Easy-JTAG HOT Update. v1.9.1.0. Repair dead EMMC KMVYL000LM-B503!! First in World

[NoName®]

Easy-JTAG Very HOT Update. v1.9.1.0 Lot of changes:

Improved Samsung eMMC firmware update protocol
Added Samsung eMMC firmwares for new eMMCs:

• Samsung KMVYL000LM-B503 [VYL00M] Fix NAME 000000
• Samsung KMVYL000LM-B503 [VYL00M] Fix OCR READY TIMEOUT ERROR [EMMC DEAD])
• eMMC Repair FIRMWARE Samsung KMSJS000KA-B308 [SJS00A]
• eMMC Repair FIRMWARE Samsung KMV3U000LM-B304 [V3U00M]
• eMMC Repair FIRMWARE Samsung KLM8G2FB3B-D001 [M8G2FB]

STEP BY STEP MANUAL HERE

Added NEW eMMC TP pinouts (Look inside sw folder: /EMMC TP PINOUTS)

Added via JTAG:

• GSMART G1362 (Read/Write/Pinouts/Dump/RCP) FIRST IN THE WORLD!

Added via eMMC DIRECT(ISP)

• Samsung GT-I9060(Read/Write/Pinout/Dump)
• LG P715(Read/Write/Pinout/Dump)

P.S. KMVYL000LM Repair solution are waiting for Advanced Copy'n'Pasters.
P.P.S This solution are made in one day and free as every Z3X Update last 10 years.

[omshan]

nice update sir. im using z3x box very use full this box.
please update sandisk eMMC firmware update too

[rasheedc007]

with out remoove emmc ic solution need. its hard .no more doing people..and emmc socket no have...when remoove eemc damege coming more.....

[blang]

Originally Posted by rasheedc007

with out remoove emmc ic solution need. its hard .no more doing people..and emmc socket no have...when remoove eemc damege coming more.....

Solution without TP will not exist never!!!

if this hard for you, then buy new emmc and solder inside(this is very easy).


no more words.!!!

[alanic]

Help team..

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVYL000LM-B503
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2134 mV
CMD Active Level:2609 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

[blang]

Originally Posted by alanic

Help team..

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVYL000LM-B503
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2134 mV
CMD Active Level:2609 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

did you Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] when sw say to do? there are 20second you have to do that?

[alanic]

whether that is in the intention when the program says , then I disconnect the power EMMC CMD CLK D0 (in socket) , then after 20 seconds reconnect ?

[oktay50000]

mr blang tnx for good update but:
1-please change device selection drop box font to smaller size i cant see complete htc modes
2-and please make application save phone model on exit

everytime when exiting application forgets last phone model

[NoName®]

Originally Posted by alanic

whether that is in the intention when the program says , then I disconnect the power EMMC CMD CLK D0 (in socket) , then after 20 seconds reconnect ?

Hi

Reconnect not after 20 sec !!! Reconnect during progress bar is moving, then wait fw update complete success. When don't reconnect before progress bar complete 20 sec timeout, CID write fail and eMMC name 000000, but operable.

"Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!"

Best Regards

[waqas317]

U can add samsung i9515 model

[BABAK NURI]

Hi
KMVYL000LM-B503 Work Perfectly :

Running:SAMSUNG: eMMC firmware update...
EMMC NAME: VYL00M
Z3X EasyJtag Software ver. 1.9.0.6
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0707080F587D5F84, ,FW Ver.: 01.52
CMD Pullup Level:2124 mV
CMD Active Level:2691 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

[alanic]

Originally Posted by NoName®

Hi

Reconnect not after 20 sec !!! Reconnect during progress bar is moving, then wait fw update complete success. When don't reconnect before progress bar complete 20 sec timeout, CID write fail and eMMC name 000000, but operable.

"Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!"

Best Regards

I have do during the process of moving the bar before time runs 20 seconds.
but still the same, I wait after that,
until the progress bar move is completed (20 seconds)
Unable to init the device, Reason: OCR errors Ready Timeout [Check VCC or eMMC OFF]
Done.

whether the chip may have been damaged in total?

[NoName®]

Originally Posted by alanic

I have do during the process of moving the bar before time runs 20 seconds.
but still the same, I wait after that,
until the progress bar move is completed (20 seconds)
Unable to init the device, Reason: OCR errors Ready Timeout [Check VCC or eMMC OFF]
Done.

whether the chip may have been damaged in total?

Could you reconnect eMMC after that and start Smart Report ?
If can't read Smart Report this eMMC can not be recovered.
Typically 95% damaged chips can be recovered.

Thanks

[alanic]

Originally Posted by NoName®

Could you reconnect eMMC after that and start Smart Report ?

Thanks

after failed then not connected anymore :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2114 mV
CMD Active Level:2516 mV
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

then I did connect a test point again, detected 0000 :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2124 mV
CMD Active Level:2619 mV
eMMC Device Information
EMMC CID : 150100303030303030002010021200E6
EMMC CSD : D02701320F5903FFF6DBFFE796404052
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 00/2013 Rev.0x0
EMMC NAME: 000000 , S/N: 537920018
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 8192 MB
EMMC ROM2 (Boot Partition 1) Capacity: 1024 kB
EMMC ROM3 (Boot Partition 2) Capacity: 1024 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 1024 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537920018_20150306_0234.extcsd
Done.


smart report the results of the current condition of 0000 :
Running:SAMSUNG: Read S.M.A.R.T Report...
Z3X EasyJtag Software ver. 1.9.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1155 mV
CMD Active Level:1650 mV
Reading S.M.A.R.T
Can't init device, Reason: CARD Ready Timeout Error
Done.


log before updating the firmware :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2124 mV
CMD Active Level:2588 mV
eMMC Device Information
EMMC CID : 15010056594C30304D198ED776117E30
EMMC CSD : D02701320F5903FFF6DBFFEF8A404066
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2011 Rev.0x19
EMMC NAME: VYL00M , S/N: 2396485137
EMMC NAME (HEX): 56594C30304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VYL00M_2396485137_20150306_0240.extcsd
Done.

Running:SAMSUNG: Read S.M.A.R.T Report...
Z3X EasyJtag Software ver. 1.9.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2124 mV
CMD Active Level:2588 mV
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode : Normal
Super Block size : 0x00400000 (4194304 bytes)
Super Page size : 0x00008000 (32768 bytes)
Optimal Write size : 0x00008000 (32768 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00040000 (262144 bytes)
Total Number of banks : 2
Initial bad blocks per bank : 6,7,0,0
Runtime bad blocks per bank : 1,1,0,0
Reserved blocks left per bank : 134,133,0,0
All Erase counts (min,avg,max): 0,3167,65535
SLC Erase counts (min,avg,max): 0,24099,65535
MLC Erase counts (min,avg,max): 803,950,6402
S.M.A.R.T Report Done.

after the last failed firmware update like this :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0800B006F662B313, ,FW Ver.: 01.52
CMD Pullup Level:2114 mV
CMD Active Level:2516 mV
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

[NoName®]

Originally Posted by alanic

after failed then not connected anymore :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2114 mV
CMD Active Level:2516 mV
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

then I did connect a test point again, detected 0000 :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2124 mV
CMD Active Level:2619 mV
eMMC Device Information
EMMC CID : 150100303030303030002010021200E6
EMMC CSD : D02701320F5903FFF6DBFFE796404052
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 00/2013 Rev.0x0
EMMC NAME: 000000 , S/N: 537920018
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 8192 MB
EMMC ROM2 (Boot Partition 1) Capacity: 1024 kB
EMMC ROM3 (Boot Partition 2) Capacity: 1024 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 1024 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537920018_20150306_0234.extcsd
Done.


smart report the results of the current condition of 0000 :
Running:SAMSUNG: Read S.M.A.R.T Report...
Z3X EasyJtag Software ver. 1.9.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1155 mV
CMD Active Level:1650 mV
Reading S.M.A.R.T
Can't init device, Reason: CARD Ready Timeout Error
Done.


log before updating the firmware :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxx, ,FW Ver.: 01.52
CMD Pullup Level:2124 mV
CMD Active Level:2588 mV
eMMC Device Information
EMMC CID : 15010056594C30304D198ED776117E30
EMMC CSD : D02701320F5903FFF6DBFFEF8A404066
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2011 Rev.0x19
EMMC NAME: VYL00M , S/N: 2396485137
EMMC NAME (HEX): 56594C30304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VYL00M_2396485137_20150306_0240.extcsd
Done.

Running:SAMSUNG: Read S.M.A.R.T Report...
Z3X EasyJtag Software ver. 1.9.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2124 mV
CMD Active Level:2588 mV
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode : Normal
Super Block size : 0x00400000 (4194304 bytes)
Super Page size : 0x00008000 (32768 bytes)
Optimal Write size : 0x00008000 (32768 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00040000 (262144 bytes)
Total Number of banks : 2
Initial bad blocks per bank : 6,7,0,0
Runtime bad blocks per bank : 1,1,0,0
Reserved blocks left per bank : 134,133,0,0
All Erase counts (min,avg,max): 0,3167,65535
SLC Erase counts (min,avg,max): 0,24099,65535
MLC Erase counts (min,avg,max): 803,950,6402
S.M.A.R.T Report Done.

after the last failed firmware update like this :
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0800B006F662B313, ,FW Ver.: 01.52
CMD Pullup Level:2114 mV
CMD Active Level:2516 mV
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

Hi,
Your eMMC was working before firmware update ?
Did you disconnect TP after 000000 detection,
before start firmware update?
Thanks