,SubFlashID:0x8F762F7647 9071AE BlockSize:512 PageSize:512 Density:8192MB Actual Density:0x1D2000000 FlashName:SEM08G

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-27-2013, 17:21	#2 (permalink)
dimension_minaz Freak Poster Join Date: May 2010 Location: inside GSM Age: 26 Posts: 113 Member: 1297764 Status: Offline Thanks: 88 Thanked 4 Times in 4 Posts	U8500 USB is not ready. U8500 USB is not ready. U8500 USB is ready! Vref:1.834V TCK:05MHz Model:U8500_eMMC arm.tap,pos:0,IRLength:4,DeviceID:0x62286041. FlashID:0x454D303845010053,SubFlashID:0x3DAB9F5047 90B1C8 BlockSize:512 PageSize:512 Density:8192MB Actual Density:0x1D2000000 FlashName:SEM08G What is next step...?

01-29-2013, 17:37	#3 (permalink)
sp-lox Freak Poster Join Date: Oct 2001 Location: Moscow, Russia Age: 36 Posts: 270 Member: 6653 Status: Offline Sonork: 100.1597550 Thanks: 8 Thanked 25 Times in 8 Posts	What i not correctly do ??? Run ORT V1.89 select Samsung GT-I9070 click Scan log: U8500 USB is not ready. U8500 USB is not ready. U8500 USB is not ready. U8500 USB is not ready. U8500 USB is ready! Vref:1.834V TCK:05MHz Model:GT-I9070 arm.tap,pos:0,IRLength:4,DeviceID:0x62286041. FlashID:0x454D303845010053,SubFlashID:0x7284AFFC47 904055 BlockSize:512 PageSize:512 Density:8192MB Actual Density:0x1D2000000 FlashName:SEM08G Run EasyMode Select Samsung GT-I9070 log: Samsung GT-I9070 U8500 1.8V arm.tap,pos:0,IRLength:4,DeviceID:0x62286041 Scan CPU failed(-107)

01-30-2013, 16:46	#4 (permalink)
dimension_minaz Freak Poster Join Date: May 2010 Location: inside GSM Age: 26 Posts: 113 Member: 1297764 Status: Offline Thanks: 88 Thanked 4 Times in 4 Posts	ORT Team Plz guide us

01-30-2013, 17:35	#5 (permalink)
Tricom Freak Poster Join Date: May 2009 Posts: 309 Member: 1037562 Status: Offline Sonork: 100. Thanks: 268 Thanked 48 Times in 36 Posts	These 2 models are different even i9070 with different emmc size is dfferenr hardwares So "P" is not yet supported Best regards

03-15-2013, 21:17	#6 (permalink)
vistaunlock Freak Poster Join Date: Apr 2007 Location: the Land of the Cedars Posts: 321 Member: 497776 Status: Offline Thanks: 29 Thanked 36 Times in 24 Posts	PLZ help i update phone i9070p with HOME_I9070XXLQ4_I9070SERLQ4_660490_REV00_user_low_ ship.tar.md5 now phone is dead no boot even with JIC usb . trying JTAG and result : VREF = 0.0V is less than required level. Please check target device power supply. Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision B. ERROR[045]: Scan chain is too long or damaged. Scanned TAP ID's list: 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF MI: Medusa JTAG init failed. Normandy

03-15-2013, 21:26	#7 (permalink)
vistaunlock Freak Poster Join Date: Apr 2007 Location: the Land of the Cedars Posts: 321 Member: 497776 Status: Offline Thanks: 29 Thanked 36 Times in 24 Posts	Done , bad connection it was Connect successful. Disconnected Selected device model: Samsung GT-I9070 Connecting. Please wait... Resetting target. Please wait... Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision B. Detected TAP ID: 62286041, IR Length = 6. JTAG speed : 2400 KHz. VREF level : 1.77 V CPU : ST-Ericsson U8500 Core ID : 4BA00477 Storage Device: ******* eMMC SEM08G Device ID : 00450001 Block size : 512 bytes Blocks : 15269888 Storage size : 7.3 Gb Opening "C:\Program Files\GsmServer\Medusa\Firmware\SAMSUNG_GTI9070_Re pair.mf" file... Writting BOOT section. Please wait... Normandy