GSM-Forum - CPH1803 dead by other tool

GSM-Forum (https://forum.gsmhosting.com/vbb/)

- Easy-Jtag / Easy-Jtag Plus (https://forum.gsmhosting.com/vbb/f672/)

- - CPH1803 dead by other tool (https://forum.gsmhosting.com/vbb/f672/cph1803-dead-other-tool-2732667/)

CPH1803 dead by other tool

this device has been killed by other tool .
I d like fix by easy ; is the log below is correct ?
I get error when I try to write Boot1/2/3

Quote:

---------- eMMC Device Information ----------

eMMC CID : 150100514536334D42035050063755B2
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2018 Rev.0x3
eMMC NAME: QE63MB , S/N: 1347421751
eMMC NAME (HEX): 514536334D42
IC Name: Samsung , KMQE60013M-B318/16GB @BGA221
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 22908 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: QE63MB_1347421751_20191124_0705.extcsd
Caution: invalid main GPT header, but valid a backup header!
Warning: Invalid CRC on main header data; loaded backup partition table.
EFI Table CRC Check FAIL.
Warning! Main partition table CRC mismatch! Loaded backup
Warning! One or more CRCs don't match. You should repair the disk!
Real (Hardware) Disk/Image size: 1D1F000 sectors 14.6 GiB
Soft (Partitioned) Disk/Image size: 1D1EFDA sectors 14.6 GiB
Disk identifier (GUID): 9243B553-F89A-CA74-5258-899B6739094A
Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30535661
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Build ID: OPM1.171019.026
Release Base ID: 8.1.0
Architecture ABI: arm64-v8a
Device manufacturer: OPPO
Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190529.191350 release-keys
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (9.184GB)
Unable to mount USERDATA , code : 95
Done.

try to reduce the frequency of low frequence to see if the error still occurs
from 4-12 mhz
https://www.youtube.com/watch?v=KQTSoyZ1xLw&t=603s

I let you know once I try .

till getting error ,

Quote:

Setting frequence to 14 MHz
CMD Pullup Level: 247 mV
CMD Active Level: 2547 mV
EMMC Device Information :
EMMC CID: 150100514536334D42035050063755B2
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 50500637 , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2018
EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 22908 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_50500637_20191124_223519.extcsd
EMMC Init completed.

Scanning soft partitions
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #4
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #5
Too many errors. Reading has been stopped

can't use universal format

Quote:

Setting frequence to 14 MHz
CMD Pullup Level: 2010 mV
CMD Active Level: 2536 mV
EMMC Device Information :
EMMC CID: 150100514536334D42035050063755B2
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 50500637 , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2018
EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 22908 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_50500637_20191124_223736.extcsd
EMMC Init completed.

Operation: Universal Factory Format
Please, wait ...
Error: 21 Verification error

cn't read too

Operation: Reading from eMMC...

Quote:

Reading from: ROM2 , start: 0x000000000000 , size: 0x000000400000
Output file: C:\Users\Amin\Desktop\OPPO MODEM\read\EMMC_QE63MB_ROM2_000000000000_000000400 000.bin
eMMC switching to ROM2
Reading partition...
Error reading at address: 000000018000 , error: -4, DATA RCV CRC Error ... Retry #1
Error reading at address: 000000018000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000020000 , error: -206, PORT Read Error ... Retry #1
Error reading at address: 000000020000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000020000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Reading has been stopped
Try the "Skip unreadable blocks" option

Quote:

Originally Posted by psytr0nic (Post 13908269)

till getting error ,

can't use universal format

What box (1st, 2nd?)
try to use Hi Power ISP mode

Hi Power mode:

1) for OLD Box (COLOR box) with 1.xx box firmware

Short 4 CLK wires together
Set Clk rate 21/14MHz
Set IO level 2,8/1.8V
Set "HiPower CLK mode"
Connect to board only GND, CMD/CLK/Dat_0
Connect USB power to board

2) for NEW Box (Black-White box) with 2.xx box firmware

Use complect ISP adapter (use 1 line CLK)
Set Clk rate 18/24MHz
Set IO level 1.8V
Set "HiPower CLK mode"
Connect to board only GND, CMD/CLK/Dat_0
Connect USB power to board

Quote:

Originally Posted by layder (Post 13909542)

Hi Power mode:

1) for OLD Box (COLOR box) with 1.xx box firmware

Short 4 CLK wires together
Set Clk rate 21/14MHz
Set IO level 2,8/1.8V
Set "HiPower CLK mode"
Connect to board only GND, CMD/CLK/Dat_0
Connect USB power to board

2) for NEW Box (Black-White box) with 2.xx box firmware

Use complect ISP adapter (use 1 line CLK)
Set Clk rate 21MHz
Set IO level 1.8V
Set "HiPower CLK mode"
Connect to board only GND, CMD/CLK/Dat_0
Connect USB power to board

OK I try and let you know thank

is my info is correct ? I have GPT issu how can I fix it ?
none write operation is accepted , with all giving setting

Quote:

HiPower mode is ON
Setting frequence to 14 MHz
CMD Pullup Level: 2000 mV
CMD Active Level: 2598 mV
EMMC Device Information :
EMMC CID: 150100514536334D42035050063755B2
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 50500637 , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2018
EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 22908 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_50500637_20191128_000554.extcsd
EMMC Init completed.

can someone share with me CPH1803 QE63MB.extcsd backup ? maybe it could save

how to fix that ?

Quote:

Caution: invalid main GPT header, but valid a backup header!
Warning: Invalid CRC on main header data; loaded backup partition table.
Warning! Main and backup partition tables differ!
Warning! Main partition table CRC mismatch! Loaded backup
Warning! One or more CRCs don't match. You should repair the disk!
Real (Hardware) Disk/Image size: 1D1F000 sectors 14.6 GiB
Soft (Partitioned) Disk/Image size: 1D1EFDA sectors 14.6 GiB
Disk identifier (GUID): 00000000-0000-0000-0000-000000000000
Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30535661
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Unable to mount SYSTEM , code : 95
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (9.184GB)
Unable to mount USERDATA , code : 95