Easy-JTAG 1.1.x.x - HIGH speed EMMC Direct core 2.0 Beta testing before release. - Page 4 - GSM-Forum

AhsanNawaz · 05-15-2014, 12:02

Quote:

Originally Posted by titanic

Z3X EasyJtag Software ver. 1.3.3.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 0606F80FA22B6D2F, ,FW Ver.: 01.50
Warning: CMD Pullup Level (1144 mV) too low , check cables etc.!!!
CMD Active Level:1536 mV
eMMC Device Information
EMMC CID : 15010056545530304DF1844034AA9F5A
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 09/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 2218800298
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2218800298_20140402_1215.extcsd
Done.
Running:SAMSUNG: Smart Factory Reset + Format...
Z3X EasyJtag Software ver. 1.3.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:1536 mV
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_2218800298_20140 402_1215.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 1.3.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:1536 mV
Writing...
Done!
Done.
Please don't forget to repair extCSD from backup!!!
Z3X EasyJtag Software ver. 1.3.3.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 0606F80FA22B6D2F, ,FW Ver.: 01.50
Warning: CMD Pullup Level (1134 mV) too low , check cables etc.!!!
CMD Active Level:1536 mV
eMMC Device Information
EMMC CID : 15010056545530304DF1844034AA9F5A
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 09/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 2218800298
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2218800298_20140402_1217.extcsd
Done.
Writing file...D:\Phones\Easy Jtag\N7100\ROM2_GT-N7100_v2\EMMC_00000000_00200000.bin
Z3X EasyJtag Software ver. 1.3.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1134 mV
CMD Active Level:1536 mV
Writing 000000200000 bytes to 00000000 ...ROM2
Write Speed: 1723 kB/s
Done !!!

BR,

hello i have same problem....can u help me.

Z3X EasyJtag Software ver. 1.3.4.3
Loading eMMC Addon Firmware... IO: 2450 mV
Box S/N: 1616070D14A51DC6, ,FW Ver.: 01.50
CMD Pullup Level:1485 mV
CMD Active Level:1784 mV
eMMC Device Information
EMMC CID : 15010056545530304DF18F1145649FBA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0000 , OEM ID: 0000
EMMC Date: 00/0000 Rev.0x0
EMMC NAME: , S/N: 0
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line !!!

umerfarooq · 05-15-2014, 12:58

EasyJtag Suite ver.: 1.3.4.3 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
Successefuly connected to box on COM7Box S/N: 18FF900BE3CD5E21, ,FW Ver.: 01.50Box Working Mode: JTAG Box.Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AAFA-E5F5 , ver: 22
Z3X EasyJtag Software ver. 1.3.4.3
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 18FF900BE3CD5E21, ,FW Ver.: 01.50
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
eMMC Device Information
EMMC CID : 15010056545530304DF156273F257FAC
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 1445412645
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_1445412645_20140404_1336.extcsd
Done.
Running:SAMSUNG: Smart Factory Reset + Format...
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
Running:SAMSUNG: MoviNAND Format...
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!!!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_1445412645_20140 404_1336.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Writing...
Done!
Done.
Please don't forget to repair extCSD from backup!!!
Writing file...D:\BOX-SETUP\J-TAG\EASY-JTAG\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM2_00000000_00200000.bin
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail !!!
Write Block Failed, Reason: DATA SND CRC Error
Writing file...D:\BOX-SETUP\J-TAG\EASY-JTAG\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Writing 000020000000 bytes to 00000000 ...ROM1
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail !!!
Write Block Failed, Reason: DATA SND CRC Error

umerfarooq · 05-15-2014, 13:19

i notice that only s3 no:216 on EMMc and note2 no:219 and some time no:234 are working perfect for repairing dead boot and specially for product code at this moment i have no logs available but as soon available i post here. i almost done 30 mobiles S3 and 10 note2 mention above no on emmc.others not detected. i think this information help EASY JTAG team for improvement their software in next updates

dj.orion · 05-16-2014, 18:00

Quote:

Originally Posted by umerfarooq

i notice that only s3 no:216 on EMMc and note2 no:219 and some time no:234 are working perfect for repairing dead boot and specially for product code at this moment i have no logs available but as soon available i post here. i almost done 30 mobiles S3 and 10 note2 mention above no on emmc.others not detected. i think this information help EASY JTAG team for improvement their software in next updates

Can U explain more..
What meaning n where is no:216, 219 n 234, phisically seen or via log.?

I get N7100 dead for several times n facing can't do write to eMMC
But can do read n formating
eMMC became read only memory

...
Look at Ur log n mine, had same error in writing process

Is this positive eMMC totaly can't repaired.?

Code:

Successfully connected to box on COM69
Box S/N: XXXXXX, ,FW Ver.: 01.48
Z3X EasyJtag Software ver. 1.0.109.0
Loading eMMC Addon Firmware...
CMD Pullup Level:1639 mV
CMD Active Level:2310 mV
EMMC CID 15010056545530304DF104260B109F0B
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 09/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 69602064
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Writing 000000200000 bytes to 00000000 ...ROM3
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Writing eMMC flash page stopped by user request

umerfarooq · 05-16-2014, 19:40

not in logs check at the top of right side on EMMc CHIP

tavo_unlock · 05-16-2014, 21:36

blang new version present fail in conecction tested in i9300 ?

umerfarooq · 05-17-2014, 13:00

cchajmu · 05-04-2015, 15:57

any body fcae this problem

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 04040217523E5ACE, ,FW Ver.: 01.52
CMD Pullup Level:1412 mV
CMD Active Level:2062 mV
eMMC Device Information
EMMC CID : 1501004D4147344642F71C3E2EF8CFC2
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 12/2012 Rev.0xF7
EMMC NAME: MAG4FB , S/N: 473837304
EMMC NAME (HEX): 4D414734464200
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.

oktay50000 · 05-04-2015, 17:31

Yes im facing it too after update to ver 2 other emmc box connect ok

dimas_lumazank · 05-05-2015, 23:46

Quote:

Originally Posted by BABAK NURI

Hi
Speed is like Jet....It's Great

hei... riff user need you, but you stand here. are you product suporter or just user???

momin.m2 · 12-27-2015, 10:56

Z3X EasyJtag Software ver. 2.0.5.1
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 14007016C09E928B, ,FW Ver.: 01.52
CMD Pullup Level:2196 mV
CMD Active Level:2897 mV
eMMC Device Information
EMMC CID : 1501004C3758484D4203A7BBBCACC09C
EMMC CSD : D02701320F5903FFF6DBFFEF8E406068
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 12/2013 Rev.0x3
EMMC NAME: L7XHMB , S/N: 2814098604
EMMC NAME (HEX): 4C3758484D4200
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!

DataMunched · 04-21-2016, 07:48

Thank you
I found this post very helfull

alex_030385 · 06-25-2016, 12:03

Z3X EasyJtag Software ver. 2.1.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0701001D36DA3BF9, ,FW Ver.: 01.55
CMD Pullup Level:1763 mV
CMD Active Level:2320 mV
Box IO Level:2800 mV
CLK Rate:1000 khz
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 90014A4838473264040300A529EB11A2
EMMC CSD : D02701320F5903FFFFFFFFEF8A4040D2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 01/2014 Rev.0x3
EMMC NAME: H8G2d , S/N: 10824171
EMMC NAME (HEX): 48384732642000
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.

ihave also same problem fifo???

Niaz Hussain · 10-10-2016, 14:52

Z3X EasyJtag Software ver. 2.3.0.1
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N:------------, ,FW Ver.: 01.55CMD Pullup Level:1619 mV
CMD Active Level:2310 mV
Box IO Level:1800 mV
CLK Rate:7000 khz
HiPower mode is off!
---------- eMMC Device Information ----------EMMC CID : 90014A483447326211012D26118F82BC
EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 08/2015 Rev.0x1
EMMC NAME: H4G2b , S/N: 757469583
EMMC NAME (HEX): 48344732622000
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.

harold6x · 10-10-2016, 16:29

Error (404)
We can't find the page you're looking for

05-04-2015, 17:31	#54 (permalink)
oktay50000 No Life Poster Join Date: Jan 2008 Location: Under the Sky Posts: 749 Member: 678886 Status: Offline Sonork: 100.1661586 Thanks Meter: 171	Yes im facing it too after update to ver 2 other emmc box connect ok Last edited by oktay50000; 05-04-2015 at 17:38.

12-27-2015, 10:56	#56 (permalink)
momin.m2 Junior Member Join Date: Jun 2009 Location: Osmanabad.Mharastra.india Posts: 11 Member: 1051866 Status: Offline Sonork: 100.1669165 Thanks Meter: 3	any on halp me Z3X EasyJtag Software ver. 2.0.5.1 Loading eMMC Addon Firmware... IO: 3300 mV Box S/N: 14007016C09E928B, ,FW Ver.: 01.52 CMD Pullup Level:2196 mV CMD Active Level:2897 mV eMMC Device Information EMMC CID : 1501004C3758484D4203A7BBBCACC09C EMMC CSD : D02701320F5903FFF6DBFFEF8E406068 EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 12/2013 Rev.0x3 EMMC NAME: L7XHMB , S/N: 2814098604 EMMC NAME (HEX): 4C3758484D4200 Can't init EMMC, Reason: CARD Data FIFO Timeout Error Check Data Line!

10-10-2016, 14:52	#59 (permalink)
Niaz Hussain Freak Poster Join Date: Feb 2005 Location: Pakistan Hyderabad Age: 40 Posts: 258 Member: 117640 Status: Offline Sonork: 100.1580505 Thanks Meter: 62	J110H/DS dead boot Z3X EasyJtag Software ver. 2.3.0.1 Loading eMMC Addon Firmware... IO: 1800 mV Box S/N:------------, ,FW Ver.: 01.55CMD Pullup Level:1619 mV CMD Active Level:2310 mV Box IO Level:1800 mV CLK Rate:7000 khz HiPower mode is off! ---------- eMMC Device Information ----------EMMC CID : 90014A483447326211012D26118F82BC EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacturer ID: 0090 , OEM ID: 014A EMMC Date: 08/2015 Rev.0x1 EMMC NAME: H4G2b , S/N: 757469583 EMMC NAME (HEX): 48344732622000 Can't init EMMC, Reason: CARD Data FIFO Timeout Error Check Data Line! Done.

05-15-2014, 12:58	#47 (permalink)
umerfarooq Freak Poster Join Date: Jul 2007 Posts: 183 Member: 540932 Status: Offline Thanks Meter: 36	EasyJtag Suite ver.: 1.3.4.3 / wxWidgets 3.1.0-W-U started. Operating system ver.: Windows 7 (build 7601, Service Pack 1). Successefuly connected to box on COM7Box S/N: 18FF900BE3CD5E21, ,FW Ver.: 01.50Box Working Mode: JTAG Box.Box Drivers version: 3.0.0.0, are OK Z3X Card Serial : AAFA-E5F5 , ver: 22 Z3X EasyJtag Software ver. 1.3.4.3 Loading eMMC Addon Firmware... IO: 1850 mV Box S/N: 18FF900BE3CD5E21, ,FW Ver.: 01.50 CMD Pullup Level:1103 mV CMD Active Level:1433 mV eMMC Device Information EMMC CID : 15010056545530304DF156273F257FAC EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 Rev.0xf1 EMMC NAME: VTU00M , S/N: 1445412645 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_1445412645_20140404_1336.extcsd Done. Running:SAMSUNG: Smart Factory Reset + Format... Z3X EasyJtag Software ver. 1.3.4.3 Skip loading eMMC Addon Firmware CMD Pullup Level:1103 mV CMD Active Level:1433 mV Sending Smart Wipe Request... Wiping Card... Please do not touch it!!! Done. Please don't forget to repair extCSD from backup!!! Running:SAMSUNG: MoviNAND Format... Z3X EasyJtag Software ver. 1.3.4.3 Skip loading eMMC Addon Firmware CMD Pullup Level:1103 mV CMD Active Level:1433 mV EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Sending Internal Reconfiguration Request... Waiting configuration Apply!!! Restoring configuration... EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Wiping Card... Please do not touch it!!! Done. Please don't forget to repair extCSD from backup!!! extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_1445412645_20140 404_1336.extcsd Running:Repair extCSD... Z3X EasyJtag Software ver. 1.3.4.3 Skip loading eMMC Addon Firmware CMD Pullup Level:1103 mV CMD Active Level:1433 mV Writing... Done! Done. Please don't forget to repair extCSD from backup!!! Writing file...D:\BOX-SETUP\J-TAG\EASY-JTAG\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM2_00000000_00200000.bin Z3X EasyJtag Software ver. 1.3.4.3 Skip loading eMMC Addon Firmware CMD Pullup Level:1103 mV CMD Active Level:1433 mV Writing 000000200000 bytes to 00000000 ...ROM2 Retry writing adress 0x00000000 (Attempt #1)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #2)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #3)... Retry Fail !!! Write Block Failed, Reason: DATA SND CRC Error Writing file...D:\BOX-SETUP\J-TAG\EASY-JTAG\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin Z3X EasyJtag Software ver. 1.3.4.3 Skip loading eMMC Addon Firmware CMD Pullup Level:1103 mV CMD Active Level:1433 mV Writing 000020000000 bytes to 00000000 ...ROM1 Retry writing adress 0x00000000 (Attempt #1)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #2)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #3)... Retry Fail !!! Write Block Failed, Reason: DATA SND CRC Error

05-15-2014, 13:19	#48 (permalink)
umerfarooq Freak Poster Join Date: Jul 2007 Posts: 183 Member: 540932 Status: Offline Thanks Meter: 36	i notice that only s3 no:216 on EMMc and note2 no:219 and some time no:234 are working perfect for repairing dead boot and specially for product code at this moment i have no logs available but as soon available i post here. i almost done 30 mobiles S3 and 10 note2 mention above no on emmc.others not detected. i think this information help EASY JTAG team for improvement their software in next updates

05-16-2014, 19:40	#50 (permalink)
umerfarooq Freak Poster Join Date: Jul 2007 Posts: 183 Member: 540932 Status: Offline Thanks Meter: 36	not in logs check at the top of right side on EMMc CHIP

05-16-2014, 21:36	#51 (permalink)
tavo_unlock No Life Poster Join Date: Jul 2008 Location: infinity Posts: 771 Member: 817412 Status: Offline Sonork: 1618066 Thanks Meter: 69	blang new version present fail in conecction tested in i9300 ?

05-17-2014, 13:00	#52 (permalink)
umerfarooq Freak Poster Join Date: Jul 2007 Posts: 183 Member: 540932 Status: Offline Thanks Meter: 36

05-04-2015, 15:57	#53 (permalink)
cchajmu Freak Poster Join Date: Jul 2009 Posts: 174 Member: 1073769 Status: Offline Thanks Meter: 34	any body fcae this problem Z3X EasyJtag Software ver. 1.9.0.5 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 04040217523E5ACE, ,FW Ver.: 01.52 CMD Pullup Level:1412 mV CMD Active Level:2062 mV eMMC Device Information EMMC CID : 1501004D4147344642F71C3E2EF8CFC2 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 12/2012 Rev.0xF7 EMMC NAME: MAG4FB , S/N: 473837304 EMMC NAME (HEX): 4D414734464200 Can't init EMMC, Reason: CARD Data FIFO Timeout Error Check Data Line! Done.

04-21-2016, 07:48	#57 (permalink)
DataMunched Junior Member Join Date: Nov 2015 Posts: 16 Member: 2491556 Status: Offline Thanks Meter: 2	Thank you I found this post very helfull

06-25-2016, 12:03	#58 (permalink)
alex_030385 No Life Poster Join Date: Oct 2008 Age: 39 Posts: 1,478 Member: 875541 Status: Offline Sonork: 100.1604468 Thanks Meter: 327	Z3X EasyJtag Software ver. 2.1.1.1 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 0701001D36DA3BF9, ,FW Ver.: 01.55 CMD Pullup Level:1763 mV CMD Active Level:2320 mV Box IO Level:2800 mV CLK Rate:1000 khz HiPower™ mode is ON! eMMC Device Information EMMC CID : 90014A4838473264040300A529EB11A2 EMMC CSD : D02701320F5903FFFFFFFFEF8A4040D2 EMMC Manufacturer ID: 0090 , OEM ID: 014A EMMC Date: 01/2014 Rev.0x3 EMMC NAME: H8G2d , S/N: 10824171 EMMC NAME (HEX): 48384732642000 Can't init EMMC, Reason: CARD Data FIFO Timeout Error Check Data Line! Done. ihave also same problem fifo???

10-10-2016, 16:29	#60 (permalink)
harold6x No Life Poster Join Date: Apr 2006 Location: syria Age: 46 Posts: 909 Member: 257716 Status: Offline Sonork: 1650684 Thanks Meter: 57	Error (404) We can't find the page you're looking for